Ofuzzi Cyber User manual

Cyber
Thank you for purchasing Ofuzzi Cordless Robotic Pool Cleaner
If you have any questions or issues, please contact us for customer service.
User Manual
Cordless Robotic Pool Cleaner

Table of Contents
Important Precautions
I. Introduction
II. Appearance&structure
III. Specifications
IV. Operation instruction
V. Trouble shooting
VI. Packing list
VII. Warranty
- 01 -
02
04
05
06
07
14
15
15

Important Precautions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Do not power on the cleaner when it is out of the water.
Strictly prohibit using the cleaner beyond its operating conditions. Please read the manual carefully, and use it according to the manual.
We have no responsibility for any loss or injury caused by improper use.
Use the accessories recommended or sold by the manufacturer only.
This model mainly applies to swimming pools with a flat floor.
The cleaner should not be used by children under the age of 8 or people with mental disorders. Please do so under the supervision of
the guardian if necessary. Please do not allow children to ride on it or play as a toy.
Use the original and authorized power adapter only.
It must be replaced by the after-sale professionals if the power line is damaged.
The power line must be connected to a leakage protected and earthed socket when charging.
Do not operate the cleaner when there are people in the pool.
Always clean and wash the filter tray after use.
Power off the cleaner when maintaining, cleaning or not using it.
The cleaner should be stored in a cool and ventilated place, away from direct sunshine.
Charge the battery under the permitted condition. The cleaner should be stored in a cool place when charging, meanwhile do not
place or be covered with anything to prevent the damage of internal electrical components caused by overheating of the power unit.
Only professionals can disassemble the sealed driving kit of the cleaner.
Close the pool filtration system before use.
The cleaner should be charged every three months if it needs to be stored for a long time. Please use the original and authorized
adapter only to ensure that the battery power is maintained at 40%-60%. The battery voltage will be lower than the over-discharge
protection voltage due to the self-discharge of battery if not charging the battery for a long time, which will lead to fatal damage to the
battery if continuing too long. Please be careful.
Prohibit charging the battery under the condition of fire or extreme heat. Do not use or store the cleaner near the heat source.
Prohibit piercing the cleaner shell with nails or other sharp objects, and prohibit hammering, impacting and throwing the cleaner.
I.
The robotic pool cleaner Cyber is a new type of rechargeable automatic cleaning equipment for pools with the function of automatic
beaching.
The cleaning function is upgraded, and the half-way turn-back function is activated for 5-12 times every 20 times the wall is hit, so that
the center of the swimming pool is no longer a dead corner for cleaning.
Introduction III.Specifications IV.
1.
a.
b.
Operation instruction
Precautions
Install the brush before use to avoid possible dirt leaks.
Please ensure that the top cover of the cleaner is tightly assembled to its chassis.
c.
d.
e.
f.
g.
After turning on, the cleaner must be placed in the pool within 20 seconds
Put into or lift out of the pool with the cleaner bottom towards the wall to avoid any possible scratches to the pool.
Power off the cleaner after use.
Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting into or lifting out of the pool.
It is necessary to stay on the water surface for 10-15 seconds until water flows out from the cleaner to the pool before being placed on the ground.
g.
2.
a.
*
*
*
b.
*
Lift the handle or clips of the cleaner out from the pool.
Quick operation
Plug in the cleaner with the supplied adapter and charging line to charge the battery.
Turn the switch knob to OFF before charging.
Clean the charging port before charging.
Keep the machine charging port and the adapter dry when charging.
Turn the switch knob to power on or off the cleaner
Please put into water within 20 seconds after turning on.
c.
d.
e.
3.
There are two nozzles on the cleaner, one of them opens once the other closes. Water flows out through the open nozzle to thrust the
cleaner forward. Adjust the nozzle by turning it to control the cleaner route.
Turn the switch knob to ON, the cleaner is power-on and the indicator light is steady blue, then put it into water. About 15 seconds after
power-on, the cleaner begins to work, and the blue light flashes.
When battery power is low, the cleaner will move close to the pool wall. The red-light fast flashes. The cleaner stops running when it
runs out of battery.
Indicators
Functions and adjustment of nozzles
a.
The nozzles of the cleaner are marked with angles (0°-40°).
The cleaner moves in an approximately straight line when the nozzle angle is 0°.
The cleaner moves in a more curved line at a larger angle from 0°-40°.
Setting 1: default setting: 0°-20°, for most of pools.
Setting 2: 0°-40°, when setting 1 does not manage a full coverage of the pool.
Setting nozzle angle and cleaner route Setting 3: 20°-20°, for round pools.
Note: These are the recommended settings. Different settings may work better for your pool.
4.
a.
Clean the filter tray
Open the cleaner by the clips
b. Take out the filter tray V. Trouble shooting VI.
VII.
This product has passed all quality control and safety tests, conducted by the technical department of the factory.
Warranty information:
1.
2.
3.
4.
5.
Packing list
Warranty
The warranty period is 12 months of use on the motors and electrical parts from the date of purchase and established under the terms
of the Consumer Code and the legal guarantee against hidden defects and vices in any case applies in the conditions of the articles in
the country of purchase.
The warranty is void if the product is handled or repaired by nonqualified person in unauthorized repair services.
Broken parts are not covered by the warranty.
The warranty only covers factory defects, it does not cover damage caused by misuse of the article.
Any claim made or repair made during the warranty period will be subject to mandatory presentation of the invoice.
- 02 -

Important Precautions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Do not power on the cleaner when it is out of the water.
Strictly prohibit using the cleaner beyond its operating conditions. Please read the manual carefully, and use it according to the manual.
We have no responsibility for any loss or injury caused by improper use.
Use the accessories recommended or sold by the manufacturer only.
This model mainly applies to swimming pools with a flat floor.
The cleaner should not be used by children under the age of 8 or people with mental disorders. Please do so under the supervision of
the guardian if necessary. Please do not allow children to ride on it or play as a toy.
Use the original and authorized power adapter only.
It must be replaced by the after-sale professionals if the power line is damaged.
The power line must be connected to a leakage protected and earthed socket when charging.
Do not operate the cleaner when there are people in the pool.
Always clean and wash the filter tray after use.
Power off the cleaner when maintaining, cleaning or not using it.
The cleaner should be stored in a cool and ventilated place, away from direct sunshine.
Charge the battery under the permitted condition. The cleaner should be stored in a cool place when charging, meanwhile do not
place or be covered with anything to prevent the damage of internal electrical components caused by overheating of the power unit.
Only professionals can disassemble the sealed driving kit of the cleaner.
Close the pool filtration system before use.
The cleaner should be charged every three months if it needs to be stored for a long time. Please use the original and authorized
adapter only to ensure that the battery power is maintained at 40%-60%. The battery voltage will be lower than the over-discharge
protection voltage due to the self-discharge of battery if not charging the battery for a long time, which will lead to fatal damage to the
battery if continuing too long. Please be careful.
Prohibit charging the battery under the condition of fire or extreme heat. Do not use or store the cleaner near the heat source.
Prohibit piercing the cleaner shell with nails or other sharp objects, and prohibit hammering, impacting and throwing the cleaner.
I.
The robotic pool cleaner Cyber is a new type of rechargeable automatic cleaning equipment for pools with the function of automatic
beaching.
The cleaning function is upgraded, and the half-way turn-back function is activated for 5-12 times every 20 times the wall is hit, so that
the center of the swimming pool is no longer a dead corner for cleaning.
Introduction III.Specifications IV.
1.
a.
b.
Operation instruction
Precautions
Install the brush before use to avoid possible dirt leaks.
Please ensure that the top cover of the cleaner is tightly assembled to its chassis.
c.
d.
e.
f.
g.
After turning on, the cleaner must be placed in the pool within 20 seconds
Put into or lift out of the pool with the cleaner bottom towards the wall to avoid any possible scratches to the pool.
Power off the cleaner after use.
Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting into or lifting out of the pool.
It is necessary to stay on the water surface for 10-15 seconds until water flows out from the cleaner to the pool before being placed on the ground.
g.
2.
a.
*
*
*
b.
*
Lift the handle or clips of the cleaner out from the pool.
Quick operation
Plug in the cleaner with the supplied adapter and charging line to charge the battery.
Turn the switch knob to OFF before charging.
Clean the charging port before charging.
Keep the machine charging port and the adapter dry when charging.
Turn the switch knob to power on or off the cleaner
Please put into water within 20 seconds after turning on.
c.
d.
e.
3.
There are two nozzles on the cleaner, one of them opens once the other closes. Water flows out through the open nozzle to thrust the
cleaner forward. Adjust the nozzle by turning it to control the cleaner route.
Turn the switch knob to ON, the cleaner is power-on and the indicator light is steady blue, then put it into water. About 15 seconds after
power-on, the cleaner begins to work, and the blue light flashes.
When battery power is low, the cleaner will move close to the pool wall. The red-light fast flashes. The cleaner stops running when it
runs out of battery.
Indicators
Functions and adjustment of nozzles
a.
The nozzles of the cleaner are marked with angles (0°-40°).
The cleaner moves in an approximately straight line when the nozzle angle is 0°.
The cleaner moves in a more curved line at a larger angle from 0°-40°.
Setting 1: default setting: 0°-20°, for most of pools.
Setting 2: 0°-40°, when setting 1 does not manage a full coverage of the pool.
Setting nozzle angle and cleaner route Setting 3: 20°-20°, for round pools.
Note: These are the recommended settings. Different settings may work better for your pool.
4.
a.
Clean the filter tray
Open the cleaner by the clips
b. Take out the filter tray V. Trouble shooting VI.
VII.
This product has passed all quality control and safety tests, conducted by the technical department of the factory.
Warranty information:
1.
2.
3.
4.
5.
Packing list
Warranty
The warranty period is 12 months of use on the motors and electrical parts from the date of purchase and established under the terms
of the Consumer Code and the legal guarantee against hidden defects and vices in any case applies in the conditions of the articles in
the country of purchase.
The warranty is void if the product is handled or repaired by nonqualified person in unauthorized repair services.
Broken parts are not covered by the warranty.
The warranty only covers factory defects, it does not cover damage caused by misuse of the article.
Any claim made or repair made during the warranty period will be subject to mandatory presentation of the invoice.
- 03 -
Ideal for Residential Flat Bottom Pools
Please note that it’s not an all-rounder
For all above / half above ground pools
For Inground Pools of Flat Bottom (Water Depth < 6.6ft)
Not for deep shallow ends, Can’t climb walls or stairs
WARM TIPS:Only suitable for flat-bottom pools, not
climbing walls or slopes more than 15 degrees.
15°

