Okina USA HUB-TF Quick start guide

HUB-TF_HUB-TFHB_rev042709
1
HUB-TF
HUB-TFHB
Operational Manual
Professional Camera Housing - Front Opening
80
* UL certification only refers to the power converter and the power module
Constructed from die-cast aluminum alloy and is powder coated with stove finish
IP67 Rating – designed and manufacturedto the highest technical standard with environmental protection
Fully-Cable Managed Bracket
Usesprofessional rust-proof stainless steel screws
Includes Heater & Blower for HUB-TFHB
24V AC, 40VA
FEATURES
PleasereadtheOperationalManual
before attempting to use this product.
HUB-TF HUB-TFHB

HUB-TF_HUB-TFHB_rev042709
2
1. Heater (Only for HUB-TFHB) 6. Cable conduits PGB11 x2
2. Heat Shield (Only for HUB-TFHB) 7. Captive retaining screws x4
3. Thermal control board 8. Heater & blower wires, Ground wire
4. Camera mounting platform 9. GroundWire
5. Terminal block assembly 10. Blower (Only for HUB-TFHB)
1. Use the rear section of the Mounting Bracket (D) as a template for marking the position on the wall of the
Mounting Holes (H). Remove & drill to pattern required.
2. Attach the Mounting Bracket arm to the wall using the raw plugs and screws provided.
3. Feedcables from the main Housing (C) through the hole of Mounting Plate (E) on the Mounting Bracket (D),
then feedcable again to concealed channel inside the Mounting Bracket throughout wall outlet (A) or bracket
outlet (B).
4. Attach the main Housing (C) to the Mounting Plate (E) of Bracket with 4 of 1/4" x 14.7mm Trilobular screws (F)
provided.
5. Release Screw (G) on the Mounting Bracket to pan and tilt the Housing. Position the Housing as required for the
correct Cameracoveragethen tighten both Screws to secure.
PART DESCRIPTION
MOUNTING CONFIGURATION
1
2
3
4
5
6
7
8
10
9

HUB-TF_HUB-TFHB_rev042709
3
1. Unscrew the 3 captive Retaining Screws (C) and remove the Housing Cover (A) from the Housing Base (B).
2. Release the 4 Keyhole Screws (F) and then slide and withdraw the Camera Platform (G) from the Housing
Base (B).
3. Mount the Camera (not included) (H) onto Platform (G) using the 1/4" UNC Screw (I) Supplied, ensuring that the
Insulation Pad (J) is mounted between the Platform and the Camera. Always check that the Camerais firmly
attachedto the Platform.
4. Connect the Camera/ Heaterpower cable to the rear TerminalBlock (E) through the first Cable Conduit (D)
referring to the circuit diagram shown in the WIRING DIAGRAM section of the manual for the terminal
designations.
5. Connect the video cable to the Camera through the second Cable Conduit (D).
FITTING INSTRUCTIONS
(A)
(
B)
(
C)
(
D)
(
E)
(F)

HUB-TF_HUB-TFHB_rev042709
4
The figure above shows the internal wiring diagram of the HUB-TF & HUB-TFHB for the window demister. A spare 6-way
terminal block is provided at the rear of the enclosure for the camera when necessary and lens connections. Circuit
identified as follows:
TB.1 6-way terminal block H.1 Heater 12V DC 9 
TB.2 3-way terminal block Heater 24V AC 9 
FTB.1 Fused terminal block Heater 110V AC 9 
FS.1 3 Amp Fuse Heater 30V AC 9 
STAT.1 28 Thermostat B.2 Blower 12V DC9 
STAT.2 35 Thermostat Blower 24V AC9 
P.C.B.1 Thermal control circuit board PSU Power supply unit 24V AC
WIRING DIAGRAM

HUB-TF_HUB-TFHB_rev042709
5
HUB-TF / HUB-TFHB:
Fully-Cable Managed Bracket:
Max Load: 3500g
Material: Die-cast aluminum alloy with light ivory powder coated and stove finish
Scan Angle: 180°
Tilt Angle: 90°
Net Weight: 900g
Fixing: 3 Screws with bushings
DIMENSIONS (mm)

