OEM Tools 24677 Service manual

UNPACKING
After unpacking unit, inspect carefully for any damage that
may have occurred during transit. Check for loose, missing,
or damaged parts. If any damage is observed, a shipping
damage claim must be filed with carrier. DO NOT use the
OEMTOOLS®Pneumatic Heated Parts Washing Cabinet if
broken, bent, cracked or damaged parts (including labels) are
noted. Any Parts Washing Cabinet that appears damaged in
any way, operates abnormally, or is missing parts should be
removed from service immediately. If you suspect that the
Parts Washing Cabinet was subjected to shock load (a load
that was dropped suddenly, unexpectedly, etc.), immediately
discontinue use until it has been checked by a factory
authorized service center.
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and
others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in personal
injury and/or damage to product or property. Please retain instructions for future reference.
The following safety information is provided as a guideline to help you operate your Parts Washing Cabinet under the safest
possible conditions. Any tool or piece of equipment can be potentially dangerous to use when safety or safe handling instructions
are not known or not followed. The following safety instructions are to provide the user with the information necessary for safe
use and operation. Please read and retain these instructions for the continued safe use of your Parts Washing Cabinet. Failure
to follow instructions listed below may result in serious injury. In addition, make certain that anyone who uses the equipment
understands and follows these safety instructions as well.
Operating Instructions and Parts Manual 24677
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
[email protected]
Thank you very much for choosing an OEMTOOLS®Product!
For future reference, please register your new tool at www.oem-tools.com and complete the owner’s record below:
Model: _______________ Purchase Date: ___________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product
before you begin using it. This product is designed for certain applications only. OEMTOOLS®cannot be responsible for issues
arising from modification. We strongly recommend that this product is not modified and/or used for any application other than that
for which it was designed. If you have any questions relative to a particular application, DO NOT use the product until you have first
contacted customer service to determine if it can or should be performed on the product.
Explanation of Safety Signal Words
WARNING:Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION:Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION:Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
NOTES:Provide clarity and helpful information.
PNEUMATIC HEATED PARTS
WASHING CABINET
1
8/19
2019 OEMTOOLS®
24677
WARNING

