Omega Metal Liner and Decorative Wood Hood User manual

I M P O R T A N T
INSTALLATION INSTRUCTIONS FOR
OMEGA INDUSTRIES, INC.’s
METAL LINER AND DECORATIVE WOOD HOOD
Before installation may begin, the following components are required:
• Fan unit, part number 90026WHI1
• Blower unit, part number 90039WHI1
• Ducting System • Metal Liner • Decorative Wood Hood
A. The Wood Hood is composed of three separate components:
1. The decorative Hood Front.
2. Optional galley rail (shipped unattached).
3. T-shaped Metal Liner, Figure 2.
NOTE: T-shaped liner shipped with unit as standard. Rectangular
shaped metal liner available for on-site Wood Hood construction, Fig-
ure 4.
4. Theventilationsystem(powermoduleandductingsystem)is
not included and must be purchased separately.
B. Installation: Metal Liner – T-Shaped, Figure 3
1. Measureup61/8from thebottomof adjacentcabinets.Scribe
a level line horizontally across depth of both cabinets.
2. Raise Metal Liner so that bottom edge of liner is level with
scribed lines. Use four (4) #8 x 1/2” screws provided to attach
liner to adjacent cabinets through pre-drilled holes in liner. (If
metal liner is not flush to cabinet sidewalls, it may be neces-
sary to use a filler piece to avoid bowing the liner.) Locate
studs and place two #8 x 1 1/4”, supplied, through rear of
liner.
C. Installation of Omega Industries, Inc.’s decorative
Wood Hood:
1. Slide decorative hood front into position over T-Shaped liner
and between adjacent cabinets. Install the hood front by ad-
joiningtoadjacentcabinetsthroughthefront frames using (4)
#8 x 2 1/2” screws (not provided).
Form OME-03 12/2002 ©2002 Omega Industries, Inc.
Figure 1
Figure 2
Figure 3

D. Installation – Galley Rail
1. Anunattachedoptional Galley Rail assembly may be enclosed
with the decorative hood front. The Galley Rail should be at-
tached as shown in Figure 1. NOTE: All screw holes should
be pre-drilled. Exercise caution if nailing to avoid damage.
E. Installation of Rectangular Metal Liner (Figure 4) (used for on-
site construction of decorative Wood Hood)
1. Measure down 23 7/8” from top of adjacent cabinets. Scribe a
level line horizontally across depth of both cabinets.
2. Place bottom edge of 3/4” x 4” x 11 1/4” long wood filler block
along scribe line. Make sure filler block is tight against back
wall, Figure 5.
3. Usefour(4)#8x 1” screws,supplied,and fasten the two wood
filler blocks to adjacent cabinets.
4. Raise liner so bottom is level with scribed lines. Fasten liner to
fillerblock bydriving four (4)#8 x1/2”screws, supplied,through
pre-drilled holes (2 per side) in liner, Figure 6.
5. Locate studs and place #8 x 1 1/4” screws, supplied, through
rear of liner into stud.
F. Installation of Power Units
90026WHI1 Fan Unit – see installation instructions enclosed with
each Power Unit.
90039WHI1Blower Unit - seeinstallationinstructions enclosed with
each Power Unit.
Source for all parts listed:
Your local distributor or: Omega Industries, Inc., 1010 Rowe Street,
Elkhart, IN 46516 •574-295-5353 or 574-295-5329(fax)
Form OME-03 12/2002 ©2002 Omega Industries, Inc.
Figure 4
Figure 5
Figure 6