HUB-TF_HUB-TFHB_rev042709
6
Model
HUB-TF
HUB-TFHB
IP Rating
IP67
Mounting Bracket
Full-Cable Management
Construction
Die-Cast Aluminum Alloy
Coating
Ivory Powder Stove
Heater
No
Yes
Blower
No
Yes
Required Power
Supply / Transformer *
No 24V AC (+/-10%), 40VA
Dimension
17.72”(L) x 5.31”(W) x 5.51”(H) / 450mm(L) x 135mm(W) x 140mm(H)
Weight
8.42lbs / 3820g (with bracket)
9.02 lbs / 4090g (with bracket)
* Power supply / transformer not included
One (1) HUB-TS or HUB-TSHB Camera Housing
One (1) Fully-Cable Managed Bracket
One (1) Operational Manual
One (1) Main Accessories Pack
Three (3) Rust-proof Stainless Steel Wall Screws
Three (3) Rust-proof Stainless Steel Mounting Screws
Three (3) Stainless Steel Washers
Three (3) Plastic Washers
One (1) Allen Wrench
One (1) Secondary Accessories Pack
Two (2)Rust-proof Stainless Steel Camera Mounting Screws
One (1) Rubber Pad
One (1) Plastic Washer
*For any returns, please include all components listed above with original packaging in Resalable Condition.
Absolutely No Returns will be accepted if any component is missing/damaged or if any cable is cut or tampered with.
OKINA USA Products are covered under warranty for one yearfrom the date of purchase. The warranty will
automatically be voided if any of the following occurs:
1. Product sticker is removed
If the product sticker is removed, we will not be able to confirm any information regarding when and where the
product was purchased. We have no other way to verify the purchase record without the serial number on the
product sticker; therefore, it should not be removed.
2. Product ismodified in any way
If the product is scratched, damaged, or modified in a manner not described in this manual, the warranty will be
voided immediately. It is the customer’s responsibility to keep the product in good condition.
3. Power cable is cut
The power cable and any other cable should not be tamperedwith. Cutting or modifying of the cables will result in
termination of the warranty.
GENERAL SPECIFICATIONS
PACKAGECONTENTS
WARRANTY

HUB-TF_HUB-TFHB_rev042709
7
Always unplug the top section of the earth wire from the base wire when disassembling the housing. Remember to plug
the top and bottom together again when reassembling the housing. UL certification refers only to power converter&
power module.
1. Read and follow instructions
All operating and user instructions should be read and followed before the unit is to be operated.
2. Secure all screws
Please make sure all rust-proof stainless steel screws are installed securely to ensure a waterproof seal.
3. Electrical connections
Only a qualified electrician should be allowed to make electrical connections.
4. Do not disassemble the product
Do not disassemble the product as it is dangerous and may cause damage to the product. Referall servicing to
qualified service personnel.
5. Handle the product with care
Be careful when handling the product. Do not drop it or subject it to strong shock or vibrations in order to prevent
any damage to the product. Do not handle the product in a wet environment or when your hands are wet.
6. Reducing risk
Toreduce risk of fire or electric shock, do not removecover. Donot open product in wet weather. No userserviceable
parts inside. Refer servicing to qualified service personnel.
7. Unpacking
Unpack carefully. Electronic components can be damagedif improperly handled or dropped. If an item appears to
have been damaged during shipment, please place it properly in its carton and notify the shipper.
8.Installationnotice
Tropical, coastal salt water environment:
If you plan to install this product into a tropical, sea, coastal salt water or corrosive industrial water/mist environment,
please seal each stainless screw and fitting with a silicon grease compound. This will help prevent electrolysis
corrosion occurring and extendthe lifespan of the product and housing and prevent premature deterioration.
IMPORTANT NOTE

HUB-TF_HUB-TFHB_rev042709
8