2
Operating Instructions and Parts Manual 24677
8/19
2019 OEMTOOLS®
PNEUMATIC HEATED
PARTS WASHING CABINET
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your product. Read this manual carefully. Learn
the product’s applications and limitations, as well
as potential hazards specific to it. The use of this
product is simple and straightforward if you follow the
instructions. When operating this product, use common
sense and only use this product for its intended
purpose.
2. Maintain labels and nameplates on this product. These
carry important information. If unreadable or missing,
contact OEMTOOLS®for a replacement.
3. Maintain this product with care. Keep it dry and clean –
and free from brake fluid, oil, and grease (if applicable).
4. Check for damage. Check your product regularly. If
part of the product is damaged, it should be carefully
inspected to make sure that it can perform its intended
function correctly. If in doubt, the part should be
repaired. Refer all servicing to a qualified technician.
Consult your dealer for advice.
5. Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the product’s operation.
6. DO NOT use a damaged product. Tag damaged
products “DO NOT USE” until repaired. If damaged,
have the product serviced before using. Many
accidents are caused by poorly maintained products.
7. Service must be performed only by qualified repair
personnel. Service or maintenance performed by
unqualified personnel could create a risk of injury.
8. When servicing a product, use only identical
replacement parts. Use of unauthorized parts or failure
to follow maintenance instructions could create a risk
of injury.
9. Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one product may become hazardous when
used on another product.
10. Keep work area clean and well lit. Cluttered or dark
work areas invite accidents.
11. Maintain a safe working environment. Keep the work
area well lit. Make sure there is adequate surrounding
workspace. Keep the work area free of obstructions,
grease, oil, trash, and other debris. DO NOT use this
product in a damp or wet location.
12. Keep children away. All children should be kept away
from the work area. Never let a child handle this
product without strict adult supervision.
13. Store this product out of the reach of children and
untrained persons. This product may be dangerous in
the hands of untrained users.
14. DO NOT operate this product if under the influence of
alcohol or drugs. Read warning labels on prescriptions
to determine if your judgment or reflexes are impaired
while taking drugs. If there is any doubt, DO NOT
attempt to operate.
15. Use safety equipment. Eye protection should be worn
at all times when operating this product. Use ANSI
approved safety glasses. Everyday eyeglasses are NOT
safety glasses. Dust mask, non-skid safety shoes, hard
hat or hearing protection should be used in appropriate
conditions.
16. Wear proper apparel. Loose clothing, gloves, neck-ties,
rings, bracelets or other jewelry may present a potential
hazard when operating this product. Keep all apparel
clear of the product.
17. DO NOT overreach. Keep proper footing and balance
at all times when operating this product.
18. Keep away from flammables. DO NOT attempt to
operate this product near flammable materials or
combustibles. Failure to comply may cause serious
injury or death.
19. Avoid accidental fire and/or explosion. DO NOT smoke
near engine fuel and battery components.
20. We believe the information contained herein to be
reliable. However, general technical information is given
by us without charge and the user shall employ such
information at their own discretion and risk. We assume
no responsibility for results or damages incurred from
the use of such information in whole or in part. Always
refer to specific instructions and technical information
supplied by vehicle manufacturer.
21. The manufacturer declines any and all responsibility
for property damage or injury if said damage is the
result of unskillful handling by the operator or of
failure to observe the basic safety rules set forth in the
instruction manual.
22. The warnings, precautions, and instructions discussed
in this manual cannot cover all possible conditions
and situations that may occur. The operator must
understand that common sense and caution are factors
which cannot be built into this product, but must be
supplied by the operator.
PRODUCT DESCRIPTION
The OEMTOOLS®24677 Pneumatic Heated Parts
Washing Cabinet uses compressed air to spray heated
cleaner (up to 140°F) for maximum cleaning effectiveness.
PRODUCT SPECIFICATIONS
Cleaning Solution Capacity 3.5 Gallons (13.25L)
Max Temperature 140°F (60°C)
Air Requirement 70-120 PSI @ 5 CFM
Flow Rate .21 GPM
CONTENTS
Washing Cabinet
Cleaning Gun
Handling Gloves
Cabinet Leveling Pads
NOTE: Cleaning Solution not included

3
Operating Instructions and Parts Manual 24677
8/19
2019 OEMTOOLS®
PNEUMATIC HEATED
PARTS WASHING CABINET
SPECIFIC SAFETY INSTRUCTIONS
AND WARNINGS
Thoroughly read and understand all instructions in this
product manual before using this product. Failure to
follow all instructions listed below may result in electric
shock, fire, and/or serious personal injury.
WARNING:
1. DO NOT use with flammable or combustible solvent.
2. DO NOT operate in locations with poor ventilation.
3. DO NOT operate with damaged gloves.
4. Always ensure that Power and Heating switches are in
the “Off” position before opening cabinet.
CAUTION:
5. DO NOT operate with cabinet lid in the open position.
6. DO NOT operate heating element with empty cleaning
solution tank. Operating with less than 2 gallons of
solvent can damage the heating element.
7. DO NOT leave Power or Heating Element “On” while
not in use.
8. Only operate on hard, level surface.
9. It is recommended to set thermostat below 120°F
(50°C).
WORK AREA SAFETY
1. Keep your work area clean and well lit. Cluttered and
dark work areas invite accidents.
2. DO NOT operate in potentially explosive environments,
such as in the presence of flammable liquids, gas, or
dust. The heating element may ignite the dust or fumes.
ELECTRICAL SAFETY
1. Use only with 120V AC GFCI outlets.
2. Avoid using extension cords whenever possible.
PERSONAL SAFETY
1. Although the washing cabinet provides protection from
the cleaning process, it is recommended to wear ANSI
approved safety googles when using compressed air or
cleaning solutions.
ASSEMBLY
1. Carefully lay the Parts Washing Cabinet (18) on a flat
surface with the Front Panel (1) facing up.
2. Attach the Support Leg Cross Brace (22) to the Support
Legs (23) using the 2 M10 bolts and flat washers.
3. Attach the Support Legs (23) to the Cabinet (18) using
4 M12 bolts and flat washers.
4. Attach the 4 Leveling Pads (24) to the Support Legs
(23).
5. With assistance, carefully stand the assembled Parts
Washing Cabinet and tighten all fasteners.
6. Using a level (not included), adjust Leveling Pads (24)
making sure that the Parts Washing Cabinet is level in
its desired location.
7. Connect an air compressor hose to the Air Inlet located
under the cabinet near the Front Panel (1). See Figure 1
Figure 1
Air Inlet
OPERATION
1. Be sure that the Power and Heating Switches are in the
“Off” positions and plug the power cord into a 120V AC
GFCI outlet.
2. With the Cabinet Cover (10) and the Front Panel (1)
open, pour cleaning solution into the fluid return inside
the cabinet while observing the Cleaner Level Indicator
on the Cleaning Solution Tank (4).
3. Place the part to be cleaned on the Metal Grate (6)
inside the cabinet and close the Cabinet Cover (10).
4. Adjust cleaning air pressure for the type of item you are
cleaning with the air pressure regulator located on the
Front Panel (1) while observing the pressure gauge also
located on the Front Panel. See Figure 2
Figure 2

