Omnia 11 Instruction Manual
NETWORK CONFIGURATION (CONT.) sysTEm CONFIGURATION sysTEm CONFIGURATION (CONT.) QUICK-sTART INsTAllATION GUIdE
OmNIA.11 sTEREO Fm AUdIO PROCEssOR
Items you need to supply:
• RackwithfouravailableEIArackspacesformounting
• Professionalline-levelanalogorAES/EBUdigitalaudio
sourcesonstandardXLRconnectors
• ConfiguredEthernetswitch
REQUIRED EQUIPMENT, CABLES, AND ACCESSORIES:
Thereareafewadditionalitemsrequiredforasuccessfulinstallation.Checkthelistbelowandmakesure
youhavewhatyouneed.
Included items:
• Omnia.11AudioProcessor
• ACPowercable
• Ethernetcable
• 4rackscrews
WehavemadethisOmniaSystemeasytosetupandconfigure.Thisquick-startguidewilltakeyouthroughthe
basicstepstoconfigureyournewOmnia.11tostartdeliveringcleaner,clearer,louder,andmoreconsistentsound.
Beforewegetstarted,let’smakesureyouhavewhatyouneed.
ThANK yOU FOR PURChAsING ThE OmNIA.11 sTEREO Fm
AUdIO PROCEssOR
CONTINUE TO sysTEm CONFIGURATION
Network configuration is complete. Your system is
readyforsystemconfiguration.Continuetothe“System
Configuration”instructions.
1. Once the system has rebooted, touch the “Setup”
button(S).
2. Touch the Livewire button (T). The Livewire
configurationscreenwillbedisplayed(U).
3. If you do not have a Livewire system, make sure
the 2 Livewire output channels are disabled. The
2 "Enable" buttons (V) will be white if Livewire
is disabled and green when enabled. To disable
Livewire, touch each of the two green "Enable"
buttons(V)toturnthemwhite.
4. If you do have a Livewire system, enable Livewire
bytouchingeachofthetwo"Enable"buttons(V)to
turnthemgreen.
5. IfyouhaveaLivewiresystem,touchthewhitefields
(W) next to the Output #1 and #2 and enter the
appropriatechannelvalueviathepop-upkeyboard(X).
6. Touchthe“APPLY”button(Y)undertheOutputs.
7. Touchthewhitefields(Z)nexttotheInput#1and#2
toentertheappropriatechannelvalueviathepop-
upkeyboard(X).
8. Touchthe“APPLY”buttonundertheInputs(AA).
lIVEWIRE CONFIGURATION
OUTPUT CONFIGURATION
1. Touchthe“Output”icon(II).TheOutputConfigurationscreenwillbedisplayed.Ifthe“Basic”tabisnot
active,touchtoselectit.
INPUT CONFIGURATION
1. Touchthe“ADJ”icon(BB)toreturntotheinitialSystemscreen.
2. Touchthe“Input”icon(CC).TheInputConfigurationscreenwillbedisplayed.Ifthe“Basic”tab(DD)
isnotactive,touchtoselectit.
3. Fromthe“InputSource”drop-down(EE),selecttheAnalog,AES/EBUorLivewireinputasappropriate
foryourinstallation.Ifyouraudiosourceisprovidinganaudiofeedyoushouldseemeteractivityon
thebargraphmeters(FF).
4. Whiledrivingtheinputswithtypicalprogrammaterialatnormaloperatinglevel,adjustthe
appropriate“Master”InputGaincontrol(GG)foryourinstallationuntilthepeak-readinginputbar
graphmetersarereadingjust“intotheyellow”(about–15to–12dBFSorso).Iftheleft/rightaudio
levelscomingintotheOmnia.11aresomewhatunbalanced,youcanadjustthe“RightTrim”control
(HH)tochangetheleveloftherightchannelaloneoveralimitedrange.
