Okina USA SIR24X-348AIDN-VD Quick start guide

Copyright © 2009. All Rights Reserved.
http://www.okinausa.com REV0120809
SIR24X-348AIDN-VD 480 TVL
SIR24X-342AIDN-VD 420 TVL
Operational Manual
3-AXIS Day & Night Vandal Proof
IR Dome Camera
•1/3” Sony Super HAD CCD
•Employs Digital Signal Processor (DSP) IC for Image
Control
•24 IR LED
•3.3mm~12.0mm Aspherical Auto Iris Vari-Focal Lens
Made by Daiwon
•IR Distance up to 50ft / 15m
•0.3 Lux @ F2.0, 0 Lux @ IR “on” – 480 TVL
0.2 Lux @ F2.0, 0 Lux @ IR “on” – 420 TVL
•High Sensitivity, Low Smear, High Anti-Blooming
•IP66 Rating
•12V DC
1. Use the allen wrench to loosen the screws on the
tamper-resistant housing cover.
2. The unit has a factory installed side conduit entry and the
cables can be adjusted to the back conduit entry according
to installation requirement.
3. Set the mounting base onto the wall or ceiling and center
it over the mounting hole. Use the four screws to secure it
onto the wall/ceiling.
4. Camera Image Adjustment
First tilt then rotate the camera module to obtain desired
viewing angle. Then turn the horizontal adjustment ring to
correct the image.
Note: When adjusting 3-AXIS vari-focal lens, follow the Camera
Image Adjustment setup first. You must turn the horizontal
adjustment ring so that the shaded area is facing toward the top or
left side of you.
FEATURES
Please read the Operational Manual
before attempting to use this product.
DIMENSIONS
INSTALLATION
Shade Facin
g
Left
Shade Facing Top
PAL Version Also Available
(Ø)145mm 108.2mm

Copyright © 2009. All Rights Reserved.
http://www.okinausa.com REV0120809
5. When the camera focus adjustment is complete, use the
allen wrench to fasten the tamper-resistant housing to the
base.
6. When using the side conduit cabling, it is suggested to cover
the cables using metal conduit (to prevent external damage
and for waterproof prevention), and wined the waterproof
adhesive tape (P.T.F.E. Thread Seal Tape) onto the metal
conduit before installation.
7. Connect the video output to the monitor or other video
device through a 75 Ohms type coaxial cable and the DC
Jack or AC/DC Terminal to the power source.
Once the picture appears on the monitor, open the cover and adjust
the lens adjustor knobs “NEAR ←→ FAR”. Get the view zoom that
you desire, and then adjust the focus of the lens to obtain the best
picture. After adjustments, tighten both adjustor knobs.
Vari-Focal Lens Adjustment
DIP Switch Setting
•Flickerless
Set switch OFF/F.L. to Flicker to enable Flickerless function. In this
mode, the switch AES/OFF is auto disabled.
•AGC
Adjust the switch to AGC indicates AGC-Hi and OFF indicates
AGC-Low. AGC-Hi mode: The max. AGC gain is approximately 26dB.
AGC-Lo mode: The max. AGC gain is approximately 16dB.
•Auto Iris
When using an auto iris lens, the switch AES/OFF should be in the
OFF position. Adjust VR to the proper level.
•BLC
Set switch OFF/BLC to BLC to enable Back Light Compensation
function.
*Specifications are subject to change without notice
* For any returns, please include all components listed above with original
packaging in Resalable Condition. Absolutely No Returns will be
accepted if any component is missing/damaged.
Model SIR24X-348AIDN-VD SIR24X-342AIDN-VDP
Image Sensor 1/3” Sony Super HAD CCD
DSP Sony
Total Pixel NTSC: 768(H) x 694(V)
PAL: 500(H) x 562(V)
NTSC: 510(H) x 492(V)
PAL: 500(H) x 582(V)
Synchronizing
System Internal
Resolution 480 TV Lines 420 TV Lines
Minimum
Illumination 0.3 Lux @ F2.0 0 Lux @ IR “on”
0.2 Lux @ F2.0
0 Lux @ IR “on”
S/N Ratio More than 48dB
Flickerless NTSC: On / Off, 1/100s switchable
PAL: On / Off, 1/120s switchable
Auto Gain Control High / Low switchable
White Balance Auto 2500°K~9500°K
Back Light
Compensation On / Off switchable
Gamma 0.45
Electronic Shutter NTSC: 1/60~1/100,000sec switchable
PAL: 1/50~1/110,000sec switchable
Video Output 1Vp-p composite / 75 Ω
Lens 3.3mm~12.0mm Aspherical Auto Iris
Vari-Focal Lens / F1.6~360 Made by Daiwon
Wide: 83.9°x61.9° / Tele: 23.0°x17.9° (HxV)
IR LED 24 IR LED
IR Wavelength 850 nm
IR Distance 50ft / 15m
IP Rating IP66
Power Supply 12V DC + 10%
Power
Consumption 440mA @ IR “on” 180mA @ IR “off”
440mA @ IR “on”
160mA @ IR “off”
Operating
Temperature 14°F ~ 122°F / -10°C ~ +50°C
Dimension 5.7”(Ø) x 4.3”(H)
145mm(Ø) x 108.2mm(H)
SPECIFICATIONS
To Monitor
To DC 12V Power Source
OPERATION

