OEM Tools 24861 Service manual

Operating Instructions and Parts Manual 24861
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
[email protected]
WASTE OIL DRAIN
112/18
2018 OEMTOOLS™
The following safety information is provided as a guideline to help you operate your Waste Oil Drain under the safest possible
conditions. Any tool or piece of equipment can be potentially dangerous to use when safety or safe handling instructions are
not known or not followed. The following safety instructions are to provide the user with the information necessary for safe use
and operation. Please read and retain these instructions for the continued safe use of your Waste Oil Drain. Failure to follow
instructions listed below may result in serious injury. In addition, make sure that anyone who uses the equipment understands
and follows these safety instructions as well.
Thank you very much for choosing an OEMTOOLS™Product!
For future reference, please register your new tool at www.oem-tools.com and complete the owner’s record below:
Model: _______________ Purchase Date: ___________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product
before you begin using it. This product is designed for certain applications only. OEMTOOLS™cannot be responsible for issues
arising from modification. We strongly recommend that this product is not modified and/or used for any application other than that
for which it was designed. If you have any questions relative to a particular application, DO NOT use the product until you have first
contacted customer service to determine if it can or should be performed on the product.
WARNING:This product can expose you to chemicals, including DEHP, which are known to the State of California to
cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
EXPLANATION OF SAFETY SIGNAL WORDS
WARNING:Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION:Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION:Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
NOTES:Provide clarity and helpful information.
WARNING
UNPACKING
After unpacking the unit, inspect carefully for any damage that
may have occurred during transit. Check for loose, missing,
or damaged parts. If any damage is observed, a shipping
damage claim must be filed with the carrier. DO NOT use
the OEMTOOLS™ 24861 Waste Oil Drain if broken, bent,
cracked or damaged parts (including labels) are noted. Any
Waste Oil Drain that appears damaged in any way, operates
abnormally or is missing parts should be removed from service
immediately. If you suspect that the Waste Oil Drain was
subjected to shock load (a load that was dropped suddenly,
unexpectedly, etc.), immediately discontinue use until it has
been checked by a factory authorized service center.
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and
others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in personal
injury and/or damage to product or property. Please retain instructions for future reference.

2
Operating Instructions and Parts Manual 24861
12/18
2018 OEMTOOLS™
WASTE OIL DRAIN
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your tool. Read this manual carefully. Learn the tool’s
applications and limitations, as well as potential hazards specific to it.
2. Keep work area clean and well lit. Cluttered or dark work areas invite
accidents.
3. Keep children away. All children should be kept away from the work
area. Never let a child handle a tool without strict adult supervision.
4. DO NOT operate this tool if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your judgment
or reflexes are impaired while taking drugs. If there is any doubt, do
not attempt to operate.
5. Use safety equipment. Eye protection should be worn at all times
when operating this tool. Use ANSI approved safety glasses.
Everyday eyeglasses are NOT safety glasses. Dust mask, non-skid
safety shoes, hard hat or hearing protection should be used in
appropriate conditions.
6. Wear proper apparel. Loose clothing, gloves, neck-ties, rings,
bracelets or other jewelry may present a potential hazard when
operating this tool. Keep all apparel clear of the tool.
7. DO NOT overreach. Keep proper footing and balance at all times
when operating this tool.
8. Check for damage. Check your tool regularly. If part of the tool is
damaged, it should be carefully inspected to make sure that it can
perform its intended function correctly. If in doubt, the part should be
repaired. Refer all servicing to a qualified technician. Consult your
dealer for advice.
9. Keep away from flammables. DO NOT attempt to operate this tool
near flammable materials or combustibles. Failure to comply may
cause serious injury or death.
10. Store idle tools out of the reach of children and untrained persons.
Tools may be dangerous in the hands of untrained users.
11. Maintain tools with care.
12. Keep tools dry and clean.
13. Properly maintained tools are less likely to bind and are easier to
control. DO NOT use a damaged tool. Tag damaged tools “DO NOT
Use” until repaired.
14. Check for misalignment or binding of moving parts, breakage of
parts, and any other condition that may affect the tool’s operation.
15. If damaged, have the tool serviced before using. Many accidents are
caused by poorly maintained tools.
16. Use only accessories that are recommended by the manufacturer
for your model. Accessories that may be suitable for one tool may
become hazardous when used on another tool.
17. Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could
result in a risk of injury.
18. When servicing a tool, use only identical replacement parts. Use of
unauthorized parts or failure to follow maintenance instructions may
create a risk of injury.
19. Maintain a safe working environment. Keep the work area well lit.
Make sure there is adequate surrounding workspace. Keep the
work area free of obstructions, grease, oil, trash, and other debris.
DO NOT use this product in a damp or wet location.