©2016TLSCorp.,AllRightsReserved. 1490-00099-001—QUICKSTARTGUIDE:OMNIA.11C16/15035
yOUR sETUP Is COmPlETE!
That’sit!YouarenowreadytoexperiencetheOmnia.11
forsoundlikeneverbefore.
1. Touchthe“FMOptions”button(JJ)ontheleftsideofthe
MenuAreaandensurethatthePre-Emphasis,Diversity
Delay(if present)and BS-412 settingsarecorrectfor
yoursystemandyourlocation.
2. Touch the appropriate button (KK) above the “FM
Options”buttontoselectthegroupofoutputcontrols
fortheoutputyouwillbeusing.Alloutputsareactive
simultaneously. Note: If you are using a conventional
AES/EBU L/R digital output to feed an FM exciter or
linearSTL,touchthe“AES/EBU”buttonandbesurethe
“OutputSelection”issetto“FM”andthe“De-emphasis”
isturned“OFF”fortheoutputbeingused.Foraccessto
thecompositeMPXstereogeneratoroutputleveland
stereo pilot controls, touch the “Composite” button.
Note that these controls simultaneously adjust the
OmniaDirectoutput levelsas well. Finally,adjustthe
appropriatecontrolsothatthepeakoutput/modulation
level is correct for the equipment that follows the
Omnia.11.
3. Touchthe“FM”iconbutton(LL)atthetopofthescreen
andthentouchthe“Preset”tab(MM)todisplaythelist
offactoryprocessingpresets.Ifthepresetlistislocked
(grayed-out),touchthe“padlock”icontounlockit.Once
unlocked,simplytouchthedesiredpresetnameinthe
listanditwillbeputdirectly“ontheair".Werecommend
listening to all factory presets to get a feel for their
differencesandthenselectonetostartwith.
4. Touch the “Quick Setup” tab (NN) and adjust the
followingcontrolstosetthebasicloudness,bassand
brightnesssounddesired.
5. Adjust the “Clipper Drive” control (OO) as low as
possible for the loudness needed. This controls the
primaryloudnessvs.distortiontradeoff.Turningitup
makes the sound louder (but more distorted) while
turning it down makes the sound cleaner but not as
loud.Itshouldalwaysbesetaslowaspossibleforthe
levelofloudnessrequired.
6. Settheoverallamountofbassusingthe“Bass”control
(PP). At higher settings of the “Bass Thump” (QQ)
control,the “kick” or “Thump”action ofbass material
isemphasized.
7. Set the basic brightness of a preset by using the
“Presence” (RR), “Treble” (SS) and “Sparkle” (TT)
controls.Notethatthesethreecontrolsonlyboostthe
brightness.Asettingof“0.0”is“flat”ortheminimum
amount of boost for the particular preset that is
currently selected. Reducing brightness can be done,
forone example, by reducingthehigher bands of the
AGCorLimitermixers.
T
S
U
Z
AA
VW
Y
X
II
KK
JJ
LL
MM
BB
CC
DD
GG
HH
EE
FF
NN
OO
PP
RR
QQ
SS TT
G
F
H
PhysICAl INsTAllATION
1. Locatethereleasepin(A)ontheinsidetopofeachhandleontheOmnia.11.
2. Slide and holdthereleasepins(A)outwardsandthenpullthehandles(B)towardsyouuntilyouhearaclick.
Makesureeachhandleissecurelylockedintotheforwardposition.
3. Usingthehandles(B), lift and slidetheOmnia.11intotheequipmentrackandsecurewithall4rackscrews.
4. Onceinstalledintotherack,locatethereleasepin(A)ontheinsidetopofeachhandle,slidethepintoward
youandfoldthehandles(B)backtotheirnormalposition.
AUdIO CONFIGURATION
AUdIO CONNECTIONs
1. Determinetheinputsandoutputsthatareappropriateforyourinstallationandfollowthe
appropriateinstructions.
