Nugens NW-200TR User manual

1
Quick Installation Guide
NW-200TR
Wireless HDMI Transmitter and Receiver

2
1. Introduction
Package Contents
1. HDMI Transmitter TX x 1
2. HDMI Receiver RX x 1
3. External Antenna x 4
4. Power Transformers x 2
5. Infrared Booster Transmitter x 1
6. Infrared Booster Receiver x 1
7. Quick Installation Guide x 1
Overview
① HDMI In ② HDMI Out ③ Infrared Out
④ Status Light ⑤ Power Indicator Light ⑥ Power In DC12V

3
*Back
⑦ HDMI Out ⑧ Infrared In ⑨ Status Light
⑩ Power Indicator Light ⑪ Power In DC12V ⑫ Antenna Connector
⑬ Antenna Connector ⑭ Reset Button
Product Specification
Video
HDMI/HDCP
HDMI V1.4 / HDCP V1.2
Compression format
H.264
Maximum pixel clock
165MHz
Maximum data rate
6.75Gbps
Resolution
1920X1080
@60Hz (Max.) FULL HD
Connector
HDMI Type-A
Impedance
100Ω
Recommended HDMI maximum
input/output range
When 1920 x 1080 @ 60Hz,
<3m
Infrared
Interface
3.5mm IR port
Signal direction
Unidirectional
Signal type
Digital
Signal frequency
20-60kHz
Wi-Fi
Wireless transmission max.
power
13dbm
Wireless transmission standard
802.11ac
Signal direction
Unidirectional
Wireless transmission
frequency band
5GHz
Transmission distance
200m
Antenna type
Omnidirectional antenna

4
2. Instructions
Thank you for purchasing the Nugens NW-200TR Wireless HDMI Transmitter
and Receiver
- This product can connect up to 4 receivers with 1 transmitter, and a total can
be displayed up to 4 displays.
- The transmitter and receiver are paired right out of the factory; a set of plug-
and-play devices.
- Connect more than 2 receivers need to be paired manually, please refer to
the pairing instructions.
Note: You can identify the "Transmitter" and "Receiver" from the product.
Port
Transmitter
HDMI In x 1
HDMI Out x 1
IR Out x 1
Power In DC 12V x 1
Receiver
HDMI Out x 1
IR In x 1
Power in DC 12V x 1
LED
Indicator
Light
Transmitter
Sta Status LED x 1
Pow Power LED x 1
Receiver
Sta Status LED x 1
Pow Power LED x 1
ON/OFF &
Button
Transmitter
RST Reset Button x 1
Receiver
RST Reset Button x 1
Others
Power Input
DC 12V/1A
Power
Transmitter/Receiver Max 9W
Working temperature
-5°C ~ 70°C
Working humidity
5% ~ 90%
Product Size
117 x 82 x 25 (mm)

5
Schematic diagram
Transmitter connection
1. Connect the 2 antennas to the Antenna Connector
2. Insert the power transformer into the power input hole on the front panel,
and connect the other end to the socket.

6
3. Connect the HDMI cable to the HDMI-in port of a computer or other player.
If the transmitter needs to be connected to another display, connect the HDMI
cable to the HDMI-Out port.
Receiver connection
For Steps 1 and 2 Antenna and power connection are the same as the
transmitter, please refer to the above transmitter connection steps.
3. Connect the HDMI cable to HDMI-Out of the TV, monitor and other display
to complete the connection.
Infrared booster transmitter/receiver connection
Connect the IR booster transmitter to the IR-Out port of the HDMI transmitter,
and the other end to the IR receiver of the player (please refer to the player's
user manual for the location of the IR receiver);
The infrared booster receiver is connected to the IR-In port of the HDMI
receiver, and the other end is fixed in a position where the IR controller is
visible.
HDMI transmitter and receiver pairing
1. Connect the transmitter and receiver to the power supply, connect the
HDMI input interface of the transmitter to the HDMI transmission line, and
connect the other end directly to the HDMI output interface of the receiver.
2. When the Sta working status indicator is on, press the Reset button on the
transmitter, then press the Reset button on the receiver.
3. If the Sta working status indicators of the transmitter TX and the receiver
RX flash at the same time, the pairing is completed.

7
4. Safety instructions
Please follow the following safety instructions to use this product:
⚫Do not expose the device to rain, moisture and liquids
⚫Do not put anything in the device
⚫Do not repair the device or open the case without a professional guide to
avoid electronic shock
⚫Ensure good ventilation to avoid overheating damage to the product
⚫The power transformer only uses DC 12V, if you use a third-party
transformer, please make sure the specification is the same as the
specified transformer
5. FAQs
Problems
Solutions
The power light is off
⚫Make sure the power transformer is connected
correctly.
⚫Make sure the power supply is not interrupted.
The display shows
"Searching..." for a
long time
⚫Check if the transmitter is turned on.
⚫Check that the transmitter is connected
correctly.
No video or poor video
quality
⚫Check if the connectors and transmission
cables are damaged, and make sure they are
properly connected to the corresponding
interfaces.
⚫Check if the receiver is properly connected to
the display device.
⚫Make sure all equipment is within acceptable
distance.
Infrared remote control
not responding
⚫Check whether the infrared booster and
infrared receiver are connected correctly.
⚫Check that the infrared booster and infrared
receiver are firmly inserted into the right port.

8
6. Warranty Card

9
7. Declaration of the Presence Condition of the Restricted
Substances Marking
I hereby ensure that “the presence conditions of the restricted
substance” provided above have been proved by testing or
appropriate quality control measures, and make sure the relevant
documents provided are correct and ready. Also, I agree to
cooperate with BSMI, as the Article 49 of the Commodity Inspection
Act stipulates, to provide the relevant documents, if needed, for
verification within 28 working days when BSMI carries out the market
surveillance activities.
Official website: https://www.nugenstech.com
Email: [email protected]
設備名稱 Equipment name：HDMI 無線傳輸器，型號（型式）Type designation (Type)：NW-200TR
單元Ｕnit
限用物質及其化學符號
Restricted substances and its chemical symbols
鉛Lead
(Pb)
汞Mercury
(Hg)
鎘Cadmium
(Cd)
六價鉻 Hexavalent
chromium(Cr+6)
多溴聯苯
Polybrominated
biphenyls(PBB)
多溴二苯醚
Polybrominated diphenyl
ethers(PBDE)
外殼
○
○
○
○
○
○
天線連接組件
○
○
○
○
○
○
電路板組件
○
○
○
○
○
○
其它固定組件
( 螺絲
)
○
○
○
○
○
○
備考 1.〝超出 0.1 wt %〞及〝超出 0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準值。
Note 1：“Exceeding 0.1 wt %”and “exceeding 0.01 wt %”indicate that the percentage content of the restricted substance exceeds the reference
percentage value of presence condition.
備考 2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。
Note 2：“○” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
備考 3.〝－〞係指該項限用物質為排除項目。
Note 3：The “−”indicates that the restricted substance corresponds to the exemption.