INSTRUCTIONS SPECIFIC TO THIS PRODUCT
1. Maintain labels and nameplates on this product. These carry
important information. If unreadable or missing, contact OEMTOOLS
for a replacement.
2. Keep the handle dry, clean, and free from brake fluid, oil, and grease.
3. Before use, read and understand all warnings, safety precautions, and
instructions as outlined in the vehicle manufacturer’s service manual.
It is beyond the scope of this manual to properly describe the correct
procedure and test data for each vehicle.
4. Always perform vehicle service in a properly ventilated area. Never
run an engine without proper ventilation for its exhaust. Stop work
and take necessary steps to improve ventilation in the work area if
you develop momentary eye, nose, or throat irritation as this indicates
inadequate ventilation.
5. Engine parts that are in motion and unexpected movement of a
vehicle can injure or kill. When working near moving engine parts,
wear snug fit clothing and keep hands and fingers away from moving
parts. Keep hoses and tools clear of moving parts. Always stay clear
of moving engine parts. Hoses and tools can be thrown through
the air if not kept clear of moving engine parts. The unexpected
movement of a vehicle can injure or kill. When working on vehicles,
always set the parking brake or block the wheels.
6. Be alert for hot engine parts to avoid accidental burns.
7. If you drove your car recently, fluids could be very hot. Allow at least
2 hours before you handle any fluids. Oil and Coolant burns are very
dangerous.
8. Avoid accidental fire and/or explosion. DO NOT smoke near engine
fuel and battery components.
9. Never remove the cap from the radiator or expansion tank while the
engine is at operating temperature.
10. Always allow the engine to cool before removing the radiator cap or
expansion tank cap. The cooling system is under pressure. Failure to
allow the engine to cool before attempting to remove the cap could
result in serious injuries.
11. DO NOT misuse, over-pressurize, modify parts, or use worn and/or
damaged parts.
12. DO NOT use oil drain for flammable or caustic fluids.
13. DO NOT exceed 7 psi (0,5 bar) air pressure when emptying the oil drain.
14. The warnings, precautions, and instructions discussed in this manual
cannot cover all possible conditions and situations that may occur.
The operator must understand that common sense and caution are
factors which cannot be built into this product, but must be supplied
by the operator.
15. For safety purposes and the prevention of damage to expensive
components, it is advised that the user understand basic automotive
repair and have a working knowledge of automotive systems.
16. We believe the information contained herein to be reliable. However,
general technical information is given by us without charge and the
user shall employ such information at his or her own discretion and
risk. We assume no responsibility for results or damages incurred from
the use of such information in whole or in part. Always refer to specific
instructions and technical information supplied by vehicle manufacturer.
17. The manufacturer declines any and all responsibility for damage
to vehicles or components if said damage is the result of unskillful
handling by the operator or of failure to observe the basic safety rules
set forth in the instruction manual.
18. Used oil, antifreeze, brake fluid and transmission fluid contain
chemical compounds that can be harmful to humans and animals.
When managed properly, used oil may again be of beneficial use.
Used oil may be blended and recycled as a heating or industrial fuel
and also may be re-refined and made into new lubricants. Persons
who perform maintenance on their own vehicles are responsible
for managing the used fluids in a manner that is protective of
human health and the environment and to follow all local laws and
regulations concerning their disposal.

3
Operating Instructions and Parts Manual 24861
12/18
2018 OEMTOOLS™
WASTE OIL DRAIN
DISPOSAL
At the end of the useful life of the Waste Oil Drain, dispose of the
components according to all local, state, and federal regulations.
PURPOSE
The Waste Oil Drain is designed for the collection of used fluids
including motor oil, transmission fluid, and coolant from under lift-
mounted vehicles.
The portable oil drain system is designed to safely capture oil and
other vehicle fluids with the use of a large funnel. After use, the drain is
emptied using air pressure.
An external air supply is required to run the drain.
PRODUCT SPECIFICATIONS
Reservoir Capacity 80L (21 Gallons)
Discharge Hose Length 70"
Oil Drain Funnel Diameter 15"
Oil Drain Extension Diameter 22"
Funnel Height Adjustment 45" – 62"
Caster 3-1/2" (2 Swivel,
2 Swivel with Lock)
Max Air Pressure 7 PSI (0.5 Bar)
NOTE: Not all components of the Waste Oil Drain are replacement
items, but are illustrated as a convenient reference for location and
position in the assembly sequence.
OPERATION
CAUTION
1. This equipment is intended only for professional use by personnel
trained in performing the service functions for which it is designed.
2. This equipment is designed for servicing a variety of vehicles in a
safe, convenient manner. However, differences in vehicle makes
and models could make it impossible to use this equipment as it is
intended. DO NOT attempt to force the use of this equipment on an
application for which it is not designed to perform.
3. The procedures documented in this manual are to serve as guidelines
for the use of this equipment.
