Fisher-Price R4743 User manual

R4743
Newborn
0-3 months
and up to 4,5kg (10 lbs)
Infant
3-6 months
and up to 9kg (20 lbs)
Toddler
6 months+
and up to 11kg (25 lbs)
www.fisher-price.co.uk
IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE.
WARNING

2
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken. Contact
Fisher-Price®for replacement parts and instructions if needed.
Never substitute parts.
• Please read these instructions before use of this product.
• Adult assembly is required. Tool needed for assembly:
Phillips screwdriver (not included).
• Water toys sometimes get messy. Protect play surfaces
before use.
• Overfilling the bathtub may cause it to leak.
• After each use, drain and rinse all items.
• The sling is machine washable. Machine wash, cold on the
gentle cycle. Do not use bleach. Tumble dry on low.
• Product features and decoration may vary from the photographs.
2 Toys Infant Insert 2 Bases
This product contains small parts in its
unassembled state. Adult assembly is required.
Parts
Bathtub
DROWNING HAZARD
• Babies have DROWNED in infant bath tubs.
• Babies can drown in as little as 2,5 cm
(1inch) of water.
• ALWAYS bathe your baby in as little
water as possible.
• ALWAYS keep baby within adult’s reach.
•NEVER allow other children to substitute
for adult supervision.
• NEVER lift this product with baby in it.
• NEVER place this product in water in an
adult bathtub or sink. ALWAYS keep the
drain open in the adult bath tub or sink.
• ALWAYS test this product for secure fit
in domestic sink or bath. For domestic
use only.
• ALWAYS test water temperature for
comfort on wrist before placing baby
in this product.
Consumer Information
WARNING CAUTION
#8 x 1,9 cm (3/4")Screw – 2
Fastener Shown Actual Size
Sling

3
Temperature Guide
Typical water temperature should be between 32°C and 38°C.
This product has a temperature guide located on the bathtub floor
to help gauge the right water temperature for baby. Use of this
temperature guide should not replace testing the water temperature
with your hand or elbow before placing baby in this product.
Note: If water temperature is too cold (below 28°C) or too hot
(58°C). no image will appear on the temperature guide.
Water temperature is too cold for baby.
Add warm water.
Water temperature is just right for baby.
Water temperature is too hot for baby.
Add cold water.
One - Time Assembly
• Match the number on each base to the number near each
socket on the bathtub. Fit the bases to the bathtub.
• Insert a screw into each base and tighten with a Phillips
screwdriver. Do not over-tighten.
Bathtub
Bases

4
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.
©2009 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN MEXICO R4743a-0726
Great Britain: Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500303. www.service.mattel.com/uk.
Asia: Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China.
Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd. (993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana
Golf Country Resort, 47410 PJ. Tel: [phone].
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.

5
Infant
Fit the bathtub to the sink, or place on a flat surface.•
Fit the plug into the hole in the bottom of the bathtub. Fill•
the bathtub with as little water as possible to bathe baby.
ALWAYS test water temperature in the product with your
hand or elbow before placing baby in this product.
Note: This product includes a temperature guide to help gauge
the water temperature (see Temperature Guide section).
Carefully place baby in the bathtub.•
Infant Insert
Fit the infant insert in the bathtub.•
Newborn
• Fit the clips near the rounded end of the sling to the notch
on each side of the bathtub opposite the plug. Fit the clips
on the other end of the sling to the remaining notches on the
other end of the bathtub.
ClipsClips
• Fit the bathtub to the sink, or place on a flat surface.
• Fit the plug into the hole in the bottom of the bathtub. Fill
the bathtub with as little water as possible to bathe baby.
ALWAYS test water temperature in the product with your
hand or elbow before placing baby in this product.
Note: This product includes a temperature guide to help gauge
the water temperature (see Temperature Guide section).
• Carefully place baby on the sling.

6
Toddler
• Place the bathtub in a larger bathtub, or place on a flat surface.
• Fit the plug into the hole in the bottom of the bathtub. Fill
the bathtub with as little water as possible to bathe baby.
ALWAYS test water temperature in the product with your
hand or elbow before placing baby in this product.
Note: This product includes a temperature guide to help gauge
the water temperature (see Temperature Guide section).
• Carefully place baby in the bathtub.
Pull apart the sides of the bathtub and remove the infant insert.•
Infant Insert
Storage
Bottom View
Before storing, drain, clean, rinse and dry all items.•
Turn the hook on the bathtub to hang it up for storage.•