AUDIO INPUT - Both analog and digital input sources may be connected simultaneously,
however, only the input source that has been selected in the Input menu will be active.
Input source selection will be covered later in this guide.
a. ForAnalogaudio,connectXLRaudiocablestotheleftandrightANALOGINPUTS(C)jacks.
b. ForDigitalaudio,connectXLRaudiocablestotheAESINPUT(D)jack.
c. ForanexistingLivewiresystem,thesingleLivewireEthernetconnectionisallthatisneededforaudioI/O
(exceptforthecompositeMPXoutputs).IMPORTANT: Do not connect an Ethernet cable at this time.
CONTINUE TO NETWORK CONFIGURATION
Youraudioconnectionsarecomplete.Continuetothe”NetworkConfiguration”instructions.
CONTINUE TO AUdIO CONFIGURATION
Yourphysicalinstallationiscomplete.Continuetothe”AudioConfiguration”instructions.
AUDIO OUTPUT - All outputs are active simultaneously.
a. ForAnalogaudio,connectXLRaudiocablestotheleftandrightANALOGOUTPUTSjacks(F).
b. ForDigitalaudio,connectXLRaudiocablestotheAESOUT1/2jacks(G).
c. ForadirectcompositeMPXconnection,connectanXLRcabletotheAESCOMPOSITEOUTjack(H).
Note:IfyouwillbeusingconventionalAES/EBUL/RdigitalaudiotofeedyourSTLorFMexciter,besure
anypre-emphasisandlimiters(ifpresent)arefullydefeatedintheexciter.TheOmniamustbetheonly
deviceprovidingthepre-emphasissoitsownde-emphasisontheAES/EBUoutputbeingusedmust
alsobe“Off”.AlsonotethatiftheSTLusesacodec(isnotlinear),theOmniamustbelocatedatthe
transmittersiteforbestperformanceandsoundquality.
d. ForanexistingLivewiresystem,thesingleLivewireEthernetconnectionisallthatisneededforaudioI/O
(exceptforthecompositeMPXoutputs).IMPORTANT: Do not connect an Ethernet cable at this time.
NETWORK CONFIGURATION
INsTAllATION hElP
Formore details aboutthe Omnia.11, orto download the fullmanual
pleasevisithttps://www.telosalliance.com/Omnia/Omnia11
Ifyouhavemorequestions,calltheTelosAlliance24/7SupportTeamat
+1 (216) 622-0247,oremailusatsupport@telosalliance.com,we’dbe
happytohelpyouout.
1. Touch the “Setup” button (L). The Network
configurationscreenwillbedisplayed(M).
2. Touchthewhitefield(N)totherightofIPAddress
labeltoenterastaticIPaddress.Note:TheOmnia.11
requires2freestaticIPaddressesonyournetwork
(DHCP is not supported), the one that you enter
andtheone directlyabovetheonethatyouenter.
For example, if you enter 192.168.0.125 as the IP
Address,bothitand192.168.0.126needtobeopen
onthenetwork.
3. Theon-screenkeyboardwillpop up (O).Touchthe
“0-9*/=” button to shift the keyboard to number
entrymode.
4. Touch the backspace key to delete the current
informationdigitbydigit,thenenteryourdesiredIP
addressfromthekeyboard.
5. TouchOK(Q)andthekeyboardwillnolongerdisplay.
6. IfyournetworkrequireschangestoSubnetMaskor
Gatewayvalues,touchthewhitefieldstotheright
ofthoselabelstochangethevaluesviathepop-up
keyboard.
7. Once your values have been entered, touch the
“APPLY” button (R). The system will display an
option to either "Reboot Now" or Reboot Later".
Touch“RebootNow”torebootthesystemandapply
thenewparameters.
