nvent CJ6STS User manual

Application
Ref. NEC Article 300-4d.
Sizing Chart
Part
Number
Cable
Type
Cable Size
Cables
Per
Fastener
Description
Box
Quantity
CJ6STS
Non-Metallic
Sheathed
Cable
(Romex), Flat
14-2, 12-2,
10-2, 14-3,
12-3 and
10-3
w/ground
8-2 and 6-2
w/ground
6 MAX
To attach
Non-Metallic
Sheathed
Cable
(Romex),
AC, BX, and
MC Cable
to Metal
Stud
100
4 MAX
Metal Clad
(MC) Cable
14-2, 12-2,
10-2, 14-3,
12-3, 10-3,
14-4, 12-4,
and 10-4
w/ground
4 MAX
Armored
Cable (AC)
14-2, 12-2,
10-2, 14-3,
12-3, 10-3,
14-4, 12-4
and 10-4
w/ground
4 MAX
Flexible Metal
Conduit (BX)
3/8 4 MAX
TECHNICAL SUPPORT:
www.nVent.com
CFS566_B
INSTRUCTION SHEET
1 OF 2
© 2019 nVent All Rights Reserved


WARNING:
nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at 1.
www.nVent.com and from your nVent customer service representative.
nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings. 2.
All instructions must be completely followed to ensure proper and safe installation and performance. 3.
Improper installation, misuse, misapplication or other failure to completely follow nVent's instructions and warnings may cause product malfunction, property 4.
damage, serious bodily injury and/or death, and void your warranty.
Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment. 5.
All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any 6.
other purpose.
NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.
The customer is responsible for:
a. Conformance to all governing codes.
b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified
engineer.
c. Using appropriate industry standard hardware as noted above.
SAFETY INSTRUCTIONS:
All governing codes and regulations and those required by the job site must be observed.
Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are
owned by nVent or its global affiliates. All other trademarks are the property of their respective owners. nVent reserves the
right to change specifications without prior notice.

1. Hook tabs on return lip of open side stud
Tip: Use arrows to align
fastener at marked heights
2. Rock fastener toward closed side of stud
NO screws required!
3. Install cables
4. Fold fastener closed.
Insert tab in hole
5. Fold tab as shown to
latch fastener closed.
5. Optional: For a snug grip on the cables, crimp the fastener with pliers.
*For wider than standard 1-1/4" studs
Unbend fastener as shown and install to stud with a screw
TECHNICAL SUPPORT:
www.nVent.com
CFS566_B
INSTRUCTION SHEET
2 OF 2
© 2019 nVent All Rights Reserved
nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are
owned by nVent or its global affiliates. All other trademarks are the property of their respective owners. nVent reserves the
right to change specifications without prior notice.