4. In addition to these guidelines, always follow the manufacturer’s
recommended procedures when servicing each unique vehicle.
5. The use of this equipment is simple and straightforward if you follow
the instructions. However, always keep in mind that you are working
with a system that may be under pressure, with fluid that is just
waiting to be expelled. When operating this equipment, use common
sense and always stop to think before disconnecting a hose or other
component.
6. Always use the Waste Oil Drain on a flat, level surface and lock the
casters before using.
Waste Oil Drain
Figure Description
1 Oil Drain Extension Diameter
2 Oil Drain Funnel Diameter
3 Pressure Gauge
4Safety Valve
5Release Valve
6Central Drain Tube
7 Air Fitting
8 Waste Oil Discharge Hose
9 Waste Oil Discharge Valve
10 Caster (with brake)
11 Caster (no brake)
12 Pressure Valve (not shown)
13 Main Valve
10
11
13
5
9
8
7
3
6
2
1

4
Operating Instructions and Parts Manual 24861
12/18
2018 OEMTOOLS™
WASTE OIL DRAIN
WARNING:DO NOT use this equipment with gasoline or other
flammable liquids or with fluids at temperatures above 175° Fahrenheit
(80° Celsius). Keep away from open flames or excessive heat.
INSTRUCTIONS
COLLECTING WASTE OIL
1. Position the Waste Oil Drain under the vehicle, adjust the bowl to the
desired height, and set the brakes on the casters.
2. Check the sight glass to ensure there is sufficient remaining capacity.
Never allow fluid to exceed the maximum level. The reservoir will not
drain if the fluid exceeds the maximum level on the sight glass.
DRAINING THE RESERVOIR
1. Raise the collecting bowl to its maximum height and set the caster
brakes. Close the pressure valve on the side of the Drain Tube.
WARNING: If valve is not closed, waste oil will shoot out of the
funnel and spray the user.
2. Secure the discharge hose to the bulk waste oil tank and open the
discharge hose valve.
3. Set the air supply to a maximum of 7 PSI (0.5 Bar).
WARNING: DO NOT exceed 7 PSI (0.5 Bar). Failure to comply
may result in serious personal injury.
4. Connect air supply to the valve stem using the air chuck tire
inflator.
5. Remove the air chuck from the valve stem when the desired flow
rate is achieved or if the safety relief valve opens.
NOTE: If flow rate stops before the drain is empty, repeat steps 3, 4, and 5.
MAINTENANCE
1. Relieve pressure or vacuum before inspecting or servicing.
2. Always store the Waste Oil Drain in a well-protected area where it
will not be exposed to inclement weather, corrosive vapors, abrasive
dust, or any other harmful elements.
3. Keep the Waste Oil Drain clean for better and safer performance.
4. Inspect the Reservoir, Hoses, Caps, Gaskets, Seals, and Gauge
periodically and, if damaged, replace them.
CONTACT US
3580 E. Raines Road, Suite 3, Memphis, TN 38118
Tel: [phone]
www.oem-tools.com
OEMTOOLS™ ONE YEAR WARRANTY
For up to one year from the date of purchase of this OEMTOOLS™ product, if you find any defect in material or workmanship (through normal
usage), return it to the place of purchase or to OEMTOOLS™ for repair or replacement at our discretion. In order to obtain this service, send the
product and proof of purchase (transportation pre-paid) to:
OEMTOOLS™ Q.A. Dept, 3580 E. Raines Road #3, Memphis, TN 38118.
We will not be responsible for lost or damaged goods during transportation; please insure your package. If our inspection verifies the defect,
we will either repair or replace the product, or we may elect to refund the purchase price if we cannot readily and quickly provide you with a
replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not
within the scope of our warranty, then you must bear the cost of returning the product.
OEMTOOLS™ does not provide warranty for products labeled other than OEM®or OEMTOOLS™. OEMTOOLS™ will not provide any warranty
for products subjected to abnormal use. Abnormal use includes (but is not limited to) abuse, accident, alteration, neglect, and unauthorized
or unreasonable use or repairs. This warranty does not cover bits, blades, files, batteries, or calibration. We recommend that you maintain
your tools and sharpen or replace blades, bits, files, and batteries as necessary. OEMTOOLS™ reserves the right to make any changes in
construction or design at any time without any obligation in incorporating such changes to tools or equipment previously sold.
OEMTOOLS™ makes every effort to ensure that its products meet high quality and durability standards, and warrants to the original purchaser
that this product is free from defects in materials and workmanship for the period of one year from the date of purchase. This warranty does not
apply to damage due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,
improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising
from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation
of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS. This warranty gives you specific legal rights, and you may also have other rights, which vary
from state to state.
Don’t forget to register your new OEMTOOLS™ product at www.oem-tools.com.