NETWORK PARAmETER sETUP
2. MakesurethatnocablesarepluggedintoeitherEthernetport.
3. ConnecttheOmnia.11toACMains(I).
4. Oncethesystemhasbootedupcompletely,connectoneendoftheEthernetcabletothetopLivewire/100BT
port(J)onthebackoftheOmnia.11.ConnecttheotherendoftheEthernetcabletoaconfiguredEthernet
switch(K)toallowaccesstothenetwork.
RACK mOUNTING
AUdIO CONFIGURATION (CONT.)
A
A
A
A
B
B
D
C
L
M
N
R
O
P Q
G
F
H
PhysICAl INsTAllATION
1. Locatethereleasepin(A)ontheinsidetopofeachhandleontheOmnia.11.
2. Slide and holdthereleasepins(A)outwardsandthenpullthehandles(B)towardsyouuntilyouhearaclick.
Makesureeachhandleissecurelylockedintotheforwardposition.
3. Usingthehandles(B), lift and slidetheOmnia.11intotheequipmentrackandsecurewithall4rackscrews.
4. Onceinstalledintotherack,locatethereleasepin(A)ontheinsidetopofeachhandle,slidethepintoward
youandfoldthehandles(B)backtotheirnormalposition.
AUdIO CONFIGURATION
AUdIO CONNECTIONs
1. Determinetheinputsandoutputsthatareappropriateforyourinstallationandfollowthe
appropriateinstructions.
AUDIO INPUT - Both analog and digital input sources may be connected simultaneously,
however, only the input source that has been selected in the Input menu will be active.
Input source selection will be covered later in this guide.
a. ForAnalogaudio,connectXLRaudiocablestotheleftandrightANALOGINPUTS(C)jacks.
b. ForDigitalaudio,connectXLRaudiocablestotheAESINPUT(D)jack.
c. ForanexistingLivewiresystem,thesingleLivewireEthernetconnectionisallthatisneededforaudioI/O
(exceptforthecompositeMPXoutputs).IMPORTANT: Do not connect an Ethernet cable at this time.
CONTINUE TO NETWORK CONFIGURATION
Youraudioconnectionsarecomplete.Continuetothe”NetworkConfiguration”instructions.
CONTINUE TO AUdIO CONFIGURATION
Yourphysicalinstallationiscomplete.Continuetothe”AudioConfiguration”instructions.
AUDIO OUTPUT - All outputs are active simultaneously.
a. ForAnalogaudio,connectXLRaudiocablestotheleftandrightANALOGOUTPUTSjacks(F).
b. ForDigitalaudio,connectXLRaudiocablestotheAESOUT1/2jacks(G).
c. ForadirectcompositeMPXconnection,connectanXLRcabletotheAESCOMPOSITEOUTjack(H).
Note:IfyouwillbeusingconventionalAES/EBUL/RdigitalaudiotofeedyourSTLorFMexciter,besure
anypre-emphasisandlimiters(ifpresent)arefullydefeatedintheexciter.TheOmniamustbetheonly
deviceprovidingthepre-emphasissoitsownde-emphasisontheAES/EBUoutputbeingusedmust
alsobe“Off”.AlsonotethatiftheSTLusesacodec(isnotlinear),theOmniamustbelocatedatthe
transmittersiteforbestperformanceandsoundquality.
d. ForanexistingLivewiresystem,thesingleLivewireEthernetconnectionisallthatisneededforaudioI/O
(exceptforthecompositeMPXoutputs).IMPORTANT: Do not connect an Ethernet cable at this time.
NETWORK CONFIGURATION
INsTAllATION hElP
Formore details aboutthe Omnia.11, orto download the fullmanual
pleasevisithttps://www.telosalliance.com/Omnia/Omnia11
Ifyouhavemorequestions,calltheTelosAlliance24/7SupportTeamat
happytohelpyouout.
1. Touch the “Setup” button (L). The Network
configurationscreenwillbedisplayed(M).
2. Touchthewhitefield(N)totherightofIPAddress
labeltoenterastaticIPaddress.Note:TheOmnia.11
requires2freestaticIPaddressesonyournetwork
(DHCP is not supported), the one that you enter
andtheone directlyabovetheonethatyouenter.
