Okina SEMI96-600LP025 User manual

Copyright © 2010. All Rights Reserved.
http://www.okinausa.com REV12072010
SEMI96-600LP025 25.0mm lens
SEMI96-600LP 050 50.0mm lens
SEMI96-600LP 075 75.0mm lens
SEMI96-600LP025P 25.0mm lens
SEMI96-600LP 050P 50.0mm lens
SEMI96-600LP 075P 75.0mm lens
License Plate Capture Series
96 IR LED License Plate Monochrome Camera
z1/2” Sony Exview CCD
z600 TV Lines
z96 High Efficiency IR LED
zIR Distance up to 230ft
z25.0mm or 50.0mm or 75.0mm Lens Options
z0 Lux @ IR “on”
zHeavy Duty Die-Cast Aluminum Housing
Exceptional single-control technology reduces power consumption and extends LED life.
FEATURES
Please read the Operational Manual
before attempting to use this product.
L
O
N
G
-LIFE LED
MANUAL
zThe B/W Camera aims for LPR (License Plate
Recognition) / ANPR (Automatic Number Plate
Recognition) applications
zRS485 to control through DVR or joystick
zPelco P or D Protocols
zHeater & Blower
z24V AC
P = PAL Version

Copyright © 2010. All Rights Reserved.
http://www.okinausa.com REV12072010
PIC L-813 L-814 L-815
Model SEMI96-600LP025 SEMI96-600LP025P SEMI96-600LP050 SEMI96-600LP050P
SEMI96-600LP075 SEMI96-600LP075P
TV System NTSC PAL NTSC PAL NTSC PAL
Image Sensor 1/2” Sony CCD
DSP Sony
Resolution 600 TV Lines
Total Pixels 768(H) x 494(V) 752(H) x 582(V) 768(H) x 494(V) 752(H) x 582(V) 768(H) x 494(V) 752(H) x 582(V)
Video Output 1.0Vp-p Composite / 75ohms
Minimum
Illumination 0 Lux @ IR “on” (works in total darkness)
Imaging Area 7.4mm x 5.95mm
Scan System 2:1 Interlace
V: 59.9Hz ; H: 15.734KHz 2:1 Interlace V: 50Hz ; H: 15.625KHz
Synchronization Internal / Line Lock (AC Input Only)
Lens 25.0mm Lens 50.0mm Lens 75.0mm Lens
Gain Control 0 / 6 / 12 / 15 / 18 / 24 / 30
IR LED Superior power: 96 pcs IR LED
Metaphase Type LEDs, high-efficient array
IR Distance Up to 230ft / 70m
IR View Angle 6°
S/N Ratio More than 50dB (AGC OFF)
Gamma 0.45
Auto
1/60~1/100,000sec Auto 1/50~1/100,000sec Auto 1/60~1/100,000sec Auto 1/50~1/100,000sec Auto 1/60~1/100,000sec Auto 1/50~1/100,000sec
Electronic Shutter
Speed Manual 9 steps (1/60(1/50), 1/100, 1/250, 1/500, 1/1K, 1/2K, 1/4K, 1/10K, 1/100Ksec)
Aperture High / Mid / Low
OSD Yes
Remote Control RS485 via Pelco P/D
IP Rating IP66
Power Supply 24V AC
Power
Consumption 85W
Operation Temp. -20ºF ~ 140ºF / -30ºC ~ +60ºC
Storage Humidity 30~90% RH
Storage Temp. -4ºF ~ 140ºF / -20ºC ~ +60ºC
Dimension 19.45”(W) x 18.11”(D)x 12.87”(H) / 494mm(W) x 460mm(D) x 327mm(H)
Weight 13.5 lbs / 6.1kg
*Specifications are subject to change without notice
zOne (1) SEMI96-600LP025/SEMI96-600LP025P, or SEMI96-600LP050/SEMI96-600LP050P, or
SEMI96-600LP075/SEMI96-600LP075P Camera
zOne (1) Manual
*For any returns, please include all components listed above with original packaging in Resalable Condition. Absolutely No
Returns will be accepted if any component is missing/damaged or if any cable is cut or tampered with.
SPECIFICATIONS
PA
C
KA
G
E
CO
NTENT
S

Copyright © 2010. All Rights Reserved.
http://www.okinausa.com REV12072010
1. Never point the camera toward the sun
Do not expose the lens directly to the sun or to strong light as this may damage the pick-up device.
2. Handle this camera with care
Avoid any shock or bumping of the camera. Improper handling could damage the camera.
3. Requires a proper operating environment
This camera is designed for outdoor or indoor use. The allowable temperature range for operation of this camera is between 14°F
~ 122°F / -10°C ~ 50°C and the allowable humidity is 85%RH maximum.
4. Clean the front face or lens
It is recommended that the lens be cleaned every 3~6 months. Cleaning should be done by using a chamois, a very fine soft cloth,
lens tissue, or cotton tipped applicator and rubbing alcohol to carefully remove any fingerprint or dust.
5. Check the power source voltage
The power source voltage should be within the specified range. (Camera must meet the specifications). Camera must be
connected to a surge protector at all times.
6. Objects and liquid entry
Never push objects of any kind into this camera as this may touch dangerous voltage points of short out parts that could result in
a fire or electric shock. Never spill any kind of liquid on the video product.
7. Servicing
Do not attempt to service this video product by yourself as opening or removing covers may expose you to dangerous voltage or
other hazards. Refer all service to qualified servicing personnel.
8. Damage requiring service
Unplug this video product from the wall outlet and refer service to qualified servicing personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video product.
c. If the video product has been dropped or the cabinet has been damaged.
d. When the video product exhibits a distinct change in performance.
OKINA USA products are covered under warranty for one year from the date of purchase. The warranty will automatically be voided
if any of the following occurs:
1. Camera sticker is removed
If the camera sticker is removed, we will not be able to confirm any information regarding when and where the product was
purchased. We have no other way to verify the purchase record without the serial number on the camera sticker; therefore, it
should not be removed.
2.
Camera is modified in any way
If the camera is scratched, damaged, or modified in a manner not described in this manual, the warranty will be voided
immediately. It is the customer’s responsibility to keep the camera in good condition.
3. Video or power cable is cut
The video cable and the power cable should not be tampered with. Cutting or modifying of the cables will result in termination of
the warranty.
CAUTION
WARRANTY