Whirlpool WVU57UC0F Product information sheet

30" (76.2 CM) AND 36" (91.4 CM) RANGE HOOD
Installation Instructions and Use & Care Guide
For questions about features, operation/performance, parts, accessories or service, call: 1-800-253-1301
or visit our website at www.whirlpool.com
In Canada, call 1-800-807-6777 or visit our website at www.whirlpool.ca
HOTTE D’ASPIRATION DE
30" (76,2 CM) ET 36" (91,4 CM)
Instructions d’installation et Guide d’utilisation et d’entretien
Au Canada, pour assistance, installation ou service, composer
le 1-800-807-6777 ou visiter notre site Web à
www.whirlpool.ca
Table of Contents/Table des matières.............................................................................2
LIB0120490/W10907171A
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.
FOR RESIDENTIAL USE ONL
Y.
IMPOR
TANT : LIRE ET CONSERVER CES INSTRUCTIONS.
POUR UTILISA
TION RÉSIDENTIELLE UNIQUEMENT
.
Models/Modèles:
WVU57UC0F/WVU57UC6F

2
TABLE OF CONTENTS TABLE DES MATIÈRES
RANGE HOOD SAFETY .................................................................3
INSTALLATION REQUIREMENTS.................................................5
Tools and Parts.............................................................................5
Location Requirements................................................................5
Venting Requirements..................................................................6
Electrical Requirements ...............................................................7
INSTALLATION INSTRUCTIONS...................................................8
Prepare Location..........................................................................8
Prepare Range Hood .................................................................10
Install Range Hood.....................................................................12
Make Electrical Connection .......................................................13
Complete Installation .................................................................14
RANGE HOOD USE......................................................................14
Range Hood Controls ................................................................14
RANGE HOOD CARE...................................................................15
Cleaning .....................................................................................15
WIRING DIAGRAM .......................................................................16
ASSISTANCE OR SERVICE.........................................................17
In the U.S.A. ...............................................................................17
In Canada ...................................................................................17
Accessories................................................................................17
WARRANTY ..................................................................................18
SÉCURITÉ DE LA HOTTE............................................................20
EXIGENCES D’INSTALLATION ...................................................22
Outils et pièces...........................................................................22
Exigences d’emplacement.........................................................22
Exigences concernant l’évacuation...........................................23
Spécifications électriques..........................................................24
INSTRUCTIONS D’INSTALLATION.............................................25
Préparation de l’emplacement...................................................25
Préparation de la hotte...............................................................27
Installation de la hotte................................................................29
Raccordement électrique...........................................................30
Terminer l’installation..................................................................31
UTILISATION DE LA HOTTE .......................................................31
Commandes de la hotte.............................................................31
ENTRETIEN DE LA HOTTE .........................................................32
Nettoyage...................................................................................32
SCHÉMA DE CÂBLAGE...............................................................33
ASSISTANCE OU SERVICE.........................................................34
Aux É.-U. ....................................................................................34
Au Canada..................................................................................34
Accessoires................................................................................34
GARANTIE.....................................................................................35

3
RANGE HOOD SAFETY
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.

4
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS

5
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
■Drill
■1¹⁄4" (3.0 cm) drill bit
■¹⁄8" (3.0 mm) drill bit for pilot holes
■Pencil
■Wire stripper or utility knife
■Tape measure or ruler
■Caulking gun and weatherproof caulking com"und
■Flat-blade screwdriver
■Phillips screwdriver
■Saber or keyhole saw
■Metal snips
Parts supplied
Remove parts from package. Check that all parts are included.
■#8-18 x 1" (4.2 mm x 25 mm) flat-head screws (2)
■#8-18 x 5/8" (4.2 mm x 16 mm) truss-head screws (4)
■Drywall anchors (2)
■Mounting brackets (2)
■9/64" x 13/64" (3.5 mm x 5 mm) T10-head screws (2)
■T10 TORX®† adapter (1)
■3 1/4" x 10" (8.3 cm x 25.4 cm) rectangular air transition (1)
■Regular air damper (1)
Parts needed
■Wall or roof cap with damper to match vent system
■3 - UL Listed wire connectors
■Vent clamps/duct tape as required
For 7" (17.8 cm) round vented installations:
■7" (17.8 cm) round metal vent system
For 3¹⁄4" x 10" (8.3 cm x 25.4 cm) rectangular vented
installations:
■3¹⁄4" x 10" (8.3 cm x 25.4 cm) rectangular metal vent system
For non-vented (recirculation) installations:
■Charcoal filter kit. For information on ordering, see the
“Accessories” section.
†®TORX is a registered trademark of Acument Intellectual Properties, LLC.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
■It is the installer’s responsibility to comply with installation
clearances specified on the model/serial/rating plate. The
model/serial/rating plate is located inside the range hood on
the left wall.
■Range hood location should be away from strong draft areas,
such as windows, doors, and strong heating vents.
■Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance. Consult the
cooktop/range manufacturer installation instructions before
making any cutouts.
■This range hood is recommended for use with cooktops with
a maximum total rating of 55,000 BTUs or less.
■Grounded electrical outlet is required. See the “Electrical
Requirements” section.
■All openings in ceiling and wall where range hood will be
installed must be sealed.
■These range hoods are factory set for vented installations.
Models that are capable of being installed as non-vented
(recirculating) require charcoal filters. See the “Accessories”
section to order charcoal filter kit.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local
codes.
Product Dimensions
Centerline
A
BC
D
E
F
G
H
I
I
A. 619/54" (16 cm)
B. 2" (5 cm)
C. 825/64" (21.3 cm)
D. 1" (2.54 cm)
E. 832/32" (22.8 cm)
F. 1911/16" (50 cm)
G. 11/2" (3.8 cm)
H. 36" (91.4 cm)
30" (76.2 cm)
I. 55/64" (2.2 cm)