For example, if you enter 192.168.0.125 as the IP
Address,bothitand192.168.0.126needtobeopen
onthenetwork.
3. Theon-screenkeyboardwillpop up (O).Touchthe
“0-9*/=” button to shift the keyboard to number
entrymode.
4. Touch the backspace key to delete the current
informationdigitbydigit,thenenteryourdesiredIP
addressfromthekeyboard.
5. TouchOK(Q)andthekeyboardwillnolongerdisplay.
6. IfyournetworkrequireschangestoSubnetMaskor
Gatewayvalues,touchthewhitefieldstotheright
ofthoselabelstochangethevaluesviathepop-up
keyboard.
7. Once your values have been entered, touch the
“APPLY” button (R). The system will display an
option to either "Reboot Now" or Reboot Later".
Touch“RebootNow”torebootthesystemandapply
thenewparameters.
NETWORK PARAmETER sETUP
2. MakesurethatnocablesarepluggedintoeitherEthernetport.
3. ConnecttheOmnia.11toACMains(I).
4. Oncethesystemhasbootedupcompletely,connectoneendoftheEthernetcabletothetopLivewire/100BT
port(J)onthebackoftheOmnia.11.ConnecttheotherendoftheEthernetcabletoaconfiguredEthernet
switch(K)toallowaccesstothenetwork.
RACK mOUNTING
AUdIO CONFIGURATION (CONT.)
A
A
A
A
B
B
D
C
L
M
N
R
O
P Q
G
F
H
PhysICAl INsTAllATION
1. Locatethereleasepin(A)ontheinsidetopofeachhandleontheOmnia.11.
2. Slide and holdthereleasepins(A)outwardsandthenpullthehandles(B)towardsyouuntilyouhearaclick.
Makesureeachhandleissecurelylockedintotheforwardposition.
3. Usingthehandles(B), lift and slidetheOmnia.11intotheequipmentrackandsecurewithall4rackscrews.
4. Onceinstalledintotherack,locatethereleasepin(A)ontheinsidetopofeachhandle,slidethepintoward
youandfoldthehandles(B)backtotheirnormalposition.
AUdIO CONFIGURATION
AUdIO CONNECTIONs
1. Determinetheinputsandoutputsthatareappropriateforyourinstallationandfollowthe
appropriateinstructions.
AUDIO INPUT - Both analog and digital input sources may be connected simultaneously,
however, only the input source that has been selected in the Input menu will be active.
Input source selection will be covered later in this guide.
a. ForAnalogaudio,connectXLRaudiocablestotheleftandrightANALOGINPUTS(C)jacks.
b. ForDigitalaudio,connectXLRaudiocablestotheAESINPUT(D)jack.
c. ForanexistingLivewiresystem,thesingleLivewireEthernetconnectionisallthatisneededforaudioI/O
(exceptforthecompositeMPXoutputs).IMPORTANT: Do not connect an Ethernet cable at this time.
CONTINUE TO NETWORK CONFIGURATION
Youraudioconnectionsarecomplete.Continuetothe”NetworkConfiguration”instructions.
CONTINUE TO AUdIO CONFIGURATION
Yourphysicalinstallationiscomplete.Continuetothe”AudioConfiguration”instructions.
AUDIO OUTPUT - All outputs are active simultaneously.
a. ForAnalogaudio,connectXLRaudiocablestotheleftandrightANALOGOUTPUTSjacks(F).
b. ForDigitalaudio,connectXLRaudiocablestotheAESOUT1/2jacks(G).
c. ForadirectcompositeMPXconnection,connectanXLRcabletotheAESCOMPOSITEOUTjack(H).