Copyright © 2009. All Rights Reserved.
http://www.okinausa.com REV0120809
zOne (1) SIR24X-348AIDN-VD/SIR24X-348AIDN-VDP or
SIR24X-342AIDN-VD/SIR24X-342AIDN-VDP Dome Camera with
power/video cable
zFour (4) Screws
zOne (1) Allen Wrench
zOne (1) Operational Manual
1. Never point the camera toward the sun
Do not expose the lens directly to the sun or to strong light as this
may damage the pick-up device.
2. Handle this camera with care
Avoid any shock or bumping of the camera. Improper handling
could damage the camera.
3. Requires a proper operating environment
This camera is designed for indoor use. The allowable
temperature range for operation of this camera is between
-4°F ~ 122°F / -10°C ~ 50°C and the allowable humidity is
85%RH maximum.
4. Clean the front face or lens
It is recommended that the surface be cleaned every 3~6 months.
Cleaning should be done by using a chamois, a very fine soft
cloth, lens tissue, or cotton tipped applicator and ethanol to
carefully remove any fingerprint or dust.
5. Check the power source voltage
The power source voltage should be within the specified range.
(Camera must meet the specifications). Camera must be
connected to a surge protector at all times.
6. Objects and liquid entry
Never push objects of any kind into this camera as this may touch
dangerous voltage points of short out parts that could result in a
fire or electric shock. Never spill any kind of liquid on the video
product.
7. Servicing
Do not attempt to service this video product by yourself as
opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all service to qualified servicing
personnel.
8. Damage requiring service
Unplug this video product from the wall outlet and refer service
to qualified servicing personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
video product.
c. If the video product has been exposed to rain or water.
d. If the video product has been dropped or the cabinet has
been damaged.
e. When the video product exhibits a distinct change in
performance.
OKINA USA products are covered under warranty for one year
from the date of purchase. The warranty will automatically be
voided if any of the following occurs:
1. Camera sticker is removed
If the camera sticker is removed, we will not be able to confirm
any information regarding when and where the product was
purchased. We have no other way to verify the purchase record
without the serial number on the camera sticker; therefore, it
should not be removed.
2.
Camera is modified in any way
If the camera is scratched, damaged, or modified in a manner
not described in this manual, the warranty will be voided
immediately. It is the customer’s responsibility to keep the
camera in good condition.
3. Video or power cable is cut
The video cable and the power cable should not be tampered
with. Cutting or modifying of the cables will result in
termination of the warranty.
PACKAGE CONTENTS
CAUTION
LIMITED WARRANTY