Octave TouchTunes Fusion DIY User manual

About This Guide
This guide is intended for Fusion jukebox Operators and technicians, as well as TouchTunes field services.
Topics
•Assumptions
•Fusion Jukebox Weight and Dimensions
•Fusion DIY Enclosure Bracket
•Required Dimensions for the Fusion DIY Enclosure
•Important Design and Installation Considerations
•Heat and Airflow Clearance Warnings
•Electrical and Wiring Warning
•Weight Restrictions
•Assembly of the Fusion DIY Enclosure Bracket
•Installation of the Fusion DIY Enclosure
•Disclaimers
•Jukebox Warranty
•Disclaimer
•Limitation of Liability
•Disclosure
Assumptions
It is assumed that:
• You have a Fusion jukebox before you start the design of its DIY enclosure.
• You have the Fusion DIY Enclosure Bracket Kit (P/N 600308-001).
• You have installed the Fusion jukebox using the Fusion Installation and Setup Guide (P/N 901095-001) prior
to the installation of its DIY enclosure.
• You have the three wing bolts (P/N 200302-001) provided from the Fusion Accessory Kit (P/N 600299-001).
Such Accessory Kit is shipped with the Fusion jukebox.
Fusion DIY Enclosure User Guide
August 2019
901097-001
Rev 00

2 Fusion DIY Enclosure User Guide
Fusion Jukebox Weight and Dimensions
Fusion Jukebox Weight and Dimensions
These tables show the weight and dimensions of the Fusion jukebox.
Fusion jukebox dimensions (in inches)
Fusion Jukebox Weight
Fusion jukebox (with no Modular Hardware Platform) 47 lbs (21.32 kg)
Wall bracket 5 lbs. (2.26 kg)
Modular Hardware Platform 18 lbs. (8.16 kg)
Fusion Jukebox Dimensions
Width Height Depth
Fusion jukebox 19 in. (48.14 cm) 19.9 in (50.55 cm) 12.7 in (31.63 cm)

3Fusion DIY Enclosure User Guide
Fusion DIY Enclosure Bracket
Fusion DIY Enclosure Bracket
The Fusion DIY Enclosure Bracket Kit is shipped with the following metal bracket pieces (which must be
assembled as follows).
Fusion DIY Enclosure Bracket Kit
The Fusion DIY Enclosure Bracket Kit is shipped with this document (P/N 901097-001).

4 Fusion DIY Enclosure User Guide
Required Dimensions for the Fusion DIY Enclosure
Required Dimensions for the Fusion DIY Enclosure
The following shows the dimensions of the Fusion DIY Enclosure Bracket (over which your Fusion DIY enclosure
must be installed). These are the minimum required dimensions for your Fusion DIY enclosure.
Fusion DIY Enclosure Bracket dimensions

5Fusion DIY Enclosure User Guide
Important Design and Installation Considerations
Fusion DIY Enclosure Bracket screw holes and slots
Important Design and Installation Considerations
• Screw holes highlighted in green in the previous figure are required to be installed. Therefore, your Fusion
DIY Enclosure must be designed, built, and installed accordingly. However, it is recommended to make use
of as many mounting points as possible (in addition to the required mounting points).
• It is not recommended that you make the top of your Fusion DIY Enclosure flat as patrons may place objects
such as bottles or glasses on it which can incur damage to the Fusion jukebox.
• The Fusion jukebox must be installed according to the instructions provided in the Fusion Installation and
Setup Guide.
• The Fusion DIY Enclosure must be designed and installed according to the requirements in this document
and according to the location’s local building codes and any other applicable requirements.

