Olide M-701W User manual

Led Indicators And Wiring Instruction
5
Standby state
Receive a
matchable
tag signal
Receive a matched
tag signal and output
opening signal
Red indicator flashes
Receive the sensor's sensing signal
and output opening signal
Sensor
Tag
Wiring Instruction
COM
NO
AC/DC
12~30V
Power input
BLUE
GREEN
RED
BLACK
Relay NO
contact
Thanks for your purchasing, please refer to the following manual carefully before using.
Safety Instructions
1
Operation Instructions Make your choice...
M-701W Electronic identity sensor
M-701W M-701WM-701(0) M-701C(0)
Product Dimension
3
132 mm 72 mm31 mm
48.7 mm
46 mm
46 mm
11 mm 38 mm
58 mm
12 mm
Installation Instruction
4
Receiver: 1. Pry and open the housing by a screwdriver along the notch on the bottom of the receiver.
2. Drill two mounting fixing holes and one cable hole according to the size drawing, in the
appropriate position on the door head where the receiver needs to be installed.
3. Fix the receiver with the provided screws bag.
4. Thread the cable through the hole with the attached cable carefully.
5. After debugging, buckle the cover tightly.
Tag: M-701(0): Remove the screws, pry and open the housing by a screwdriver along the notch on
the side, and fasten the screws after installing the battery.
M-701C(0): Plug it into the USB port of the forklift or robot.
NOTE: Please don't install the receiver on the metal surface, or place it
behind the metal baffle, it will affect the sensing range.
Product Overall
2
Tag:
Tag's function key
Tag's operating indicator lights
Tag's operating indicator lights
Tag USB interface
Sensor:
LED indicator Function button
Mounting
holes
Connection
terminal
Mounting
holes
Wi-Fi indicators light (Green)
Action indicator light (Blue)
Power input indicator light (Red)
Wi-Fi connection
mode
Red indicator
always on
Red indicator
flashes
Blue indicator
always on
Green indicator
flashes
Green indicator
always on
Wi-Fi connection
successfully

Packing List
8
NO.
1
2
3
4
5
Name
Receiver
4-PIN cable
Screws bag
Manual
Tag
Quantity
1
1
1
1
Optional
Remark
165mm
Function Instructions
6
1, Learning method
Press the recognizer's function setting key, the red indicator light turns to blue LED indicator, within 5 seconds, press the tag's setting key, blue indicator
light of recognizer flashes 3 times, learning is successful, up to 200pcs tags can be matched.
2, Delete method
Press and hold the recognizer's setting key, until blue indicator light of recognizer flashes slowly, then release it, blue indicator lights is always on, wait
for the blue lights turns to red lights, all tags will be deleted. (Note: press for 5 seconds, blue light flashes slowly, press for 10 seconds, blue light flashes
quickly)
3, Sensing distance setting
Sensing distance with 3 levels: the 1st level is 1 meter, the 2nd level is 3 meters, the 3rd level is 5 meters. Press and hold the recognizer's setting key,
the tag's indicator light flashes once, twice, three times, once.....form a cycle. When the tag's indicator light flashes once, and release the setting key,
that is in the 1st level. Flash twice means in the 2nd level; flash three times means in the 3rd level.
When the distance between the two adjacent doors is less than 4 meters, the tag sensing invalid and the door
does not open, please try to reduce sensing distance of the tag.
Technical parameters
7
Recognizer
Access authorization: Learning code
The min distance between door and door: 4 meters
The max quantity of the tag: 300pcs
Output signal: COM, NO, Dry contact
Output delay time: 2.5 seconds
Power supply: AC/DC 12~30V
Action current: 229mA
Dimension: 132mm(L)x48.7mm(W)x31(H)mm
Tag
Power supply(701(0)): 3V (CR2032 cell buttons)
Power supply(701C(0)): 5V
Standby current: 10μA
Transmitting current: 2mA
Launch range: Three levels adjustable (1,3,5 meters)
Dimension(701(0)): 46mm(L)x46mm(W)x11mm(H)
Dimension(701C(0)): 58mm(L)x38mm(W)x12mm(H)
Scene two: Plug in and connect by USB port
001 003002
≥4m ≥4m
Scene one: carry it portably and no need to plug in
001 003002
≥4m ≥4m
When the person carrying the tag enters the sensing range of
the Door 002, the Door 002 will be opened automatically. The
people stay in the sensing range, Door 002 will always stay
opening until people leave the sensing range.
When the car carrying the tag enters the sensing range of the
Door 002, the Door 002 will be opened automatically. The car
stay in the sensing range, Door 002 will always stay opening
until car leave the sensing range.

Networking setting
9
Step 2: Open this APP, click "Add Device".
Step 5: Press and hold the sensor's function
button until the Blue indicator light flashes, after
10 seconds and Green indicator light will quick
flashes, then click "Confirm the indicator is
blinking rapidly" on the phone interface.
Step 3: In the "Electrical" category, find
the "Switch" group, select "Switch(Wi-Fi)"
and click "Next".
Step 6: Choose "Blink Quickly”
Step 1: Please search "Tuya Smart" APP
in your mobile App market, click "GET" to
install.
Step 4: Select the 2.4GHz Wi-Fi network
and enter your password, click "Next".

System setting page function
10
■ Device name: The current device's name, can be changed at any time.
■ Device information: Virtual ID, IP address, device time zone, signal strength.
■ Share device: Share the current device to other users.
■ Create a group: Compose multiple devices into a group. After forming a group, you can open the door at the same time by operating multiple
devices through the group icon.
■ Add to Home Screen: Adds the current switch shortcut keys to the home screen.
■ Device Upgrade: Displays the current firmware version of the device, which should be updated when a new version is available.
■ Delete the device: After deleting the device, the device will erase the network settings and restore factory settings.
Step 8: The device was added successfully
(if you need to change the device name, you
can click the icon behind the "WIFI
SWITCH" to modify it).
Step 11: Click "Add Sharing".Step 10: Click the icon in the upper right
corner, entering "System setting" interface,
click "Share Device", can share the current
device to other users.
Step 7: Wait for the network connection to
pair.
Step 9: Click Switch, the door will open.
Step 12: Click "Share with the Account
Tuya Smart".