Important Precautions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Do not power on the cleaner when it is out of the water.
Strictly prohibit using the cleaner beyond its operating conditions. Please read the manual carefully, and use it according to the manual.
We have no responsibility for any loss or injury caused by improper use.
Use the accessories recommended or sold by the manufacturer only.
This model mainly applies to swimming pools with a flat floor.
The cleaner should not be used by children under the age of 8 or people with mental disorders. Please do so under the supervision of
the guardian if necessary. Please do not allow children to ride on it or play as a toy.
Use the original and authorized power adapter only.
It must be replaced by the after-sale professionals if the power line is damaged.
The power line must be connected to a leakage protected and earthed socket when charging.
Do not operate the cleaner when there are people in the pool.
Always clean and wash the filter tray after use.
Power off the cleaner when maintaining, cleaning or not using it.
The cleaner should be stored in a cool and ventilated place, away from direct sunshine.
Charge the battery under the permitted condition. The cleaner should be stored in a cool place when charging, meanwhile do not
place or be covered with anything to prevent the damage of internal electrical components caused by overheating of the power unit.
Only professionals can disassemble the sealed driving kit of the cleaner.
Close the pool filtration system before use.
The cleaner should be charged every three months if it needs to be stored for a long time. Please use the original and authorized
adapter only to ensure that the battery power is maintained at 40%-60%. The battery voltage will be lower than the over-discharge
protection voltage due to the self-discharge of battery if not charging the battery for a long time, which will lead to fatal damage to the
battery if continuing too long. Please be careful.
Prohibit charging the battery under the condition of fire or extreme heat. Do not use or store the cleaner near the heat source.
Prohibit piercing the cleaner shell with nails or other sharp objects, and prohibit hammering, impacting and throwing the cleaner.
I.
The robotic pool cleaner Cyber is a new type of rechargeable automatic cleaning equipment for pools with the function of automatic
beaching.
The cleaning function is upgraded, and the half-way turn-back function is activated for 5-12 times every 20 times the wall is hit, so that
the center of the swimming pool is no longer a dead corner for cleaning.
Introduction III.Specifications IV.
1.
a.
b.
Operation instruction
Precautions
Install the brush before use to avoid possible dirt leaks.
Please ensure that the top cover of the cleaner is tightly assembled to its chassis.
c.
d.
e.
f.
g.
After turning on, the cleaner must be placed in the pool within 20 seconds
Put into or lift out of the pool with the cleaner bottom towards the wall to avoid any possible scratches to the pool.
Power off the cleaner after use.
Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting into or lifting out of the pool.
It is necessary to stay on the water surface for 10-15 seconds until water flows out from the cleaner to the pool before being placed on the ground.
g.
2.
a.
*
*
*
b.
*
Lift the handle or clips of the cleaner out from the pool.
Quick operation
Plug in the cleaner with the supplied adapter and charging line to charge the battery.
Turn the switch knob to OFF before charging.
Clean the charging port before charging.
Keep the machine charging port and the adapter dry when charging.
Turn the switch knob to power on or off the cleaner
Please put into water within 20 seconds after turning on.
c.
d.
e.
3.
There are two nozzles on the cleaner, one of them opens once the other closes. Water flows out through the open nozzle to thrust the
cleaner forward. Adjust the nozzle by turning it to control the cleaner route.
Turn the switch knob to ON, the cleaner is power-on and the indicator light is steady blue, then put it into water. About 15 seconds after
power-on, the cleaner begins to work, and the blue light flashes.
When battery power is low, the cleaner will move close to the pool wall. The red-light fast flashes. The cleaner stops running when it
runs out of battery.
Indicators
Functions and adjustment of nozzles
a.
The nozzles of the cleaner are marked with angles (0°-40°).
The cleaner moves in an approximately straight line when the nozzle angle is 0°.
The cleaner moves in a more curved line at a larger angle from 0°-40°.
Setting 1: default setting: 0°-20°, for most of pools.
Setting 2: 0°-40°, when setting 1 does not manage a full coverage of the pool.
Setting nozzle angle and cleaner route Setting 3: 20°-20°, for round pools.
Note: These are the recommended settings. Different settings may work better for your pool.
4.
a.
Clean the filter tray
Open the cleaner by the clips
b. Take out the filter tray V. Trouble shooting VI.
VII.
This product has passed all quality control and safety tests, conducted by the technical department of the factory.
Warranty information:
1.
2.
3.
4.
5.
Packing list
Warranty
The warranty period is 12 months of use on the motors and electrical parts from the date of purchase and established under the terms
of the Consumer Code and the legal guarantee against hidden defects and vices in any case applies in the conditions of the articles in
the country of purchase.
The warranty is void if the product is handled or repaired by nonqualified person in unauthorized repair services.
Broken parts are not covered by the warranty.
The warranty only covers factory defects, it does not cover damage caused by misuse of the article.
Any claim made or repair made during the warranty period will be subject to mandatory presentation of the invoice.
- 04 -
Please read this manual carefully before use.

Important Precautions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Do not power on the cleaner when it is out of the water.
Strictly prohibit using the cleaner beyond its operating conditions. Please read the manual carefully, and use it according to the manual.
We have no responsibility for any loss or injury caused by improper use.
Use the accessories recommended or sold by the manufacturer only.
This model mainly applies to swimming pools with a flat floor.
The cleaner should not be used by children under the age of 8 or people with mental disorders. Please do so under the supervision of
the guardian if necessary. Please do not allow children to ride on it or play as a toy.
Use the original and authorized power adapter only.
It must be replaced by the after-sale professionals if the power line is damaged.
The power line must be connected to a leakage protected and earthed socket when charging.
Do not operate the cleaner when there are people in the pool.
Always clean and wash the filter tray after use.
Power off the cleaner when maintaining, cleaning or not using it.
The cleaner should be stored in a cool and ventilated place, away from direct sunshine.
Charge the battery under the permitted condition. The cleaner should be stored in a cool place when charging, meanwhile do not
place or be covered with anything to prevent the damage of internal electrical components caused by overheating of the power unit.
Only professionals can disassemble the sealed driving kit of the cleaner.
Close the pool filtration system before use.
The cleaner should be charged every three months if it needs to be stored for a long time. Please use the original and authorized
adapter only to ensure that the battery power is maintained at 40%-60%. The battery voltage will be lower than the over-discharge
protection voltage due to the self-discharge of battery if not charging the battery for a long time, which will lead to fatal damage to the
battery if continuing too long. Please be careful.
Prohibit charging the battery under the condition of fire or extreme heat. Do not use or store the cleaner near the heat source.
Prohibit piercing the cleaner shell with nails or other sharp objects, and prohibit hammering, impacting and throwing the cleaner.
I.
The robotic pool cleaner Cyber is a new type of rechargeable automatic cleaning equipment for pools with the function of automatic
beaching.
The cleaning function is upgraded, and the half-way turn-back function is activated for 5-12 times every 20 times the wall is hit, so that
the center of the swimming pool is no longer a dead corner for cleaning.
Introduction
Floating handle Brush
Chassis
Filter tray
Swing plate
III.Specifications IV.
1.
a.
b.
Operation instruction
Precautions
Install the brush before use to avoid possible dirt leaks.
Please ensure that the top cover of the cleaner is tightly assembled to its chassis.
c.
d.
e.
f.
g.
After turning on, the cleaner must be placed in the pool within 20 seconds
Put into or lift out of the pool with the cleaner bottom towards the wall to avoid any possible scratches to the pool.
Power off the cleaner after use.
Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting into or lifting out of the pool.
It is necessary to stay on the water surface for 10-15 seconds until water flows out from the cleaner to the pool before being placed on the ground.
g.
2.
a.
*
*
*
b.
*
Lift the handle or clips of the cleaner out from the pool.
Quick operation
Plug in the cleaner with the supplied adapter and charging line to charge the battery.
Turn the switch knob to OFF before charging.
Clean the charging port before charging.
Keep the machine charging port and the adapter dry when charging.
Turn the switch knob to power on or off the cleaner
Please put into water within 20 seconds after turning on.
c.
d.
e.
3.
There are two nozzles on the cleaner, one of them opens once the other closes. Water flows out through the open nozzle to thrust the
cleaner forward. Adjust the nozzle by turning it to control the cleaner route.
Turn the switch knob to ON, the cleaner is power-on and the indicator light is steady blue, then put it into water. About 15 seconds after
power-on, the cleaner begins to work, and the blue light flashes.
When battery power is low, the cleaner will move close to the pool wall. The red-light fast flashes. The cleaner stops running when it
runs out of battery.
Indicators
Functions and adjustment of nozzles
a.
The nozzles of the cleaner are marked with angles (0°-40°).
The cleaner moves in an approximately straight line when the nozzle angle is 0°.
The cleaner moves in a more curved line at a larger angle from 0°-40°.
Setting 1: default setting: 0°-20°, for most of pools.
Setting 2: 0°-40°, when setting 1 does not manage a full coverage of the pool.
Setting nozzle angle and cleaner route Setting 3: 20°-20°, for round pools.
Note: These are the recommended settings. Different settings may work better for your pool.
4.
a.
Clean the filter tray
Open the cleaner by the clips
b. Take out the filter tray V. Trouble shooting VI.
VII.
This product has passed all quality control and safety tests, conducted by the technical department of the factory.
Warranty information:
1.
2.
3.
4.
5.
Packing list
Warranty
The warranty period is 12 months of use on the motors and electrical parts from the date of purchase and established under the terms
of the Consumer Code and the legal guarantee against hidden defects and vices in any case applies in the conditions of the articles in
the country of purchase.
The warranty is void if the product is handled or repaired by nonqualified person in unauthorized repair services.
Broken parts are not covered by the warranty.
The warranty only covers factory defects, it does not cover damage caused by misuse of the article.
Any claim made or repair made during the warranty period will be subject to mandatory presentation of the invoice.
- 05 -
II. Appearance&structure