6 Fusion DIY Enclosure User Guide
Important Design and Installation Considerations
Heat and Airflow Clearance Warnings
Ventilation opening on the Fusion jukebox (top view)
Electrical and Wiring Warning
IMPORTANT: Adding lighting to the Fusion DIY Enclosure is not supported at this time.
IMPORTANT: Complete electrical and safety requirements appear on product labels located within the Fusion
jukebox.
Weight Restrictions
The Fusion DIY Enclosure for the Fusion jukebox must not weigh more than 25 lbs (11.4 kg). Do not allow any
more than this weight to rest on the Fusion jukebox. If your enclosure weighs more than this recommended
weight, then it must be wall mounted according to any applicable local building codes in addition to the wall-
mounting procedure found in the Fusion Installation and Setup Guide.
ATTENTION: Do not obstruct the top and bottom vents on the Fusion jukebox.
Your Fusion DIY Enclosure must allow for space above and below the top and
bottom vents and for at least 1 inch of space from the wall.

7Fusion DIY Enclosure User Guide
Assembly of the Fusion DIY Enclosure Bracket
Assembly of the Fusion DIY Enclosure Bracket
1. Fasten the metal support piece to the bracket using the four screws provided in the Fusion DIY Enclosure
Bracket Kit.
Fasten bracket screws
2. Fasten the shoulder screw to the bottom part of the bracket as follows.
Fasten shoulder screw

8 Fusion DIY Enclosure User Guide
Installation of the Fusion DIY Enclosure
Installation of the Fusion DIY Enclosure
1. Install the assembled bracket within the Fusion DIY Enclosure. The following shows a sample enclosure.
Bracket within a sample enclosure
2. Fasten the bracket to the enclosure using as many mounting points as possible. The minimum required
mounting points are the 4 screw holes at the bottom of the bracket and the 6 screw holes at the very top of
the bracket (see figure Fusion DIY Enclosure Bracket screw holes and slots).
3. Ensure that the Fusion jukebox door is locked.
4. Unlock the Fusion jukebox screen and remove the key from the lock.

9Fusion DIY Enclosure User Guide
Installation of the Fusion DIY Enclosure
5. Slide the Fusion jukebox screen up slightly from its bottom panel and then lift it out.
6. Set the two L brackets on the Fusion jukebox to the locked position to ensure the screen is secured in the
upright position.
Securing the screen in the upright position
CAUTION: Be careful not to pinch your fingers when opening the screen L
brackets in the next step.

10 Fusion DIY Enclosure User Guide
Installation of the Fusion DIY Enclosure
7. Place the assembled bracket/enclosure over the Fusion jukebox so that the screen passes through the
opening at the center of the enclosure. The following shows a sample enclosure.
Place enclosure over the Fusion jukebox

11Fusion DIY Enclosure User Guide
Installation of the Fusion DIY Enclosure
8. Align the metals struts of the bracket with the metal plates located on top of the Fusion jukebox as you slide
the enclosure into place. The following shows the position of the bracket on the Fusion jukebox chassis
without the enclosure as a visual example only.
Position of bracket on bare Fusion jukebox
9. Make sure that the striker bracket located at the bottom interior of the assembled bracket/enclosure connects
with the rotary latch on the front of the Fusion jukebox. The bill acceptor slots must align with the slots
(openings) on the assembled bracket/enclosure.
10. Locate the three wing bolts (P/N 200302-001) provided with the Fusion Accessory Kit.
Wing bolts from the Fusion Accessory Kit

12 Fusion DIY Enclosure User Guide
Installation of the Fusion DIY Enclosure
11. Secure the Fusion DIY Enclosure to the Fusion jukebox by hand-tightening the three wing bolts to the top
interior of the Fusion jukebox (the location for each wing bolt is circled in green in the following figure).
Location for wing bolts (interior of the Fusion jukebox)
12. Close and lock the Fusion jukebox screen.
13. For first time install of the Fusion jukebox, return to the Fusion Installation and Setup Guide to complete the
installation and setup procedures.