6
Installation Clearances
A. 18" (45.7 cm) min. clearance - upper cabinet to countertop
B. 24" (61.0 cm) minimum - bottom of range hood to cooking surface
C. 30" (76.2 cm) min. cabinet opening width for 30" (76.2 cm) models
36" (91.4 cm) min. cabinet opening width for 36" (91.4 cm) models
D. 12" (30.5 cm) minimum cabinet depth
E. 36" (91.4 cm) base cabinet height
Venting Requirements
■This range hood is factory set to exhaust the air to
the outside through the wall or the roof. A non-vented
(recirculating) installation will require a Charcoal Filter Kit.
See the “Accessories” section for ordering information.
■Vent system must terminate to the outdoors, except for
nonvented (recirculating) installations.
■Do not terminate the vent system in an attic or other
enclosed area.
■Do not use a 4" (10.2 cm) laundry-type wall cap.
■Use a 7" (17.8 cm) round metal vent or a 3¹⁄4" x 10"
(8.3 cm x 25.4 cm) rectangular metal vent, depending
on your installation requirements. Rigid metal vent
is recommended. Plastic or metal foil vent is not
recommended.
■The length of vent system and number of elbows should be
kept to a minimum to provide efficient performance.
For the most efficient and quiet operation:
■Use no more than three 90° elbows.
■Make sure there is a minimum of 24" (61 cm) of straight vent
between the elbows if more than 1 elbow is used.
■Do not install 2 elbows together.
■Use clamps or duct tape to seal all joints in the vent system.
■The vent system must have a damper. If roof or wall cap has
a damper, do not use damper supplied with the range hood.
■Use caulking to seal exterior wall or roof opening around
the cap.
Cold Weather Installations
An additional back draft damper should be installed to minimize
backward cold air flow and a thermal break should be installed
to minimize conduction of outside temperatures as part of the
vent system. The damper should be on the cold air side of the
thermal break.
The break should be as close as possible to where the vent
system enters the heated portion of the house.
Makeup Air
Local building codes may require the use of makeup air systems
when using ventilation systems greater than specified CFM of
air movement. The specified CFM varies from locale to locale.
Consult your HVAC professional for specific requirements in your
area.
Venting Methods
Vent system can terminate either through the roof or wall. Use
3¹⁄4" x 10" (8.3 cm x 25.4 cm) rectangular with a maximum vent
length of 35 ft (10.7 m) or 7" (17.8 cm) or larger round vent with
a maximum length of 50 ft (15.2 m) for vent system.
NOTE: Flexible vent is not recommended. Flexible vent creates
both back pressure and air turbulence that greatly reduce
performance.
A. 7" (17.8 cm) round vent through roof or 31⁄4" x 10"
(8.3 cm x 25.4 cm) rectangular vent through the roof
or wall (purchased separately)
B. Roof/Wall cap with damper (purchased separately)
C. 24" (61.0 cm) min. above the cooking surface
D. Charcoal Filter Kit (purchased separately)
E. Recirculating grid
C
A
B
D
E
Roof Venting Wall Venting Recirculating
B
A
C
B
A
C
C
D
E

