NXP Semiconductors MPC-LS-VNP-EVB User manual

Part Number Here
QuickStartGuide
AnadvancedautomotivegatewaysolutionusingNXP's
MPC5748G gatewaymicrocontrollerandLS1043A
communicationsprocessorSoCs
MPC-LS-VNP-EVB
MPC-LS-VNP-EVB

1
Quick Start Guide
GET TO KNOW THE MPC-LS-VNP-EVB
CAN 6x2
TJA1048
FlexRay x 2
Power
Supply
PCIe x 16
Connector
TJA1044 x 2
MPC2542 x 2
MPC-LS
Processor
Module
Figure 1: Front side of MPC-LS-VNP-EVB
LIN x 4
SEGMII ENET
RGMII ENET
MII ENET
RGMII_B
RGMII_C
RGMII_C

2
Quick Start Guide
MPC-LS PROCESSOR MODULE
Figure 1: Front side of MPC-LS-VNP-MOD
Power
Socket
DS1
DS2
MPC5748G Reset
MPC5748G
DS3
PPC JTAG
MPC5748G Reset
LS JTAG
J30
SJA1105S
Micro SD Card
Slot
Ethernet Port
Micro USB Port

3
www.nxp.com
MPC-LS-VNP-EVB
The NXP MPC-LS VNP EVB brings an advanced automotive gateway solution using
NXP's MPC5748G gateway microcontroller and LS1043A communications processor
SoCs. The combination of a real-time microcontroller with microprocessor application pro-
cessing enables new gateway use cases and Service-oriented Gate-ways. The complete
MPC-LS VNP EVB solution consists of two boards - a Processor Module and a Platform
Board with a wide array of automotive interfaces. The modular design of the MPC-LS VNP
EVB enables the processor module to be swapped out in the future to support future
gateway solutions using the same platform board.

4
Quick Start Guide
MPC-LS-VNP-EVB FEATURES
MPC5748G Automotive Microcontroller
•MPC-LS-VNP-EVBAEC-Q100, Grade 2
•ISO 26262 ASIL B Functional Safety
•Processors
–(2x) Power Architecture® e200z4 @160 MHz
–(1x) Power Architecture® e200z2 @ 80 MHz
•6 MB embeddedflash, 768KB SRAM
•8x CAN FD (12x w/SPI expansion)
•2x AVB Ethernet (w/switch)
•2x FlexRay, 7x LIN
•Embedded Hardware Security Module
(HSM)
–Supports SHE and EVITA standards
PMICs
•PF0100 + PF5024
•Configurable and programmable outputs to
power the core processor, memory and a
wide range of peripherals
SJA1105A Automotive Ethernet Switch
•AEC-Q100, Grade 2
•5 ports, each configurable as MII, RMII,
RGMII
Hardware
LS1043A Layerscape Microprocessor
•(4x) Arm® Cortex-A53 64-bit processors
–Up to 1.6 GHz
•Gigabit Ethernet Packet Forwarding
Engine
•10 Gbps Crypto Acceleration
•DDR3L/4 @ up to 1.6 GT/s
•4 GB DDR
•Up to (4x) 1 Gb Ethernet, 10 Gb option,
IEEE 1588
•PCI Express® Gen2 Controller
•USB 3.0
SJA1105A Automotive Ethernet Switch
•AEC-Q100, Grade 2
•5 ports, each configurable as MII, RMII,
RGMII
Software
MPC5748G: AUTOSAR, MCAL, Baremetal
LS1043A: Linux, fast path packet forwarding
Inter-Processor Communications (IPCF)

5
www.nxp.com
Connect power supply to power
socket and micro USB cable to micro
USB port on the MPC-LS Processor
Module. Make sure the DS1 and DS2
LEDs for voltage levels 5V and 3V3
respectivelyare glowing on the board.
Connect the Power
Supply
Install the FTDI CDM v2.12.28 WHQL
driver as below:
Download the driver from FTDI Driver
Connect the micro USB cable from
MPC-LS Processor module to your
Windows machine.
Go to the Device Manager and right-
click the COM port detected and
select Update Driver Software.
Select Browse my computer for driver
software and select the FTDI driver
that has been downloaded.
Restart your machine.
Install FTDI Driver
1
2
STEP-BY-STEP INSTRUCTIONS
Open Tera Term on Windows PC.
Select the serial port to which the
micro USB of the MPC-LS Processor
Module is connected and click OK. Go
to SetupSerial Port and select
115200 as the baud rate.
Setup Tera Term
Console
Press the LS reset button on the
MPC-LS Processor Module. Do not
press any key while the counter goes
down from 10 to 0. Enter “root” as
login and press Enter.
Reset the Board
3
4
The getting started IPCF application is
auto executed on login.
Application Startup
5

6
Quick Start Guide
Jumper
Option
Setting
Description
J28
UART to
USB Rx
pin
1-2
LS
1043A console
J29
UART to
USB Tx
pin
1-2
LS
1043A console
Lorem Ipsum
Dolor XXX X-X Ut a conectem rum utem enis sunt volorib eatemoluptat
DEFAULT JUMPER SETTINGS

7
www.nxp.com
MPC-LS-VNP-EVB Block Diagram

www.nxp.com
NXP and the NXP logo are trademarks of NXP B.V. All other product or service names are the property of their
respective owners. © 2016 NXP B.V.
SUPPORT
Visit www.nxp.com/support for a list of
phonenumbers within your region.
WARRANTY
Visit www.nxp.com/warranty for complete
warranty information.
Get Started
Download installation software
and documentation under
“Jump Start Your Design” at
nxp.com/XXXXXXXXX.
Document Number: XXXXXXXXX REV 0