4
Operating Instructions and Parts Manual 24677
8/19
2019 OEMTOOLS®
PNEUMATIC HEATED
PARTS WASHING CABINET
5. Turn on the power to the unit with the Power Switch
located on the Front Panel (1).
6. If the cleaning job does not require heated cleaning
solution, proceed to step 7. If heated cleaning solution
is needed, proceed to step 8.
7. With the Cabinet Cover (10) closed and Power Switch
“On”, use the Gloves (11) to operate the Cleaning Gun
(17) inside the cabinet. You can control the flow of
cleaning solution with the Fluid Control Valve pictured
in Figure 3. When in the closed position, the Cleaning
Gun can be used to dry the part.
Figure 3
Fluid
Control
Valve
8. To clean with heated cleaning solution:
a. Push the Heat Switch to the “On” position
b. Press the Thermostat Control power button
(marked “OK”). The current temperature setting
will display.
c. Press “Set” on the Thermostat Control; the
numbers will begin to blink.
d. Using the arrow keys, increase or decrease the
temperature to the desired setting.
e. Press “OK” to lock in the temperature setting.
Figure 4
9. Clean parts using the Cleaning Gun (17) as described in
step 7.
10. When you are done cleaning the part, turn “Off” the
Heat Switch then the Power Switch before opening the
Cabinet Cover (10) to remove the part.
CARE AND MAINTENANCE
1. Disconnect power cord and air before maintenance or
when not in use for extended periods of time. It is also
recommended to empty the Cleaning Solution Tank (4).
2. Clean regularly with mild soap and water using caution
to avoid excess water on the Front Panel (1).
3. Remove and clean the Cleaning Solution Filter (7)
located in the cleaner return below the Metal Grate (6).
4. Use the tank drain valve location on the side of the
tank to remove cleaning solution. Pour warm water in
through the cleaner return inside the cabinet with the
tank drain valve open and routed to an appropriate
drain pan or bucket in order to remove dirty cleaning
solution. The Cleaning Solution Tank (4) can be
removed for cleaning periodically by taking out the
holding screw at the front of the tank.
5. Be sure to dispose of old cleaning solution as
described by the manufacturer.
TROUBLESHOOTING
Symptom(s) Possible Cause(s) Corrective
Action(s)
Cleaning gun does
not deliver cleaning
solution with valve
fully open
1. Power switch
is “Off”
2. Cleaning
solution is low
3. Cleaning
solution
supply hose is
clogged
1. Push switch to
“On”
2. Add cleaning
solution to tank
3. Remove
supply hose
and check for
blockage
Light does not come
on with power but
fan operates
Bulb is no
longer good Replace bulb
Thermostat Control
is not displaying
correctly
Connection plug
may be loose
Check the
connection and
secure
Cleaning solution is
not heating properly
1. Heat switch is
not in the “On”
position
2. Heating
element is
damaged
1. Push Heat
switch to “On”
2. Remove and
replace heating
element
DISPOSAL
At the end of the useful life of the Heated Parts Washing
Cabinet, dispose of the components according to all
local, state, and federal regulations.