7
Calculating Vent System Length
To calculate the length of the system you need, add the
equivalent feet (meters) for each vent piece used in the system.
7" (17.8 cm) Round Vent System
Vent Piece Round
45° elbow 2.5 ft
(0.8 m)
90° elbow 5.0 ft
(1.5 m)
7" (17.8 cm) wall cap 0.0 ft
(0.0 m)
3¹⁄4" x 10" (8.3 cm x 25.4 cm)
to 7" (17.8 cm) 4.5 ft (1.4 m)
3¹⁄4" x 10" (8.3 cm x 25.4 cm)
to 7" (17.8 cm) 90° elbow 5.0 ft (1.5 m)
Example vent system
Maximum Recommended Length = 50 ft (15.2 m)
1 - 90° elbow = 5.0 ft (1.5 m)
1 - wall cap = 0.0 ft (0.0 m)
8 ft (2.4 m) straight = 8.0 ft (2.4 m)
Length of 7" (17.8 cm) system = 13.0 ft (3.9 m)
3¹⁄4" x 10" (8.3 cm x 25.4 cm) Vent System
Vent Piece
3¹⁄4" x 10" (8.3 cm x 25.4 cm)
90° elbow 5.0 ft (1.5 m)
3¹⁄4" x 10" (8.3 cm x 25.4 cm)
flat elbow 12.0 ft (3.7 m)
3¹⁄4" x 10" (8.3 cm x 25.4 cm)
wall cap 0.0 ft (0.0 m)
Example vent system
Maximum Recommended Length = 35 ft (10.7 m)
1 - 90° elbow = 5.0 ft (1.5 m)
8 ft (2.4 m) straight = 8.0 ft (2.4 m)
1 - wall cap = 0.0 ft (0.0 m)
Length of 3¹⁄4" x 10" (8.3 cm x 25.4 cm)
system = 13.0 ft (3.9 m)
Electrical Requirements
Observe all governing codes and ordinances.
Ensure that the electrical installation is adequate and in
conformance with National Electrical Code, ANSI/NFPA 70
(latest edition), or CSA Standards C22.1-94, Canadian Electrical
Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local
codes and ordinances.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
W
all cap
7" (17.8 cm) round
90˚ elbow
2 ft (0.6 m)
6 ft (1.8 m)
Wall cap
3
¼
" x 10"
(8.3 x 25.4 cm)
elbow
2 ft
(0.6 m)
6 ft (1.8 m)

8
■A 120-volt, 60 Hz., AC-only, 15-amp, fused electrical circuit
is required.
■If the house has aluminum wiring, follow the procedure
below:
1. Connect a section of solid copper wire to the pigtail
leads.
2. Connect the aluminum wiring to the added section
of copper wire using special connectors and/or tools
designed and UL Listed for joining copper to aluminum.
Follow the electrical connector manufacturer’s recommended
procedure. Aluminum/copper connection must conform with
local codes and industry accepted wiring practices.
■Wire sizes and connections must conform with the rating of
the appliance as specified on the model/serial/rating plate.
The model/serial/rating plate is located inside the range hood
on the left wall.
■Wire sizes must conform to the requirements of the National
Electrical Code, ANSI/NFPA 70 (latest edition), or CSA
Standards C22. 1-94, Canadian Electrical Code, Part 1 and
C22.2 No. 0-M91 (latest edition) and all local codes and
ordinances.
INSTALLATION INSTRUCTIONS
Prepare Location
NOTE: It is recommended that the vent system be installed
before hood is installed.
Before making cutouts, make sure there is proper clearance
within the ceiling or wall for exhaust vent.
1. Disconnect "wer.
2. Depending on your model, determine which venting method
to use: roof, wall, or non-vented (recirculating).
3. Select a flat surface for assembling the range hood. Place
covering over that surface.
4. Lift the range hood and set it upside down onto covered
surface.
Determine Wiring Hole Location
Cut only one 1¹⁄4" (3.2 cm) diameter wiring access hole.
1. Determine and clearly mark a vertical centerline on the wall
and cabinet in the area the vent opening will be made.
A. Centerline
To wire through top:
1. Mark a line distance “A” from the right of the centerline
on the underside of the cabinet. For 12" (30.5 cm) deep
cabinets, mark the "int on this line that is 2" (5.1 cm) from the
back wall. For 15" (38.1 cm) deep cabinets, mark the point
on this line that is 5" (12.7 cm) from the back wall. Drill a 1¼"
(3.2 cm) diameter hole through the cabinet at this "int.
To wire through wall:
1. Mark a line distance “A” from the right of the centerline on
the underside of the wall. Mark the point on this line that is
7⁄8" (2.2 cm) from the underside of the cabinet. Drill a 1¹⁄4"
(3.2 cm) diameter hole through the rear wall at this "int.
A. 8³⁄8" (21.3 cm)
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
A
A
Centerline
⁷⁄₈" (2.2 cm
)
Centerline
AB
A. 8³⁄8" (21.3 cm)
B. 2" (5.1 cm) for 12" (30.5 cm) deep cabinets*
5" (12.7 cm) for 15" (38.1 cm) deep cabinets*
*From wall, not cabinet frame