Important Precautions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Do not power on the cleaner when it is out of the water.
Strictly prohibit using the cleaner beyond its operating conditions. Please read the manual carefully, and use it according to the manual.
We have no responsibility for any loss or injury caused by improper use.
Use the accessories recommended or sold by the manufacturer only.
This model mainly applies to swimming pools with a flat floor.
The cleaner should not be used by children under the age of 8 or people with mental disorders. Please do so under the supervision of
the guardian if necessary. Please do not allow children to ride on it or play as a toy.
Use the original and authorized power adapter only.
It must be replaced by the after-sale professionals if the power line is damaged.
The power line must be connected to a leakage protected and earthed socket when charging.
Do not operate the cleaner when there are people in the pool.
Always clean and wash the filter tray after use.
Power off the cleaner when maintaining, cleaning or not using it.
The cleaner should be stored in a cool and ventilated place, away from direct sunshine.
Charge the battery under the permitted condition. The cleaner should be stored in a cool place when charging, meanwhile do not
place or be covered with anything to prevent the damage of internal electrical components caused by overheating of the power unit.
Only professionals can disassemble the sealed driving kit of the cleaner.
Close the pool filtration system before use.
The cleaner should be charged every three months if it needs to be stored for a long time. Please use the original and authorized
adapter only to ensure that the battery power is maintained at 40%-60%. The battery voltage will be lower than the over-discharge
protection voltage due to the self-discharge of battery if not charging the battery for a long time, which will lead to fatal damage to the
battery if continuing too long. Please be careful.
Prohibit charging the battery under the condition of fire or extreme heat. Do not use or store the cleaner near the heat source.
Prohibit piercing the cleaner shell with nails or other sharp objects, and prohibit hammering, impacting and throwing the cleaner.
I.
The robotic pool cleaner Cyber is a new type of rechargeable automatic cleaning equipment for pools with the function of automatic
beaching.
The cleaning function is upgraded, and the half-way turn-back function is activated for 5-12 times every 20 times the wall is hit, so that
the center of the swimming pool is no longer a dead corner for cleaning.
Introduction III.Specifications
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
Name:
Model:
Rated input voltage/frequency of charger:
Rated output voltage of charger:
Rated output current of charger:
Working power
Working time:
Battery capacity:
Charging time:
Max. cleaning surface:
Filter capacity:
Filter capability:
Swimming pool slope:
Pool water temperature:
Moving speed:
IP Grade:
Charging environment temperature:
Max. water depth:
Storage condition:
Short term (less than 1 month):
Medium term (less than 3 months):
Long term (more than 3 months):
Cordless Robotic Pool Cleaner
Cyber
100Vac-240Vac, 50/60Hz
12.6V
1.8A
Appr. 50W
max. 120min for one cycle
6600mAh
5-6h
Appr. 1076ft² or 100m²
Appr. 2641us gal or 10m³/h
180μm
max. 15°
(50°F) - (95°F) /10℃-35℃
Appr. 52.4ft or 16m/min
IPX8 (main body)
(32°F) - (113°F) /0℃-45℃
6.56ft or 2.0m
Short term (less than 1 month): (-4°F) - (+140°F) / (-20℃)-(+60℃) ≤ 75%RH
Medium term (less than 3 months): (-4°F) - (+113°F) / (-20℃)-(+45℃) ≤ 75%RH
Long term (more than 3 months): (-4°F) - (+68°F) / (-20℃)-(+20℃) ≤ 75%RH
IV.
1.
a.
b.
Operation instruction
Precautions
Install the brush before use to avoid possible dirt leaks.
Please ensure that the top cover of the cleaner is tightly assembled to its chassis.
c.
d.
e.
f.
g.
After turning on, the cleaner must be placed in the pool within 20 seconds
Put into or lift out of the pool with the cleaner bottom towards the wall to avoid any possible scratches to the pool.
Power off the cleaner after use.
Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting into or lifting out of the pool.
It is necessary to stay on the water surface for 10-15 seconds until water flows out from the cleaner to the pool before being placed on the ground.
g.
2.
a.
*
*
*
b.
*
Lift the handle or clips of the cleaner out from the pool.
Quick operation
Plug in the cleaner with the supplied adapter and charging line to charge the battery.
Turn the switch knob to OFF before charging.
Clean the charging port before charging.
Keep the machine charging port and the adapter dry when charging.
Turn the switch knob to power on or off the cleaner
Please put into water within 20 seconds after turning on.
c.
d.
e.
3.
There are two nozzles on the cleaner, one of them opens once the other closes. Water flows out through the open nozzle to thrust the
cleaner forward. Adjust the nozzle by turning it to control the cleaner route.
Turn the switch knob to ON, the cleaner is power-on and the indicator light is steady blue, then put it into water. About 15 seconds after
power-on, the cleaner begins to work, and the blue light flashes.
When battery power is low, the cleaner will move close to the pool wall. The red-light fast flashes. The cleaner stops running when it
runs out of battery.
Indicators
Functions and adjustment of nozzles
a.
The nozzles of the cleaner are marked with angles (0°-40°).
The cleaner moves in an approximately straight line when the nozzle angle is 0°.
The cleaner moves in a more curved line at a larger angle from 0°-40°.
Setting 1: default setting: 0°-20°, for most of pools.
Setting 2: 0°-40°, when setting 1 does not manage a full coverage of the pool.
Setting nozzle angle and cleaner route Setting 3: 20°-20°, for round pools.
Note: These are the recommended settings. Different settings may work better for your pool.
4.
a.
Clean the filter tray
Open the cleaner by the clips
b. Take out the filter tray V. Trouble shooting VI.
VII.
This product has passed all quality control and safety tests, conducted by the technical department of the factory.
Warranty information:
1.
2.
3.
4.
5.
Packing list
Warranty
The warranty period is 12 months of use on the motors and electrical parts from the date of purchase and established under the terms
of the Consumer Code and the legal guarantee against hidden defects and vices in any case applies in the conditions of the articles in
the country of purchase.
The warranty is void if the product is handled or repaired by nonqualified person in unauthorized repair services.
Broken parts are not covered by the warranty.
The warranty only covers factory defects, it does not cover damage caused by misuse of the article.
Any claim made or repair made during the warranty period will be subject to mandatory presentation of the invoice.
- 06 -