Note:IfyouwillbeusingconventionalAES/EBUL/RdigitalaudiotofeedyourSTLorFMexciter,besure
anypre-emphasisandlimiters(ifpresent)arefullydefeatedintheexciter.TheOmniamustbetheonly
deviceprovidingthepre-emphasissoitsownde-emphasisontheAES/EBUoutputbeingusedmust
alsobe“Off”.AlsonotethatiftheSTLusesacodec(isnotlinear),theOmniamustbelocatedatthe
transmittersiteforbestperformanceandsoundquality.
d. ForanexistingLivewiresystem,thesingleLivewireEthernetconnectionisallthatisneededforaudioI/O
(exceptforthecompositeMPXoutputs).IMPORTANT: Do not connect an Ethernet cable at this time.
NETWORK CONFIGURATION
INsTAllATION hElP
Formore details aboutthe Omnia.11, orto download the fullmanual
pleasevisithttps://www.telosalliance.com/Omnia/Omnia11
Ifyouhavemorequestions,calltheTelosAlliance24/7SupportTeamat
+1 (216) 622-0247,oremailusatsupport@telosalliance.com,we’dbe
happytohelpyouout.
1. Touch the “Setup” button (L). The Network
configurationscreenwillbedisplayed(M).
2. Touchthewhitefield(N)totherightofIPAddress
labeltoenterastaticIPaddress.Note:TheOmnia.11
requires2freestaticIPaddressesonyournetwork
(DHCP is not supported), the one that you enter
andtheone directlyabovetheonethatyouenter.
For example, if you enter 192.168.0.125 as the IP
Address,bothitand192.168.0.126needtobeopen
onthenetwork.
3. Theon-screenkeyboardwillpop up (O).Touchthe
“0-9*/=” button to shift the keyboard to number
entrymode.
4. Touch the backspace key to delete the current
informationdigitbydigit,thenenteryourdesiredIP
addressfromthekeyboard.
5. TouchOK(Q)andthekeyboardwillnolongerdisplay.
6. IfyournetworkrequireschangestoSubnetMaskor
Gatewayvalues,touchthewhitefieldstotheright
ofthoselabelstochangethevaluesviathepop-up
keyboard.
7. Once your values have been entered, touch the
“APPLY” button (R). The system will display an
option to either "Reboot Now" or Reboot Later".
Touch“RebootNow”torebootthesystemandapply
thenewparameters.
NETWORK PARAmETER sETUP
2. MakesurethatnocablesarepluggedintoeitherEthernetport.
3. ConnecttheOmnia.11toACMains(I).
4. Oncethesystemhasbootedupcompletely,connectoneendoftheEthernetcabletothetopLivewire/100BT
port(J)onthebackoftheOmnia.11.ConnecttheotherendoftheEthernetcabletoaconfiguredEthernet
switch(K)toallowaccesstothenetwork.
RACK mOUNTING
AUdIO CONFIGURATION (CONT.)
A
A
A
A
B
B
D
C
L
M
N
R
O
P Q
G
F
H
PhysICAl INsTAllATION
1. Locatethereleasepin(A)ontheinsidetopofeachhandleontheOmnia.11.
2. Slide and holdthereleasepins(A)outwardsandthenpullthehandles(B)towardsyouuntilyouhearaclick.
Makesureeachhandleissecurelylockedintotheforwardposition.
3. Usingthehandles(B), lift and slidetheOmnia.11intotheequipmentrackandsecurewithall4rackscrews.
4. Onceinstalledintotherack,locatethereleasepin(A)ontheinsidetopofeachhandle,slidethepintoward
youandfoldthehandles(B)backtotheirnormalposition.
AUdIO CONFIGURATION
AUdIO CONNECTIONs
1. Determinetheinputsandoutputsthatareappropriateforyourinstallationandfollowthe
appropriateinstructions.
AUDIO INPUT - Both analog and digital input sources may be connected simultaneously,
however, only the input source that has been selected in the Input menu will be active.