9
Style 1 - Cut Openings for 3¼" x 10"
(8.3 cm x 25.4 cm) Rectangular Vent System
Roof Venting
To make a 4¹⁄4" x 10½" (10.8 cm x 26.7 cm) rectangular
cutout on the underside of cabinet top and bottom:
1. Mark lines ¹⁄2" (1.3 cm) and 4³⁄4" (12.1 cm) from the back wall
on the centerline of the underside of cabinet.
2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline
on the underside of cabinet.
3. Use saber or keyhole saw to cut a rectangular opening for
vent.
4. Repeat steps 1-3 for the underside of the top of the cabinet.
Wall Venting
To make a 3½" x 10½" (8.9 cm x 26.7 cm) rectangle in the
wall:
1. Make 2 lines by measuring ³⁄8" (0.9 cm) and 37⁄8" (9.8 cm)
down from underside of cabinet and mark on the centerline
on the back wall.
2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline
on the wall.
3. Use saber or keyhole saw to cut a rectangular opening in the
wall for the vent.
Style 2 - Cut Openings for 3¼" x 10" (8.3 x 25.4 cm)
Rectangular Vent to Round Vent Transition
Roof Venting
To make a 4¹⁄4" x 10½" (10.8 cm x 26.7 cm) rectangular
cutout on the underside of cabinet bottom:
1. Mark lines ¹⁄2" (1.3 cm) and 4³⁄4" (12.1 cm) from the back wall
on the centerline of the underside of cabinet.
2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline
on the underside of cabinet.
3. Use saber or keyhole saw to cut a rectangular opening for
vent.
To make a circular vent opening on the underside of the
cabinet top:
1. Mark a centerline on the underside of the top of cabinet.
2. Mark a line 5" (12.7 cm) from the back wall on the underside
of the top of cabinet.
3. Use a compass or a circle template to draw a circle with a
diameter that is ¼" (0.64 cm) larger than the vent.
4. Use saber or keyhole saw to cut the circular vent opening.
Style 3 - Cut Openings for 7" (17.8 cm) Round Vent
To make a circular vent openings on the underside of the
cabinet top and bottom:
1. Mark a centerline on the underside of the top of cabinet.
2. Mark a line 5" (12.7 cm) from the back wall on the underside
of the top and bottom of cabinet.
3. Use a compass or a circle template to draw a circle with a
diameter that is ¼" (0.64 cm) larger than the vent.
4. Use saber or keyhole saw to cut the circular vent opening.
⅜"
3⅞"
Cabinet
front
(0.9 cm)
(9.8 cm)
5¼"
(13.3 cm)
Centerline
5¼"
(13.3 cm)
B
*From wall, not cabinet frame
A
A. 1/2" (1.3 cm)*
B. 43/4" (12.1 cm)*
*From wall, not cabinet frame
Cabinet cutouts
A
B
A. 1/2" (1.3 cm)*
B. 43/4" (12.1 cm)*
*From wall, not
cabinet frame
A
A. 5" (12.7 cm)*
Circular vent opening
Cabinet
cutouts
*From wall, not
cabinet frame
A
A. 5" (12.7 cm)*

10
Install Vent System
1. Install vent through the vent opening in upper cabinet or wall.
Complete venting system according to the selected venting
method. See the “Venting Requirements” section.
2. Use caulking to seal exterior wall or roof opening around
the cap.
Prepare Range Hood
Only for venting through the top/wall options:
1. Remove vent knockouts, depending on your installation
requirements.
A. Round vent knockout
B. Top rectangular vent knockout
C. Rear rectangular vent knockout
Round vent system installations - Remove top rectangular and
round vent knockouts.
Rectangular vent system installations - For roof installations,
remove the top rectangular vent knockout. For wall installations,
remove the rear rectangular vent knockout.
Non-vent (recirculating) installations - Do not remove any
knockouts.
2. Install 7" (17.8 cm) round vent mounting plate or 3¹⁄4" x 10"
(8.3 cm x 25.4 cm) vent damper, depending on your vent
system installation. Attach to range hood with 3.5 x 9.5 mm
screws provided and remove the tape from the damper flap.
NOTE: An optional 7" (17.8 cm) round damper is also
available as an accessory. For information on ordering,
see the “Accessories” section.
A. 7" (17.8 cm) round damper
(See the “Accessories” section)
B. 3.5 x 9.5 mm screws
C. 7" (17.8 cm) round vent mounting plate
D. Round vent knockout
E. Rectangular vent knockout
NOTE: The round vent damper may only be installed on the top
of the product.
A. Vertical air transition
B. 3.5 x 9.5 mm screws
C. Vent knockouts
D. Horizontal air transition
Only for recirculating options
For this venting method, it is neccesary to purchase a Charcoal
Filter Kit. See the “Accessories” section for ordering.
1. Remove each filter by pulling the spring-release handle and
then pulling down the filter.
2. Remove the venting method screw from the Vented option
with a T10 TORX®screwdriver and set aside.
A. Venting method screw
A
B
C
A
B
C
B
D
A
A
B
C
D
E