Important Precautions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Do not power on the cleaner when it is out of the water.
Strictly prohibit using the cleaner beyond its operating conditions. Please read the manual carefully, and use it according to the manual.
We have no responsibility for any loss or injury caused by improper use.
Use the accessories recommended or sold by the manufacturer only.
This model mainly applies to swimming pools with a flat floor.
The cleaner should not be used by children under the age of 8 or people with mental disorders. Please do so under the supervision of
the guardian if necessary. Please do not allow children to ride on it or play as a toy.
Use the original and authorized power adapter only.
It must be replaced by the after-sale professionals if the power line is damaged.
The power line must be connected to a leakage protected and earthed socket when charging.
Do not operate the cleaner when there are people in the pool.
Always clean and wash the filter tray after use.
Power off the cleaner when maintaining, cleaning or not using it.
The cleaner should be stored in a cool and ventilated place, away from direct sunshine.
Charge the battery under the permitted condition. The cleaner should be stored in a cool place when charging, meanwhile do not
place or be covered with anything to prevent the damage of internal electrical components caused by overheating of the power unit.
Only professionals can disassemble the sealed driving kit of the cleaner.
Close the pool filtration system before use.
The cleaner should be charged every three months if it needs to be stored for a long time. Please use the original and authorized
adapter only to ensure that the battery power is maintained at 40%-60%. The battery voltage will be lower than the over-discharge
protection voltage due to the self-discharge of battery if not charging the battery for a long time, which will lead to fatal damage to the
battery if continuing too long. Please be careful.
Prohibit charging the battery under the condition of fire or extreme heat. Do not use or store the cleaner near the heat source.
Prohibit piercing the cleaner shell with nails or other sharp objects, and prohibit hammering, impacting and throwing the cleaner.
I.
The robotic pool cleaner Cyber is a new type of rechargeable automatic cleaning equipment for pools with the function of automatic
beaching.
The cleaning function is upgraded, and the half-way turn-back function is activated for 5-12 times every 20 times the wall is hit, so that
the center of the swimming pool is no longer a dead corner for cleaning.
Introduction III.Specifications IV.
1.
a.
b.
Operation instruction
Precautions
Install the brush before use to avoid possible dirt leaks.
Please ensure that the top cover of the cleaner is tightly assembled to its chassis.
c.
d.
e.
f.
g.
After turning on, the cleaner must be placed in the pool within 20 seconds
Put into or lift out of the pool with the cleaner bottom towards the wall to avoid any possible scratches to the pool.
Power off the cleaner after use.
Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting into or lifting out of the pool.
It is necessary to stay on the water surface for 10-15 seconds until water flows out from the cleaner to the pool before being placed on the ground.
g.
2.
a.
*
*
*
b.
*
Lift the handle or clips of the cleaner out from the pool.
Quick operation
Plug in the cleaner with the supplied adapter and charging line to charge the battery.
Turn the switch knob to OFF before charging.
Clean the charging port before charging.
Keep the machine charging port and the adapter dry when charging.
Turn the switch knob to power on or off the cleaner
Please put into water within 20 seconds after turning on.
c.
d.
e.
3.
There are two nozzles on the cleaner, one of them opens once the other closes. Water flows out through the open nozzle to thrust the
cleaner forward. Adjust the nozzle by turning it to control the cleaner route.
Turn the switch knob to ON, the cleaner is power-on and the indicator light is steady blue, then put it into water. About 15 seconds after
power-on, the cleaner begins to work, and the blue light flashes.
When battery power is low, the cleaner will move close to the pool wall. The red-light fast flashes. The cleaner stops running when it
runs out of battery.
Indicators
Functions and adjustment of nozzles
a.
The nozzles of the cleaner are marked with angles (0°-40°).
The cleaner moves in an approximately straight line when the nozzle angle is 0°.
The cleaner moves in a more curved line at a larger angle from 0°-40°.
Setting 1: default setting: 0°-20°, for most of pools.
Setting 2: 0°-40°, when setting 1 does not manage a full coverage of the pool.
Setting nozzle angle and cleaner route Setting 3: 20°-20°, for round pools.
Note: These are the recommended settings. Different settings may work better for your pool.
4.
a.
Clean the filter tray
Open the cleaner by the clips
b. Take out the filter tray V. Trouble shooting VI.
VII.
This product has passed all quality control and safety tests, conducted by the technical department of the factory.
Warranty information:
1.
2.
3.
4.
5.
Packing list
Warranty
The warranty period is 12 months of use on the motors and electrical parts from the date of purchase and established under the terms
of the Consumer Code and the legal guarantee against hidden defects and vices in any case applies in the conditions of the articles in
the country of purchase.
The warranty is void if the product is handled or repaired by nonqualified person in unauthorized repair services.
Broken parts are not covered by the warranty.
The warranty only covers factory defects, it does not cover damage caused by misuse of the article.
Any claim made or repair made during the warranty period will be subject to mandatory presentation of the invoice.
- 07 -

Important Precautions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Do not power on the cleaner when it is out of the water.
Strictly prohibit using the cleaner beyond its operating conditions. Please read the manual carefully, and use it according to the manual.
We have no responsibility for any loss or injury caused by improper use.
Use the accessories recommended or sold by the manufacturer only.
This model mainly applies to swimming pools with a flat floor.
The cleaner should not be used by children under the age of 8 or people with mental disorders. Please do so under the supervision of
the guardian if necessary. Please do not allow children to ride on it or play as a toy.
Use the original and authorized power adapter only.
It must be replaced by the after-sale professionals if the power line is damaged.
The power line must be connected to a leakage protected and earthed socket when charging.
Do not operate the cleaner when there are people in the pool.
Always clean and wash the filter tray after use.
Power off the cleaner when maintaining, cleaning or not using it.
The cleaner should be stored in a cool and ventilated place, away from direct sunshine.
Charge the battery under the permitted condition. The cleaner should be stored in a cool place when charging, meanwhile do not
place or be covered with anything to prevent the damage of internal electrical components caused by overheating of the power unit.
Only professionals can disassemble the sealed driving kit of the cleaner.
Close the pool filtration system before use.
The cleaner should be charged every three months if it needs to be stored for a long time. Please use the original and authorized
adapter only to ensure that the battery power is maintained at 40%-60%. The battery voltage will be lower than the over-discharge
protection voltage due to the self-discharge of battery if not charging the battery for a long time, which will lead to fatal damage to the
battery if continuing too long. Please be careful.
Prohibit charging the battery under the condition of fire or extreme heat. Do not use or store the cleaner near the heat source.
Prohibit piercing the cleaner shell with nails or other sharp objects, and prohibit hammering, impacting and throwing the cleaner.
I.
The robotic pool cleaner Cyber is a new type of rechargeable automatic cleaning equipment for pools with the function of automatic
beaching.
The cleaning function is upgraded, and the half-way turn-back function is activated for 5-12 times every 20 times the wall is hit, so that
the center of the swimming pool is no longer a dead corner for cleaning.
Introduction III.Specifications IV.
1.
a.
b.
Operation instruction
Precautions
Install the brush before use to avoid possible dirt leaks.
Please ensure that the top cover of the cleaner is tightly assembled to its chassis.
c.
d.
e.
f.
g.
After turning on, the cleaner must be placed in the pool within 20 seconds
Put into or lift out of the pool with the cleaner bottom towards the wall to avoid any possible scratches to the pool.
Power off the cleaner after use.
Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting into or lifting out of the pool.
It is necessary to stay on the water surface for 10-15 seconds until water flows out from the cleaner to the pool before being placed on the ground.
g.
2.
a.
*
*
*
b.
*
Lift the handle or clips of the cleaner out from the pool.
Quick operation
Plug in the cleaner with the supplied adapter and charging line to charge the battery.
Turn the switch knob to OFF before charging.
Clean the charging port before charging.
Keep the machine charging port and the adapter dry when charging.
Turn the switch knob to power on or off the cleaner
Please put into water within 20 seconds after turning on.
c.
d.
e.
3.
There are two nozzles on the cleaner, one of them opens once the other closes. Water flows out through the open nozzle to thrust the
cleaner forward. Adjust the nozzle by turning it to control the cleaner route.
Turn the switch knob to ON, the cleaner is power-on and the indicator light is steady blue, then put it into water. About 15 seconds after
power-on, the cleaner begins to work, and the blue light flashes.
When battery power is low, the cleaner will move close to the pool wall. The red-light fast flashes. The cleaner stops running when it
runs out of battery.
Indicators
Functions and adjustment of nozzles
a.
The nozzles of the cleaner are marked with angles (0°-40°).
The cleaner moves in an approximately straight line when the nozzle angle is 0°.
The cleaner moves in a more curved line at a larger angle from 0°-40°.
Setting 1: default setting: 0°-20°, for most of pools.
Setting 2: 0°-40°, when setting 1 does not manage a full coverage of the pool.
Setting nozzle angle and cleaner route Setting 3: 20°-20°, for round pools.
Note: These are the recommended settings. Different settings may work better for your pool.
4.
a.
Clean the filter tray
Open the cleaner by the clips
b. Take out the filter tray V. Trouble shooting VI.
VII.
This product has passed all quality control and safety tests, conducted by the technical department of the factory.
Warranty information:
1.
2.
3.
4.
5.
Packing list
Warranty
The warranty period is 12 months of use on the motors and electrical parts from the date of purchase and established under the terms
of the Consumer Code and the legal guarantee against hidden defects and vices in any case applies in the conditions of the articles in
the country of purchase.
The warranty is void if the product is handled or repaired by nonqualified person in unauthorized repair services.
Broken parts are not covered by the warranty.
The warranty only covers factory defects, it does not cover damage caused by misuse of the article.
Any claim made or repair made during the warranty period will be subject to mandatory presentation of the invoice.
- 08 -

