Omegalink 553 User manual

5-BUTTON LCD 2-WAY
QUICK START OPERATION GUIDE
5-BUTTON LCD 2-WAY
QUICK START OPERATION GUIDE
REPLACING YOUR REMOTE BATTERY
STEPS REMOTE PART# BATTERY (QTY)
1) (551 only) Find the part # on the back of the remote to identify the battery.
2) (551 only) Locate the relief in case near the key chain and separate the case
halves to access & replace the batteries.
553 Rechargable
551 CR2032
SECURITY, KEYLESS ENTRY, & CONVENIENCE FUNCTIONS
FUNCTION BUTTON(S) REMOTE CONFIRMATION NOTE
Lock & Arm* “Lock” or ”arm” Displays The doors will lock.
Unlock & Disarm* “Unlock” or ”D_Arm”
Displays The doors will unlock.
Silent Lock* x 1 Beep The doors will lock with no audible confirmation.
Silent Unlock* x 2 Beep Perform within 1 second. The doors will unlock with no
audible confirmation.
Trunk/Hatch Release for 3 sec. “TRUNK OPEN” Displays By default, the system will also disarm/unlock.
Panic* or for 3 sec. “PANIC” Displays The system will sound the horn/siren for Panic Mode.
Register today at www.CarAlarm.com
For warranty info & Download the latest operation guide.
Copyright 2019 Omega Research & Development Technologies, Inc. OC_55308_20190712
/c/omegard
/omegard
Problems? Questions? Contact Customer Service:
800-554-4053 (toll free) | [phone] (outside USA)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna., Increase the separation
between the equipment and receiver., Connect the equipment into an outlet on a circuit different from that to which the receiver is connected., Consult the dealer or an experienced radio/TV technician for help.,
Warning! Changes or modifi cations made to this equipment not expressly approved by the part responsible for compliance could void the use’s authority to operate the equipment
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifi cations to this equipment. Such modifi cations could void the user’s authority to operate the equipment.
14
PROGRAMMING REMOTES TO THE SYSTEM
Remote programming is dependant on the system being controlled. Please consult your dealer or the system guide for the proper
programming instructions.
Visit www.CarAlarm.com today
To Download the latest operation guide and learn more about system upgrades & other features!
OMPATIB
Scan to register
& download the
latest operation
guide at
CarAlarm.com!

5-BUTTON LCD 2-WAY
QUICK START OPERATION GUIDE
5-BUTTON LCD 2-WAY
QUICK START OPERATION GUIDE
2
REMOTE START FUNCTIONS
FUNCTION BUTTON(S) LCD CONFIRMATION NOTE
Engine Start/Stop x 2 “START” + Melody Upon successful remote start the clock will display the remaining engine run time (M:SS).
Take Over: Turn ignition key ‘ON’, press brake pedal.
Run Time Extender* Chirp + “START ON” Clock will restart the run timer (only allowed once per remote start cycle).
Auto Start Mode* & “TEMP START ON” or
“TEMP START OFF”
Remote starts your vehicle every 2, 3, or 4 hours (programmable) or upon temperature threshold (set in the remote
start unit).
WINDOW-MOUNT ANTENNA/RECEIVER
OTHER CONTROLLER FUNCTIONS
FUNCTION BUTTON(S) LCD
CONFIRMATION NOTE
Remote Valet* Hold &
for 3 sec
Beep + Screen flashes
This disables remote start and the security
system. The status LED will turn on. Repeat
this process or press valet button once to exit
valet mode.
Multi-Car Hold & for
3 sec
Beep + ”Shift” icon The “Shift” icon appear when in car 2 opera-
tion. Repeat to return to car 1 operation.
Button Lock Hold &
for 3 sec
Beep + Screen flashes
When button lock is on the remote will not
transmit. When any button is pressed the
screen will flash 5x. Repeat to unlock.
Status Update* Hold &
for 3 sec
Beep + Icons change
(if status has changed)
The screen icons will update to the current
status of the system.
, “AUX 1”AUX1 - Write function in “FUNCTION” column
x 2 , “AUX 2”AUX2 - Write function in “FUNCTION” column
x 3 , “AUX 3”AUX3 - Write function in “FUNCTION” column
& “AUX 4”AUX4 - Write function in “FUNCTION” column
Power ON Hold for 3 sec. The screen will
turn on The remote will resume all normal functions.
Power OFF Hold for 5 sec. The screen will
turn off The remote will not function until powered on.
2WAY OPTIONS
OPTIONS PROCEDURE
Set Clock (H:M)
Hold for 5 seconds. The controller will beep
indicating it has entered option programming.
Tap to scroll through each option.
Press or to scroll through each option
setting.
Hold for 3 seconds or no activity for 15 seconds
to exit option programming
Set Alarm Clock (H:M)
Change Alarm Melody
Alarm Clock On/Off
Set Timer (H:M)
Set Timer Melody
Timer On/Off
Change Start/Stop Melody
12/24 Hour Clock
OTHER FEATURES BUTTON(S) LCD CONFIRMATION
Alarm Clock On/Off & . Melody + “Clock” icon
Silent Mode On/Off & Beep OR “Vibrate” icon.
Parking Timer Hold
& press .
Pressing will scroll thru
the timer length options.
3
*All functions are dependent upon vehicle & system availability. Consult your
installer to confi rm feature availability.
*All functions are dependent upon vehicle & system availability. Consult your installer to confi rm feature availability.
Status LED
Valet / Programming Button
Status LED