Copyright © 2019 The Octave Music Group, Inc. (formerly known as TouchTunes Interactive Networks, Inc.)
The Octave Music Group, Inc.
7250 Mile End, Suite 202
Montreal, Quebec,
Canada, H2R 3A4
The Octave Music Group, Inc.
850 Third Ave, 15th Floor
New York, NY 10022
USA
Technical Support
888-338-5853
www.touchtunes.com
13Fusion DIY Enclosure User Guide
Disclaimers
Disclaimers
Jukebox Warranty
The Octave Music Group, Inc. provides a separate product warranty for the Jukebox. Installation and use of the
Fusion DIY Enclosure Bracket Kit (the “Kit”) in strict accordance with this Fusion DIY Enclosure User Guide (the
“Guide”) shall not void the applicable Jukebox warranty. Notwithstanding the foregoing, other acts or omissions
of you, your personnel and your subcontractors may void the Jukebox warranty, including without limitation (a)
installation of the Kit not in compliance with this Guide; (b) operation or use of the Kit not in compliance with this
Guide; (c) unauthorized repair or modification of the Kit or the Jukebox; or (d) any other misuse, abuse or
mishandling of the Kit or the Jukebox. You are advised to review this Guide and the terms of the Jukebox
warranty before installing, operating or using the Kit.
Disclaimer
THE KIT AND ANY RELATED COMPONENTS OR ACCESSORIES ARE PROVIDED “AS IS” AND WITHOUT
ANY WARRANTIES OF ANY KIND. INSTALLATION, OPERATION AND USE OF THE KIT IS AT YOUR OWN
RISK. THE OCTAVE MUSIC GROUP, INC. DOES NOT MAKE, AND HEREBY DISCLAIMS, ANY AND ALL
WARRANTIES WITH RESPECT TO THE KIT, WHETHER EXPRESS, IMPLIED, STATUTORY OR
OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NONINFRINGEMENT, AND ANY WARRANTIES
ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE. THE OCTAVE MUSIC GROUP,
INC. DOES NOT WARRANT THAT THE KIT WILL OPERATE WITHOUT INTERRUPTION OR WILL BE
DEFECT-FREE, OR THAT THE KIT WILL MEET YOUR REQUIREMENTS.
Limitation of Liability
IN NO EVENT SHALL THE OCTAVE MUSIC GROUP, INC. BE LIABLE TO YOU OR TO ANY THIRD PARTY
FOR ANY DIRECT OR INDIRECT LABOR COSTS, FOR ANY LOSS OF PROFITS, SALES, BUSINESS OR
DATA, OR FOR ANY OTHER INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES, WHETHER ARISING IN CONTRACT, TORT, OR STRICT LIABILITY, EVEN IF
THE OCTAVE MUSIC GROUP, INC. HAS BEEN INFORMED OF, KNEW OF, OR SHOULD HAVE KNOWN OF
THE LIKELIHOOD OF SUCH DAMAGES. IN NO EVENT SHALL THE OCTAVE MUSIC GROUP, INC.’S
LIABILITY ARISING OUT OF OR RELATED TO THE KIT OR ANY INSTALLATION, OPERATION OR USE OF
THE KIT EXCEED THE AMOUNT PAID BY YOU FOR THE KIT, AS EVIDENCED BY THE ORIGINAL INVOICE.
Disclosure
SOME JURISDICTIONS MAY NOT ALLOW CERTAIN DISCLAIMERS OR LIMITATIONS AS MAY BE SET
FORTH IN THIS GUIDE AND SUCH DISCLAIMERS OR LIMITATIONS MAY NOT APPLY.
Popular Enclosure manuals by other brands

Conrad
Conrad 41 35 05 operating instructions

EMC2
EMC2 TAE Disassembly instructions

Macpower & Tytech
Macpower & Tytech Clearlight User manual & installation guide

Martin Audio
Martin Audio Wavefront W8CT Specification sheet

Hamlet
Hamlet USB 3.0 STORAGE STATION user manual

Ultra Products
Ultra Products ATX Cases Defender Specification sheet