Important Precautions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Do not power on the cleaner when it is out of the water.
Strictly prohibit using the cleaner beyond its operating conditions. Please read the manual carefully, and use it according to the manual.
We have no responsibility for any loss or injury caused by improper use.
Use the accessories recommended or sold by the manufacturer only.
This model mainly applies to swimming pools with a flat floor.
The cleaner should not be used by children under the age of 8 or people with mental disorders. Please do so under the supervision of
the guardian if necessary. Please do not allow children to ride on it or play as a toy.
Use the original and authorized power adapter only.
It must be replaced by the after-sale professionals if the power line is damaged.
The power line must be connected to a leakage protected and earthed socket when charging.
Do not operate the cleaner when there are people in the pool.
Always clean and wash the filter tray after use.
Power off the cleaner when maintaining, cleaning or not using it.
The cleaner should be stored in a cool and ventilated place, away from direct sunshine.
Charge the battery under the permitted condition. The cleaner should be stored in a cool place when charging, meanwhile do not
place or be covered with anything to prevent the damage of internal electrical components caused by overheating of the power unit.
Only professionals can disassemble the sealed driving kit of the cleaner.
Close the pool filtration system before use.
The cleaner should be charged every three months if it needs to be stored for a long time. Please use the original and authorized
adapter only to ensure that the battery power is maintained at 40%-60%. The battery voltage will be lower than the over-discharge
protection voltage due to the self-discharge of battery if not charging the battery for a long time, which will lead to fatal damage to the
battery if continuing too long. Please be careful.
Prohibit charging the battery under the condition of fire or extreme heat. Do not use or store the cleaner near the heat source.
Prohibit piercing the cleaner shell with nails or other sharp objects, and prohibit hammering, impacting and throwing the cleaner.
I.
The robotic pool cleaner Cyber is a new type of rechargeable automatic cleaning equipment for pools with the function of automatic
beaching.
The cleaning function is upgraded, and the half-way turn-back function is activated for 5-12 times every 20 times the wall is hit, so that
the center of the swimming pool is no longer a dead corner for cleaning.
Introduction III.Specifications IV.
1.
a.
b.
Operation instruction
Precautions
Install the brush before use to avoid possible dirt leaks.
Please ensure that the top cover of the cleaner is tightly assembled to its chassis.
c.
d.
e.
f.
g.
After turning on, the cleaner must be placed in the pool within 20 seconds
Put into or lift out of the pool with the cleaner bottom towards the wall to avoid any possible scratches to the pool.
Power off the cleaner after use.
Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting into or lifting out of the pool.
It is necessary to stay on the water surface for 10-15 seconds until water flows out from the cleaner to the pool before being placed on the ground.
Adapter indicator
Red
Green
Status
Battery is charging
Charging is finished
g.
2.
a.
*
*
*
b.
*
Lift the handle or clips of the cleaner out from the pool.
Quick operation
Plug in the cleaner with the supplied adapter and charging line to charge the battery.
Turn the switch knob to OFF before charging.
Clean the charging port before charging.
Keep the machine charging port and the adapter dry when charging.
Turn the switch knob to power on or off the cleaner
Please put into water within 20 seconds after turning on.
ON OFF
c.
d.
e.
3.
There are two nozzles on the cleaner, one of them opens once the other closes. Water flows out through the open nozzle to thrust the
cleaner forward. Adjust the nozzle by turning it to control the cleaner route.
Turn the switch knob to ON, the cleaner is power-on and the indicator light is steady blue, then put it into water. About 15 seconds after
power-on, the cleaner begins to work, and the blue light flashes.
When battery power is low, the cleaner will move close to the pool wall. The red-light fast flashes. The cleaner stops running when it
runs out of battery.
Indicators
Functions and adjustment of nozzles
a.
The nozzles of the cleaner are marked with angles (0°-40°).
The cleaner moves in an approximately straight line when the nozzle angle is 0°.
The cleaner moves in a more curved line at a larger angle from 0°-40°.
Setting 1: default setting: 0°-20°, for most of pools.
Setting 2: 0°-40°, when setting 1 does not manage a full coverage of the pool.
Setting nozzle angle and cleaner route Setting 3: 20°-20°, for round pools.
Note: These are the recommended settings. Different settings may work better for your pool.
4.
a.
Clean the filter tray
Open the cleaner by the clips
b. Take out the filter tray V. Trouble shooting VI.
VII.
This product has passed all quality control and safety tests, conducted by the technical department of the factory.
Warranty information:
1.
2.
3.
4.
5.
Packing list
Warranty
The warranty period is 12 months of use on the motors and electrical parts from the date of purchase and established under the terms
of the Consumer Code and the legal guarantee against hidden defects and vices in any case applies in the conditions of the articles in
the country of purchase.
The warranty is void if the product is handled or repaired by nonqualified person in unauthorized repair services.
Broken parts are not covered by the warranty.
The warranty only covers factory defects, it does not cover damage caused by misuse of the article.
Any claim made or repair made during the warranty period will be subject to mandatory presentation of the invoice.
- 09 -

Important Precautions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Do not power on the cleaner when it is out of the water.
Strictly prohibit using the cleaner beyond its operating conditions. Please read the manual carefully, and use it according to the manual.
We have no responsibility for any loss or injury caused by improper use.
Use the accessories recommended or sold by the manufacturer only.
This model mainly applies to swimming pools with a flat floor.
The cleaner should not be used by children under the age of 8 or people with mental disorders. Please do so under the supervision of
the guardian if necessary. Please do not allow children to ride on it or play as a toy.
Use the original and authorized power adapter only.
It must be replaced by the after-sale professionals if the power line is damaged.
The power line must be connected to a leakage protected and earthed socket when charging.
Do not operate the cleaner when there are people in the pool.
Always clean and wash the filter tray after use.
Power off the cleaner when maintaining, cleaning or not using it.
The cleaner should be stored in a cool and ventilated place, away from direct sunshine.
Charge the battery under the permitted condition. The cleaner should be stored in a cool place when charging, meanwhile do not
place or be covered with anything to prevent the damage of internal electrical components caused by overheating of the power unit.
Only professionals can disassemble the sealed driving kit of the cleaner.
Close the pool filtration system before use.
The cleaner should be charged every three months if it needs to be stored for a long time. Please use the original and authorized
adapter only to ensure that the battery power is maintained at 40%-60%. The battery voltage will be lower than the over-discharge
protection voltage due to the self-discharge of battery if not charging the battery for a long time, which will lead to fatal damage to the
battery if continuing too long. Please be careful.
Prohibit charging the battery under the condition of fire or extreme heat. Do not use or store the cleaner near the heat source.
Prohibit piercing the cleaner shell with nails or other sharp objects, and prohibit hammering, impacting and throwing the cleaner.
I.
The robotic pool cleaner Cyber is a new type of rechargeable automatic cleaning equipment for pools with the function of automatic
beaching.
The cleaning function is upgraded, and the half-way turn-back function is activated for 5-12 times every 20 times the wall is hit, so that
the center of the swimming pool is no longer a dead corner for cleaning.
Introduction III.Specifications IV.
1.
a.
b.
Operation instruction
Precautions
Install the brush before use to avoid possible dirt leaks.
Please ensure that the top cover of the cleaner is tightly assembled to its chassis.
c.
d.
e.
f.
g.
After turning on, the cleaner must be placed in the pool within 20 seconds
Put into or lift out of the pool with the cleaner bottom towards the wall to avoid any possible scratches to the pool.
Power off the cleaner after use.
Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting into or lifting out of the pool.
It is necessary to stay on the water surface for 10-15 seconds until water flows out from the cleaner to the pool before being placed on the ground.
g.
2.
a.
*
*
*
b.
*
Lift the handle or clips of the cleaner out from the pool.
Quick operation
Plug in the cleaner with the supplied adapter and charging line to charge the battery.
Turn the switch knob to OFF before charging.
Clean the charging port before charging.
Keep the machine charging port and the adapter dry when charging.
Turn the switch knob to power on or off the cleaner
Please put into water within 20 seconds after turning on.
c.
d.
e.
3.
There are two nozzles on the cleaner, one of them opens once the other closes. Water flows out through the open nozzle to thrust the
cleaner forward. Adjust the nozzle by turning it to control the cleaner route.
Status
Solid blue
Blue light fast flashing
Blue light slow flashing
Flashing Red
Meaning
Switch on
Cleaner is out of water
Cleaner is working in the pool
low battery
Turn the switch knob to ON, the cleaner is power-on and the indicator light is steady blue, then put it into water. About 15 seconds after
power-on, the cleaner begins to work, and the blue light flashes.
When battery power is low, the cleaner will move close to the pool wall. The red-light fast flashes. The cleaner stops running when it
runs out of battery.
Indicators
Functions and adjustment of nozzles
a.
The nozzles of the cleaner are marked with angles (0°-40°).
The cleaner moves in an approximately straight line when the nozzle angle is 0°.
The cleaner moves in a more curved line at a larger angle from 0°-40°.
Setting 1: default setting: 0°-20°, for most of pools.
Setting 2: 0°-40°, when setting 1 does not manage a full coverage of the pool.
Setting nozzle angle and cleaner route Setting 3: 20°-20°, for round pools.
Note: These are the recommended settings. Different settings may work better for your pool.
4.
a.
Clean the filter tray
Open the cleaner by the clips
b. Take out the filter tray V. Trouble shooting VI.
VII.
This product has passed all quality control and safety tests, conducted by the technical department of the factory.
Warranty information:
1.
2.
3.
4.
5.
Packing list
Warranty
The warranty period is 12 months of use on the motors and electrical parts from the date of purchase and established under the terms
of the Consumer Code and the legal guarantee against hidden defects and vices in any case applies in the conditions of the articles in
the country of purchase.
The warranty is void if the product is handled or repaired by nonqualified person in unauthorized repair services.
Broken parts are not covered by the warranty.
The warranty only covers factory defects, it does not cover damage caused by misuse of the article.
Any claim made or repair made during the warranty period will be subject to mandatory presentation of the invoice.
- 10 -