Input source selection will be covered later in this guide.
a. ForAnalogaudio,connectXLRaudiocablestotheleftandrightANALOGINPUTS(C)jacks.
b. ForDigitalaudio,connectXLRaudiocablestotheAESINPUT(D)jack.
c. ForanexistingLivewiresystem,thesingleLivewireEthernetconnectionisallthatisneededforaudioI/O
(exceptforthecompositeMPXoutputs).IMPORTANT: Do not connect an Ethernet cable at this time.
CONTINUE TO NETWORK CONFIGURATION
Youraudioconnectionsarecomplete.Continuetothe”NetworkConfiguration”instructions.
CONTINUE TO AUdIO CONFIGURATION
Yourphysicalinstallationiscomplete.Continuetothe”AudioConfiguration”instructions.
AUDIO OUTPUT - All outputs are active simultaneously.
a. ForAnalogaudio,connectXLRaudiocablestotheleftandrightANALOGOUTPUTSjacks(F).
b. ForDigitalaudio,connectXLRaudiocablestotheAESOUT1/2jacks(G).
c. ForadirectcompositeMPXconnection,connectanXLRcabletotheAESCOMPOSITEOUTjack(H).
Note:IfyouwillbeusingconventionalAES/EBUL/RdigitalaudiotofeedyourSTLorFMexciter,besure
anypre-emphasisandlimiters(ifpresent)arefullydefeatedintheexciter.TheOmniamustbetheonly
deviceprovidingthepre-emphasissoitsownde-emphasisontheAES/EBUoutputbeingusedmust
alsobe“Off”.AlsonotethatiftheSTLusesacodec(isnotlinear),theOmniamustbelocatedatthe
transmittersiteforbestperformanceandsoundquality.
d. ForanexistingLivewiresystem,thesingleLivewireEthernetconnectionisallthatisneededforaudioI/O
(exceptforthecompositeMPXoutputs).IMPORTANT: Do not connect an Ethernet cable at this time.
NETWORK CONFIGURATION
INsTAllATION hElP
Formore details aboutthe Omnia.11, orto download the fullmanual
pleasevisithttps://www.telosalliance.com/Omnia/Omnia11
Ifyouhavemorequestions,calltheTelosAlliance24/7SupportTeamat
+1 (216) 622-0247,oremailusatsupport@telosalliance.com,we’dbe
happytohelpyouout.
1. Touch the “Setup” button (L). The Network
configurationscreenwillbedisplayed(M).
2. Touchthewhitefield(N)totherightofIPAddress
labeltoenterastaticIPaddress.Note:TheOmnia.11
requires2freestaticIPaddressesonyournetwork
(DHCP is not supported), the one that you enter
andtheone directlyabovetheonethatyouenter.
For example, if you enter 192.168.0.125 as the IP
Address,bothitand192.168.0.126needtobeopen
onthenetwork.
3. Theon-screenkeyboardwillpop up (O).Touchthe
“0-9*/=” button to shift the keyboard to number
entrymode.
4. Touch the backspace key to delete the current
informationdigitbydigit,thenenteryourdesiredIP
addressfromthekeyboard.
5. TouchOK(Q)andthekeyboardwillnolongerdisplay.
6. IfyournetworkrequireschangestoSubnetMaskor
Gatewayvalues,touchthewhitefieldstotheright
ofthoselabelstochangethevaluesviathepop-up
keyboard.
7. Once your values have been entered, touch the
“APPLY” button (R). The system will display an
option to either "Reboot Now" or Reboot Later".
Touch“RebootNow”torebootthesystemandapply
thenewparameters.
NETWORK PARAmETER sETUP
2. MakesurethatnocablesarepluggedintoeitherEthernetport.
3. ConnecttheOmnia.11toACMains(I).
4. Oncethesystemhasbootedupcompletely,connectoneendoftheEthernetcabletothetopLivewire/100BT
port(J)onthebackoftheOmnia.11.ConnecttheotherendoftheEthernetcabletoaconfiguredEthernet
switch(K)toallowaccesstothenetwork.
