ObboMed HO-2200 User manual

1
Your healthy living center
www.obbomed.com
Moon Sensor Light
Model No.: HO-2200
EXPLANATION SYMBOLS
Please carefully read through this manual before first use, and store it in safe place.
If you pass the product to another person, hand over this manual along with it!
INTENDED USE OF PRODUCT
- Use the device only for its intended use described in the manual.
- This product is designed for family use only, not recommended for commercial purpose.
- This product is intended for use in indoor and outdoor area.
- Moon Sensor Light only turns on in complete darkness.
- This is recommended for hallways, stairways, steps, bathrooms, bedrooms, closets, garages, acs and
basements in a convenient locaon and it won't get in your way.
- This safety-based light is designed to automacally light up dangerously dark areas, like basements or
acs, to prevent tripping and falling in the dark.
SAFETY & INSTALLATION INSTRUCTION
Baery assembling advices
- Please use only new alkaline or lithium AA baeries with 1.5V rang.
- Do not mix old and new baeries together.
- Install baeries with polarity in correct posion (see Installaon Instrucon).
- The light will be dimmer when it is going to run out of baery.
- Please keep this product out of reach of children or babies.
- Close supervision is necessary when this appliance is used by, on or near children or those with limited
dexterity or mobility.
SCOPE OF DELIVERY (ACCESSORIES)
- Moon Sensor Light
- 2 screws and 2 anchors
- Double-side tape
- User’s manual
DANGER: Warning of risk of serious injury or health hazards
WARNING: Warning of risk of injury or health hazards
CAUTION: Safety informaon about possible damage to appliance/ accessories
NOTE: Important informaon
All below informaon serves to protect the health of users and the health of other people.
Also protects the product from any damage while using.

2
APPLIANCE DESCRIPTION & OPERATION
BEFORE YOU MOUNT YOUR LIGHT:
1) Remove mounng bracket from back side of light. Open baery cover by taking out 2 thumb screws, see Fig. 1.
2) Insert 4 AA baeries (not included) according to correct polarity.
3) Close baery cover and fasten 2 thumb screws.
HOW TO USE:
Aer mounng the moon sensor light, it is ready to use.
The light automacally turns off aer 15 seconds of no moon detected.
TECHNICAL DATA & MATERIAL
Name: Moon Sensor Light
Model no.: HO-2200
Item Weight: 120g (baeries are not included )
Product Dimensions: 10 x 8.3 x 3 cm/ 3.9 x 3.3 x 1 inches
Material: ABS
Baeries: 4 AA baeries (not included)
MOUNTING WITH TAPE (INDOOR ONLY):
1) Aached double-sided tape (included) to the back of mounng bracket, see Fig. 2.
2) Aach mounng bracket to wall. Aach the main unit to mounng bracket.
MOUNTING WITH SCREWS (FOR INDOOR OR OUTDOOR USE):
1) Drill 2 holes, diameter 0.6 to 0.7cm and depth 3 cm in the wall.
2) Put anchors into the holes and align the mounng bracket and fasten the screws.
3) Aach the main unit to the mounng bracket, Fig. 4.
Use only new alkaline or lithium AA baeries with 1.5V rang. Don’t mix
old and newbaeries. Install baeries with polarity in correct posion
The light takes approximately 10 second to acvate once baeries are
inserted.
The light only turn on when it is dark and only when moon is detected.
Baery Cover
Fig. 1
Double Sided Tape
Mounng Bracket (Back)
Fig. 2
Fig. 4
Mounng Bracket (Front)
Holes for screws
Fig. 3
Loop on the back
of the main unit
Hook
Technical specificaons are subject to change without noce.

3
Distribuon by ObboMed Group:
Webshop: www.obbomed.com
Europe:
Morseweg 11, 8503 Ah Joure
The Netherlands
Mail: [email protected]
United States:
1210 E Lexington Ave,
Pomona, CA 91766, U.S.A.
Mail: [email protected]
Australia:
39/3 Kelso Crescent Moorebank,
NSW 2170, Australia
Mail: [email protected]
ObboMed® is registered Trademark of ObboMed Group.
DISPOSAL
Disposal of packing and product aer end of lifeme.
Deliver all packing materials at a collecon point or in the appropriate bins for recycling.
For further quesons, please contact the authorized disposal locaon of the public authority.
WARRANTY
The statutory warranty period applies. If the product is defecve, please contact the manufacturer's service centre
(see service e-mail at the end of this manual) or your retailer. For repair and warranty processing, please include the
following documents when you send in the product:
• A copy of the receipt with purchasing date.
• A reason for the claim or descripon of the fault.
No guarantee is provided when the product is not installed/ operated according to this manual,
used for other purposes or careless use of the product.
DISTRIBUTION & SERVICE
PRODUCT FEATURES
- IP44 Water resistant, suitable for indoor and outdoor use.
- Moon sensor combined with a light sensor allows light to be turned on only when it is dark and only when moon is
detected.
- Moon sensor for auto-On up to 15 feets with 120 degree angle.
- Auto-off aer 15 seconds of no moon detected for baery life conservaon.
- 10 limens of Super-bright white light.
- Power by 4 AA baeries (not included).
- Simple installaon, no hard-wiring and no electrician needed
- 2 mounng opons: use 2 screws or double sided tape (included)
CARE & STORAGE INSTRUCTION
In the unlikely event of product malfuncon, stop using immediately.
Please contact the local dealer for repair. Any tampering voids warranty.
- Wipe off the dust on the sensor regularly with clean water and so clothes
- Do not clean with abrasive cleaners
- Remove the baeries if the product is not used for a long me.