Important Precautions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Do not power on the cleaner when it is out of the water.
Strictly prohibit using the cleaner beyond its operating conditions. Please read the manual carefully, and use it according to the manual.
We have no responsibility for any loss or injury caused by improper use.
Use the accessories recommended or sold by the manufacturer only.
This model mainly applies to swimming pools with a flat floor.
The cleaner should not be used by children under the age of 8 or people with mental disorders. Please do so under the supervision of
the guardian if necessary. Please do not allow children to ride on it or play as a toy.
Use the original and authorized power adapter only.
It must be replaced by the after-sale professionals if the power line is damaged.
The power line must be connected to a leakage protected and earthed socket when charging.
Do not operate the cleaner when there are people in the pool.
Always clean and wash the filter tray after use.
Power off the cleaner when maintaining, cleaning or not using it.
The cleaner should be stored in a cool and ventilated place, away from direct sunshine.
Charge the battery under the permitted condition. The cleaner should be stored in a cool place when charging, meanwhile do not
place or be covered with anything to prevent the damage of internal electrical components caused by overheating of the power unit.
Only professionals can disassemble the sealed driving kit of the cleaner.
Close the pool filtration system before use.
The cleaner should be charged every three months if it needs to be stored for a long time. Please use the original and authorized
adapter only to ensure that the battery power is maintained at 40%-60%. The battery voltage will be lower than the over-discharge
protection voltage due to the self-discharge of battery if not charging the battery for a long time, which will lead to fatal damage to the
battery if continuing too long. Please be careful.
Prohibit charging the battery under the condition of fire or extreme heat. Do not use or store the cleaner near the heat source.
Prohibit piercing the cleaner shell with nails or other sharp objects, and prohibit hammering, impacting and throwing the cleaner.
I.
The robotic pool cleaner Cyber is a new type of rechargeable automatic cleaning equipment for pools with the function of automatic
beaching.
The cleaning function is upgraded, and the half-way turn-back function is activated for 5-12 times every 20 times the wall is hit, so that
the center of the swimming pool is no longer a dead corner for cleaning.
Introduction III.Specifications IV.
1.
a.
b.
Operation instruction
Precautions
Install the brush before use to avoid possible dirt leaks.
Please ensure that the top cover of the cleaner is tightly assembled to its chassis.
c.
d.
e.
f.
g.
After turning on, the cleaner must be placed in the pool within 20 seconds
Put into or lift out of the pool with the cleaner bottom towards the wall to avoid any possible scratches to the pool.
Power off the cleaner after use.
Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting into or lifting out of the pool.
It is necessary to stay on the water surface for 10-15 seconds until water flows out from the cleaner to the pool before being placed on the ground.
g.
2.
a.
*
*
*
b.
*
Lift the handle or clips of the cleaner out from the pool.
Quick operation
Plug in the cleaner with the supplied adapter and charging line to charge the battery.
Turn the switch knob to OFF before charging.
Clean the charging port before charging.
Keep the machine charging port and the adapter dry when charging.
Turn the switch knob to power on or off the cleaner
Please put into water within 20 seconds after turning on.
c.
d.
e.
3.
There are two nozzles on the cleaner, one of them opens once the other closes. Water flows out through the open nozzle to thrust the
cleaner forward. Adjust the nozzle by turning it to control the cleaner route.
Turn the switch knob to ON, the cleaner is power-on and the indicator light is steady blue, then put it into water. About 15 seconds after
power-on, the cleaner begins to work, and the blue light flashes.
When battery power is low, the cleaner will move close to the pool wall. The red-light fast flashes. The cleaner stops running when it
runs out of battery.
Indicators
Functions and adjustment of nozzles
a.
The nozzles of the cleaner are marked with angles (0°-40°).
The cleaner moves in an approximately straight line when the nozzle angle is 0°.
The cleaner moves in a more curved line at a larger angle from 0°-40°.
Setting 1: default setting: 0°-20°, for most of pools.
Setting 2: 0°-40°, when setting 1 does not manage a full coverage of the pool.
Setting nozzle angle and cleaner route
Running path
Running route
Setting 3: 20°-20°, for round pools.
Note: These are the recommended settings. Different settings may work better for your pool.
4.
a.
Clean the filter tray
Open the cleaner by the clips
b. Take out the filter tray V. Trouble shooting VI.
VII.
This product has passed all quality control and safety tests, conducted by the technical department of the factory.
Warranty information:
1.
2.
3.
4.
5.
Packing list
Warranty
The warranty period is 12 months of use on the motors and electrical parts from the date of purchase and established under the terms
of the Consumer Code and the legal guarantee against hidden defects and vices in any case applies in the conditions of the articles in
the country of purchase.
The warranty is void if the product is handled or repaired by nonqualified person in unauthorized repair services.
Broken parts are not covered by the warranty.
The warranty only covers factory defects, it does not cover damage caused by misuse of the article.
Any claim made or repair made during the warranty period will be subject to mandatory presentation of the invoice.
- 11 -
Nozzle angle
Nozzle angle

Important Precautions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Do not power on the cleaner when it is out of the water.
Strictly prohibit using the cleaner beyond its operating conditions. Please read the manual carefully, and use it according to the manual.
We have no responsibility for any loss or injury caused by improper use.
Use the accessories recommended or sold by the manufacturer only.
This model mainly applies to swimming pools with a flat floor.
The cleaner should not be used by children under the age of 8 or people with mental disorders. Please do so under the supervision of
the guardian if necessary. Please do not allow children to ride on it or play as a toy.
Use the original and authorized power adapter only.
It must be replaced by the after-sale professionals if the power line is damaged.
The power line must be connected to a leakage protected and earthed socket when charging.
Do not operate the cleaner when there are people in the pool.
Always clean and wash the filter tray after use.
Power off the cleaner when maintaining, cleaning or not using it.
The cleaner should be stored in a cool and ventilated place, away from direct sunshine.
Charge the battery under the permitted condition. The cleaner should be stored in a cool place when charging, meanwhile do not
place or be covered with anything to prevent the damage of internal electrical components caused by overheating of the power unit.
Only professionals can disassemble the sealed driving kit of the cleaner.
Close the pool filtration system before use.
The cleaner should be charged every three months if it needs to be stored for a long time. Please use the original and authorized
adapter only to ensure that the battery power is maintained at 40%-60%. The battery voltage will be lower than the over-discharge
protection voltage due to the self-discharge of battery if not charging the battery for a long time, which will lead to fatal damage to the
battery if continuing too long. Please be careful.
Prohibit charging the battery under the condition of fire or extreme heat. Do not use or store the cleaner near the heat source.
Prohibit piercing the cleaner shell with nails or other sharp objects, and prohibit hammering, impacting and throwing the cleaner.
I.
The robotic pool cleaner Cyber is a new type of rechargeable automatic cleaning equipment for pools with the function of automatic
beaching.
The cleaning function is upgraded, and the half-way turn-back function is activated for 5-12 times every 20 times the wall is hit, so that
the center of the swimming pool is no longer a dead corner for cleaning.
Introduction III.Specifications IV.
1.
a.
b.
Operation instruction
Precautions
Install the brush before use to avoid possible dirt leaks.
Please ensure that the top cover of the cleaner is tightly assembled to its chassis.
c.
d.
e.
f.
g.
After turning on, the cleaner must be placed in the pool within 20 seconds
Put into or lift out of the pool with the cleaner bottom towards the wall to avoid any possible scratches to the pool.
Power off the cleaner after use.
Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting into or lifting out of the pool.
It is necessary to stay on the water surface for 10-15 seconds until water flows out from the cleaner to the pool before being placed on the ground.
g.
2.
a.
*
*
*
b.
*
Lift the handle or clips of the cleaner out from the pool.
Quick operation
Plug in the cleaner with the supplied adapter and charging line to charge the battery.
Turn the switch knob to OFF before charging.
Clean the charging port before charging.
Keep the machine charging port and the adapter dry when charging.
Turn the switch knob to power on or off the cleaner
Please put into water within 20 seconds after turning on.
c.
d.
e.
3.
There are two nozzles on the cleaner, one of them opens once the other closes. Water flows out through the open nozzle to thrust the
cleaner forward. Adjust the nozzle by turning it to control the cleaner route.
Turn the switch knob to ON, the cleaner is power-on and the indicator light is steady blue, then put it into water. About 15 seconds after
power-on, the cleaner begins to work, and the blue light flashes.
When battery power is low, the cleaner will move close to the pool wall. The red-light fast flashes. The cleaner stops running when it
runs out of battery.
Indicators
Functions and adjustment of nozzles
a.
The nozzles of the cleaner are marked with angles (0°-40°).
The cleaner moves in an approximately straight line when the nozzle angle is 0°.
The cleaner moves in a more curved line at a larger angle from 0°-40°.
Setting 1: default setting: 0°-20°, for most of pools.
Setting 2: 0°-40°, when setting 1 does not manage a full coverage of the pool.
Setting nozzle angle and cleaner route Setting 3: 20°-20°, for round pools.
Note: These are the recommended settings. Different settings may work better for your pool.
4.
a.
Nozzle angle
Running route
Clean the filter tray
Open the cleaner by the clips
b. Take out the filter tray V. Trouble shooting VI.
VII.
This product has passed all quality control and safety tests, conducted by the technical department of the factory.
Warranty information:
1.
2.
3.
4.
5.
Packing list
Warranty
The warranty period is 12 months of use on the motors and electrical parts from the date of purchase and established under the terms
of the Consumer Code and the legal guarantee against hidden defects and vices in any case applies in the conditions of the articles in
the country of purchase.
The warranty is void if the product is handled or repaired by nonqualified person in unauthorized repair services.
Broken parts are not covered by the warranty.
The warranty only covers factory defects, it does not cover damage caused by misuse of the article.
Any claim made or repair made during the warranty period will be subject to mandatory presentation of the invoice.
- 12 -