5
Operating Instructions and Parts Manual 24677
8/19
2019 OEMTOOLS®
PNEUMATIC HEATED
PARTS WASHING CABINET
1
2
3
4 5
67
11
12
16
14
18
21
13
17
20
15
19
22
23
24
Figure Description Qty.
1 Front Panel 1
2 Pin 2
3 Hinge Axis 2
4 Cleaning Solution Tank 1
5 Cabinet Holder 1
6 Metal Grate 1
7 Filter Screen 1
8 LED Light 1
9 Light Hoop 2
10 Cabinet Cover 1
11 Gloves 1 pair
12 Gloves Hoop 2
13 Back Door Rod 2
14 Fan Cover 1
15 Front Door Rod 2
16 Ventilation Fan 1
17 Cleaning Gun 1
18 Cabinet 1
19 Rear Cover 1
20 Side Support 4
21 Side Cover 2
22 Support Leg Cross Brace 1
23 Support Leg 2
24 Leveling Pad 4
PARTS LIST
PRODUCT LAYOUT
8
9
10

6
Operating Instructions and Parts Manual 24677
8/19
2019 OEMTOOLS®
PNEUMATIC HEATED
PARTS WASHING CABINET
NOTES:

7
Operating Instructions and Parts Manual 24677
8/19
2019 OEMTOOLS®
PNEUMATIC HEATED
PARTS WASHING CABINET
NOTES:

8
Operating Instructions and Parts Manual 24677
8/19
2019 OEMTOOLS®
PNEUMATIC HEATED
PARTS WASHING CABINET
CONTACT US
3580 E. Raines Road, Suite 3, Memphis, TN 38118
Tel: [phone]
www.oem-tools.com
OEMTOOLS®90 DAY LIMITED WARRANTY
For up to 90 days from the original purchase of this OEMTOOLS®product, if you find any defect in material or
workmanship (through normal usage), return it to the place of purchase or to OEMTOOLS®for repair or replacement at
our discretion. In order to obtain this service, send your tool and proof of purchase (transportation pre-paid) to:
OEMTOOLS®Q.A. Dept., 3580 E. Raines Road #3, Memphis, TN 38118.
We will not be responsible for lost or damaged goods during transportation; please insure your package. If our
inspection verifies the defect, we will either repair or replace the product, or we may elect to refund the purchase price
if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if
we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you
must bear the cost of returning the product.
OEMTOOLS®does not provide warranty for products labeled other than OEM®or OEMTOOLS®. OEMTOOLS®will
not provide any warranty for products subjected to abnormal use. Abnormal use includes (but is not limited to) abuse,
accident, alteration, neglect, and unauthorized or unreasonable use or repairs. This warranty does not cover bits,
blades, files, batteries, or calibration. We recommend that you maintain your tools and sharpen or replace blades, bits,
files, and batteries as necessary. OEMTOOLS®reserves the right to make any changes in construction or design at any
time without any obligation in incorporating such changes to tools or equipment previously sold.
OEMTOOLS®makes every effort to ensure that its products meet high quality and durability standards and warrants
to the original purchaser that this product is free from defects in materials and workmanship for the period of 90
days from the date of purchase. This warranty does not apply to damage due directly or indirectly to misuse, abuse,
negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear
and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or
consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY
IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS. This warranty gives you specific legal rights, and you may also have other rights,
which vary from state to state.
Don’t forget to register your new OEMTOOLS®product at www.oem-tools.com.