Olympia Faucets, Inc. L-7220 User manual

INSTALLATION
Tools:
Adjustable Wrench Plumbers Putty Teon Tape Rags
Model Number: L-7220, L-7221, L-7222, L-7290, L-7291
L-7292, L-7280, L-7282, L-7250, L-7251, L-7251G
OLYMPIA FAUCETS, INC.
Interchange City Distribution Center #20
1277 Heil Quaker Boulevard
La Vergne, TN 37086
[phone]
www.olympiafaucets.com
Installation Steps:
Two Handle Lavatory Faucet
(1) Shut off water supplies. Remove old faucet.
Clean mounting surface in preparation for new
faucet.
(2) Place the faucet in position on the sink.
Apply plumbers putty under the base gasket.
Install washer on shanks and tighten with
locknut.
(3a) when using ball-nose exible supplies
to connect faucet to water supply valves, slip
coupling nut onto exible supply. Ball-nose
coupling will go partially into shank. Tighten
coupling nut (DO NOT OVERTIGHTEN).
Install opposite end according to
manufacturer’s instruction for both tubes.
(3b) when using stainless steel braided
faucet supply hose; this faucet requires one
end of the supply hose to have a ½” female
IPS connection. The other end of this supply
hose must match the thread on the water
supply valve under your sink. Once you’ve
identied the required size, carefully follow
the manufacturer’s installation instructions for
each hose.
(4) Important: After installation is complete,
remove aerator. Turn water supplies on and
allow both hot and cold water to run at least
one minute each. While water is running,
check for leaks. Turn off water and replace
aerator.
Pop-up Drain Installation:
(1) Remove pop-up ange from body
(2) Place a ring of putty on the bottom of
ange.
(3) Insert pop-up ange through drain hole
and attach fIange to body. Ensure the pop-up
outlet faces towards the back of the slnk
Tíghten the locknut securely with a wrench Do
not overtighten.
(5) Remove pivot rod nut from pop-up body,
ensure the washers is in place, insert pivot
rod, tighten pivot rod nut back to pop-up body.
(4) Remove the excess putty. Connect the
trap (check manufacturer’s instructions for
ínstallation)
Warnings and Notes:
Check with local plumbing code requirements before installation.
This product should be installed by a local listed plumber.
Do not use plumbers putty on threads.

Exploded Drawing:
A6
5
6
A1
1
2
A2
3
A3
4
A5
A4
B
C
D
F
G
E
H
2
ITEM # DESCRIPTION
A1 OP-190003C,H Acrylic Handle Cold,Hot
A2 OP-190004C,H Mini Blade Handle Cold, Hot
A3 OP-190006C,H Handle Hub
A4 OP-490017 Chrome Insert
A5 OP-490018 Acrylic White Insert
A6 OP-190005C,H Wrist Blade Handle Cold, Hot
BOP-490040 Bonnet Nut
COP-390004
OP-390005
Stem Unit-Brass Post
Stem Unit-Plastic Post
DOP-490041 Spring and Seats
E OP-490035 1.5 GPM Aerator
F OP-590003 Mounting Locknuts & Washers
GOP-590001 Supply Nuts
HOP-630004
OP-630002
50/50 Pop-Up Drain Assembly
Brass Pop-Up Drain Assembly
For more care information or trouble shooting
inquiries about your Olympia product, Please call:
OLYMPIA FAUCETS, INC. [phone]
8AM - 8PM EST (5AM to 5PM PST)
www.olympiafaucets.com
ITEM # DESCRIPTION
1OP-490012C,H Acrylic Handle Button Cold, Hot
2OP-490014 Screw
3OP-490013C,H Mini Blade Handle Button Cold, Hot
4OP-490042 Handle Hub Screw
5OP-490015 Handle Screw
6OP-490016C,H Wrist Blade Handle Button Cold,
Hot
(6) Push pivot rod down, insert drain plug
carefully. Test to ensure drain plug works
properly.
(7) Connect lift rod strap to pivot rod by using
clip. Tighten the thumbscrew to connect lift rod
strap to pop-up lift rod.