Important Precautions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Do not power on the cleaner when it is out of the water.
Strictly prohibit using the cleaner beyond its operating conditions. Please read the manual carefully, and use it according to the manual.
We have no responsibility for any loss or injury caused by improper use.
Use the accessories recommended or sold by the manufacturer only.
This model mainly applies to swimming pools with a flat floor.
The cleaner should not be used by children under the age of 8 or people with mental disorders. Please do so under the supervision of
the guardian if necessary. Please do not allow children to ride on it or play as a toy.
Use the original and authorized power adapter only.
It must be replaced by the after-sale professionals if the power line is damaged.
The power line must be connected to a leakage protected and earthed socket when charging.
Do not operate the cleaner when there are people in the pool.
Always clean and wash the filter tray after use.
Power off the cleaner when maintaining, cleaning or not using it.
The cleaner should be stored in a cool and ventilated place, away from direct sunshine.
Charge the battery under the permitted condition. The cleaner should be stored in a cool place when charging, meanwhile do not
place or be covered with anything to prevent the damage of internal electrical components caused by overheating of the power unit.
Only professionals can disassemble the sealed driving kit of the cleaner.
Close the pool filtration system before use.
The cleaner should be charged every three months if it needs to be stored for a long time. Please use the original and authorized
adapter only to ensure that the battery power is maintained at 40%-60%. The battery voltage will be lower than the over-discharge
protection voltage due to the self-discharge of battery if not charging the battery for a long time, which will lead to fatal damage to the
battery if continuing too long. Please be careful.
Prohibit charging the battery under the condition of fire or extreme heat. Do not use or store the cleaner near the heat source.
Prohibit piercing the cleaner shell with nails or other sharp objects, and prohibit hammering, impacting and throwing the cleaner.
I.
The robotic pool cleaner Cyber is a new type of rechargeable automatic cleaning equipment for pools with the function of automatic
beaching.
The cleaning function is upgraded, and the half-way turn-back function is activated for 5-12 times every 20 times the wall is hit, so that
the center of the swimming pool is no longer a dead corner for cleaning.
Introduction III.Specifications IV.
1.
a.
b.
Operation instruction
Precautions
Install the brush before use to avoid possible dirt leaks.
Please ensure that the top cover of the cleaner is tightly assembled to its chassis.
c.
d.
e.
f.
g.
After turning on, the cleaner must be placed in the pool within 20 seconds
Put into or lift out of the pool with the cleaner bottom towards the wall to avoid any possible scratches to the pool.
Power off the cleaner after use.
Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting into or lifting out of the pool.
It is necessary to stay on the water surface for 10-15 seconds until water flows out from the cleaner to the pool before being placed on the ground.
g.
2.
a.
*
*
*
b.
*
Lift the handle or clips of the cleaner out from the pool.
Quick operation
Plug in the cleaner with the supplied adapter and charging line to charge the battery.
Turn the switch knob to OFF before charging.
Clean the charging port before charging.
Keep the machine charging port and the adapter dry when charging.
Turn the switch knob to power on or off the cleaner
Please put into water within 20 seconds after turning on.
c.
d.
e.
3.
There are two nozzles on the cleaner, one of them opens once the other closes. Water flows out through the open nozzle to thrust the
cleaner forward. Adjust the nozzle by turning it to control the cleaner route.
Turn the switch knob to ON, the cleaner is power-on and the indicator light is steady blue, then put it into water. About 15 seconds after
power-on, the cleaner begins to work, and the blue light flashes.
When battery power is low, the cleaner will move close to the pool wall. The red-light fast flashes. The cleaner stops running when it
runs out of battery.
Indicators
Functions and adjustment of nozzles
a.
The nozzles of the cleaner are marked with angles (0°-40°).
The cleaner moves in an approximately straight line when the nozzle angle is 0°.
The cleaner moves in a more curved line at a larger angle from 0°-40°.
Setting 1: default setting: 0°-20°, for most of pools.
Setting 2: 0°-40°, when setting 1 does not manage a full coverage of the pool.
Setting nozzle angle and cleaner route Setting 3: 20°-20°, for round pools.
Note: These are the recommended settings. Different settings may work better for your pool.
4.
a.
Clean the filter tray
Open the cleaner by the clips
b. Take out the filter tray V. Trouble shooting VI.
VII.
This product has passed all quality control and safety tests, conducted by the technical department of the factory.
Warranty information:
1.
2.
3.
4.
5.
Packing list
Warranty
The warranty period is 12 months of use on the motors and electrical parts from the date of purchase and established under the terms
of the Consumer Code and the legal guarantee against hidden defects and vices in any case applies in the conditions of the articles in
the country of purchase.
The warranty is void if the product is handled or repaired by nonqualified person in unauthorized repair services.
Broken parts are not covered by the warranty.
The warranty only covers factory defects, it does not cover damage caused by misuse of the article.
Any claim made or repair made during the warranty period will be subject to mandatory presentation of the invoice.
- 13 -
c.Clean the filter tray and chassis
d.Reassemble the cleaner e.Clap on the clips

Important Precautions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Do not power on the cleaner when it is out of the water.
Strictly prohibit using the cleaner beyond its operating conditions. Please read the manual carefully, and use it according to the manual.
We have no responsibility for any loss or injury caused by improper use.
Use the accessories recommended or sold by the manufacturer only.
This model mainly applies to swimming pools with a flat floor.
The cleaner should not be used by children under the age of 8 or people with mental disorders. Please do so under the supervision of
the guardian if necessary. Please do not allow children to ride on it or play as a toy.
Use the original and authorized power adapter only.
It must be replaced by the after-sale professionals if the power line is damaged.
The power line must be connected to a leakage protected and earthed socket when charging.
Do not operate the cleaner when there are people in the pool.
Always clean and wash the filter tray after use.
Power off the cleaner when maintaining, cleaning or not using it.
The cleaner should be stored in a cool and ventilated place, away from direct sunshine.
Charge the battery under the permitted condition. The cleaner should be stored in a cool place when charging, meanwhile do not
place or be covered with anything to prevent the damage of internal electrical components caused by overheating of the power unit.
Only professionals can disassemble the sealed driving kit of the cleaner.
Close the pool filtration system before use.
The cleaner should be charged every three months if it needs to be stored for a long time. Please use the original and authorized
adapter only to ensure that the battery power is maintained at 40%-60%. The battery voltage will be lower than the over-discharge
protection voltage due to the self-discharge of battery if not charging the battery for a long time, which will lead to fatal damage to the
battery if continuing too long. Please be careful.
Prohibit charging the battery under the condition of fire or extreme heat. Do not use or store the cleaner near the heat source.
Prohibit piercing the cleaner shell with nails or other sharp objects, and prohibit hammering, impacting and throwing the cleaner.
I.
The robotic pool cleaner Cyber is a new type of rechargeable automatic cleaning equipment for pools with the function of automatic
beaching.
The cleaning function is upgraded, and the half-way turn-back function is activated for 5-12 times every 20 times the wall is hit, so that
the center of the swimming pool is no longer a dead corner for cleaning.
Introduction III.Specifications IV.
1.
a.
b.
Operation instruction
Precautions
Install the brush before use to avoid possible dirt leaks.
Please ensure that the top cover of the cleaner is tightly assembled to its chassis.
c.
d.
e.
f.
g.
After turning on, the cleaner must be placed in the pool within 20 seconds
Put into or lift out of the pool with the cleaner bottom towards the wall to avoid any possible scratches to the pool.
Power off the cleaner after use.
Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting into or lifting out of the pool.
It is necessary to stay on the water surface for 10-15 seconds until water flows out from the cleaner to the pool before being placed on the ground.
g.
2.
a.
*
*
*
b.
*
Lift the handle or clips of the cleaner out from the pool.
Quick operation
Plug in the cleaner with the supplied adapter and charging line to charge the battery.
Turn the switch knob to OFF before charging.
Clean the charging port before charging.
Keep the machine charging port and the adapter dry when charging.
Turn the switch knob to power on or off the cleaner
Please put into water within 20 seconds after turning on.
c.
d.
e.
3.
There are two nozzles on the cleaner, one of them opens once the other closes. Water flows out through the open nozzle to thrust the
cleaner forward. Adjust the nozzle by turning it to control the cleaner route.
Turn the switch knob to ON, the cleaner is power-on and the indicator light is steady blue, then put it into water. About 15 seconds after
power-on, the cleaner begins to work, and the blue light flashes.
When battery power is low, the cleaner will move close to the pool wall. The red-light fast flashes. The cleaner stops running when it
runs out of battery.
Indicators
Functions and adjustment of nozzles
a.
The nozzles of the cleaner are marked with angles (0°-40°).
The cleaner moves in an approximately straight line when the nozzle angle is 0°.
The cleaner moves in a more curved line at a larger angle from 0°-40°.
Setting 1: default setting: 0°-20°, for most of pools.
Setting 2: 0°-40°, when setting 1 does not manage a full coverage of the pool.
Setting nozzle angle and cleaner route Setting 3: 20°-20°, for round pools.
Note: These are the recommended settings. Different settings may work better for your pool.
4.
a.
Clean the filter tray
Open the cleaner by the clips
b. Take out the filter tray V. Trouble shooting VI.
VII.
This product has passed all quality control and safety tests, conducted by the technical department of the factory.
Warranty information:
1.
2.
3.
4.
5.
Packing list
Warranty
The warranty period is 12 months of use on the motors and electrical parts from the date of purchase and established under the terms
of the Consumer Code and the legal guarantee against hidden defects and vices in any case applies in the conditions of the articles in
the country of purchase.
The warranty is void if the product is handled or repaired by nonqualified person in unauthorized repair services.
Broken parts are not covered by the warranty.
The warranty only covers factory defects, it does not cover damage caused by misuse of the article.
Any claim made or repair made during the warranty period will be subject to mandatory presentation of the invoice.
Symptom Possible reason
Internal fault
Pump protection
Battery protection
Adapter damage
Unsuitable nozzle angle
Special pool shape
Pool water filtration system is running
Not fully charged Fully charge the cleaner (needs to last
5-6 hours)
The pool slopes more than 15 degree. Warm Tips:Only suitable for flat-bottom
pools, not climbing walls or slopes more
than 15 degree.
Turn off water filtration system
Adjust nozzle to increase angle of
deflection
Charge the robot and in case it does not
work, please ask for after-sales service
Adjust nozzle angle
Contact after-sales service
Re-start the robot
Contact after-sales service
Solution
The cleaner does not work and the red
indicator light slowly flashes
The cleaner does not work and the blue
indicator light flashes
The cleaner does not work and the
indicator light does not flash
The cleaner does not achieve a full
coverage of the pool
The working time of the cleaner cannot
reach MAX 120 minutes
The cleaner cannot reach the shallow
water area from the deep water area
The adapter indicator light does not work
- 14 -

Important Precautions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Do not power on the cleaner when it is out of the water.
Strictly prohibit using the cleaner beyond its operating conditions. Please read the manual carefully, and use it according to the manual.
We have no responsibility for any loss or injury caused by improper use.
Use the accessories recommended or sold by the manufacturer only.
This model mainly applies to swimming pools with a flat floor.
The cleaner should not be used by children under the age of 8 or people with mental disorders. Please do so under the supervision of
the guardian if necessary. Please do not allow children to ride on it or play as a toy.
Use the original and authorized power adapter only.
It must be replaced by the after-sale professionals if the power line is damaged.
The power line must be connected to a leakage protected and earthed socket when charging.
Do not operate the cleaner when there are people in the pool.
Always clean and wash the filter tray after use.
Power off the cleaner when maintaining, cleaning or not using it.
The cleaner should be stored in a cool and ventilated place, away from direct sunshine.
Charge the battery under the permitted condition. The cleaner should be stored in a cool place when charging, meanwhile do not
place or be covered with anything to prevent the damage of internal electrical components caused by overheating of the power unit.
Only professionals can disassemble the sealed driving kit of the cleaner.
Close the pool filtration system before use.
The cleaner should be charged every three months if it needs to be stored for a long time. Please use the original and authorized
adapter only to ensure that the battery power is maintained at 40%-60%. The battery voltage will be lower than the over-discharge
protection voltage due to the self-discharge of battery if not charging the battery for a long time, which will lead to fatal damage to the
battery if continuing too long. Please be careful.
Prohibit charging the battery under the condition of fire or extreme heat. Do not use or store the cleaner near the heat source.
Prohibit piercing the cleaner shell with nails or other sharp objects, and prohibit hammering, impacting and throwing the cleaner.
I.
The robotic pool cleaner Cyber is a new type of rechargeable automatic cleaning equipment for pools with the function of automatic
beaching.
The cleaning function is upgraded, and the half-way turn-back function is activated for 5-12 times every 20 times the wall is hit, so that
the center of the swimming pool is no longer a dead corner for cleaning.
Introduction III.Specifications IV.
1.
a.
b.
Operation instruction
Precautions
Install the brush before use to avoid possible dirt leaks.
Please ensure that the top cover of the cleaner is tightly assembled to its chassis.
c.
d.
e.
f.
g.
After turning on, the cleaner must be placed in the pool within 20 seconds
Put into or lift out of the pool with the cleaner bottom towards the wall to avoid any possible scratches to the pool.
Power off the cleaner after use.
Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting into or lifting out of the pool.
It is necessary to stay on the water surface for 10-15 seconds until water flows out from the cleaner to the pool before being placed on the ground.
g.
2.
a.
*
*
*
b.
*
Lift the handle or clips of the cleaner out from the pool.
Quick operation
Plug in the cleaner with the supplied adapter and charging line to charge the battery.
Turn the switch knob to OFF before charging.
Clean the charging port before charging.
Keep the machine charging port and the adapter dry when charging.
Turn the switch knob to power on or off the cleaner
Please put into water within 20 seconds after turning on.
c.
d.
e.
3.
There are two nozzles on the cleaner, one of them opens once the other closes. Water flows out through the open nozzle to thrust the
cleaner forward. Adjust the nozzle by turning it to control the cleaner route.
Turn the switch knob to ON, the cleaner is power-on and the indicator light is steady blue, then put it into water. About 15 seconds after
power-on, the cleaner begins to work, and the blue light flashes.
When battery power is low, the cleaner will move close to the pool wall. The red-light fast flashes. The cleaner stops running when it
runs out of battery.
Indicators
Functions and adjustment of nozzles
a.
The nozzles of the cleaner are marked with angles (0°-40°).
The cleaner moves in an approximately straight line when the nozzle angle is 0°.
The cleaner moves in a more curved line at a larger angle from 0°-40°.
Setting 1: default setting: 0°-20°, for most of pools.
Setting 2: 0°-40°, when setting 1 does not manage a full coverage of the pool.
Setting nozzle angle and cleaner route Setting 3: 20°-20°, for round pools.
Note: These are the recommended settings. Different settings may work better for your pool.
4.
a.
Clean the filter tray
Open the cleaner by the clips
b. Take out the filter tray V. Trouble shooting VI.
VII.
This product has passed all quality control and safety tests, conducted by the technical department of the factory.
Warranty information:
1.
2.
3.
4.
5.
Packing list
Warranty
The warranty period is 12 months of use on the motors and electrical parts from the date of purchase and established under the terms
of the Consumer Code and the legal guarantee against hidden defects and vices in any case applies in the conditions of the articles in
the country of purchase.
The warranty is void if the product is handled or repaired by nonqualified person in unauthorized repair services.
Broken parts are not covered by the warranty.
The warranty only covers factory defects, it does not cover damage caused by misuse of the article.
Any claim made or repair made during the warranty period will be subject to mandatory presentation of the invoice.
Item
1
2
3
4
5
6
Name
Cleaner body
Charger
User manual
Brush
Tow rope
Floating handle
QTY (pc)
1
1
1
1
1
1
Remark
In carton
In plastic bag
In plastic bag
In plastic bag
In plastic bag
In plastic bag
- 15 -

- 16 -
12-Month Coverage
Your Warranty Includes
Within 12 months of purchase, we will provide timely and effective online after-sales
service. We will repair or replace any defective product (due to manufacturing fault)
within the warranty period.
How to Return Your Ofuzzi Product
Contact [email protected] with your order number.
We will issue you a return label for your return.
Tear off the 'Return Details' page and fill in the details. Include this inside your return
package.
We will issue your replacement/refund on receiving the return package.
Return Details
In order to process your return as quickly as possible, we require the following information.
Please fill out this form and include it in your return package.
Purchase Name:
Order Number:
Date of Purchase:
Your Email Address:
Place of Purchase:
[email protected]

[email protected]
Shenzhen Jiuheyu Technology Co., LTD.
Room 205, B11 Building, Yintian Industrial Zone, Yantian Community,
Xixiang Street, Bao'an District, Shenzhen, China 518000