RACK mOUNTING
AUdIO CONFIGURATION (CONT.)
A
A
A
A
B
B
D
C
L
M
N
R
O
P Q
NETWORK CONFIGURATION (CONT.) sysTEm CONFIGURATION sysTEm CONFIGURATION (CONT.) QUICK-sTART INsTAllATION GUIdE
OmNIA.11 sTEREO Fm AUdIO PROCEssOR
Items you need to supply:
• RackwithfouravailableEIArackspacesformounting
• Professionalline-levelanalogorAES/EBUdigitalaudio
sourcesonstandardXLRconnectors
• ConfiguredEthernetswitch
REQUIRED EQUIPMENT, CABLES, AND ACCESSORIES:
Thereareafewadditionalitemsrequiredforasuccessfulinstallation.Checkthelistbelowandmakesure
youhavewhatyouneed.
Included items:
• Omnia.11AudioProcessor
• ACPowercable
• Ethernetcable
• 4rackscrews
WehavemadethisOmniaSystemeasytosetupandconfigure.Thisquick-startguidewilltakeyouthroughthe
basicstepstoconfigureyournewOmnia.11tostartdeliveringcleaner,clearer,louder,andmoreconsistentsound.
Beforewegetstarted,let’smakesureyouhavewhatyouneed.
ThANK yOU FOR PURChAsING ThE OmNIA.11 sTEREO Fm
AUdIO PROCEssOR
CONTINUE TO sysTEm CONFIGURATION
Network configuration is complete. Your system is
readyforsystemconfiguration.Continuetothe“System
Configuration”instructions.
1. Once the system has rebooted, touch the “Setup”
button(S).
2. Touch the Livewire button (T). The Livewire
configurationscreenwillbedisplayed(U).
3. If you do not have a Livewire system, make sure
the 2 Livewire output channels are disabled. The
2 "Enable" buttons (V) will be white if Livewire
is disabled and green when enabled. To disable
Livewire, touch each of the two green "Enable"
buttons(V)toturnthemwhite.
4. If you do have a Livewire system, enable Livewire
bytouchingeachofthetwo"Enable"buttons(V)to
turnthemgreen.
5. IfyouhaveaLivewiresystem,touchthewhitefields
(W) next to the Output #1 and #2 and enter the
appropriatechannelvalueviathepop-upkeyboard(X).
6. Touchthe“APPLY”button(Y)undertheOutputs.
7. Touchthewhitefields(Z)nexttotheInput#1and#2
toentertheappropriatechannelvalueviathepop-
upkeyboard(X).
8. Touchthe“APPLY”buttonundertheInputs(AA).
lIVEWIRE CONFIGURATION
OUTPUT CONFIGURATION
1. Touchthe“Output”icon(II).TheOutputConfigurationscreenwillbedisplayed.Ifthe“Basic”tabisnot
active,touchtoselectit.
INPUT CONFIGURATION
1. Touchthe“ADJ”icon(BB)toreturntotheinitialSystemscreen.
2. Touchthe“Input”icon(CC).TheInputConfigurationscreenwillbedisplayed.Ifthe“Basic”tab(DD)
isnotactive,touchtoselectit.
3. Fromthe“InputSource”drop-down(EE),selecttheAnalog,AES/EBUorLivewireinputasappropriate
foryourinstallation.Ifyouraudiosourceisprovidinganaudiofeedyoushouldseemeteractivityon
thebargraphmeters(FF).
4. Whiledrivingtheinputswithtypicalprogrammaterialatnormaloperatinglevel,adjustthe
appropriate“Master”InputGaincontrol(GG)foryourinstallationuntilthepeak-readinginputbar
graphmetersarereadingjust“intotheyellow”(about–15to–12dBFSorso).Iftheleft/rightaudio
levelscomingintotheOmnia.11aresomewhatunbalanced,youcanadjustthe“RightTrim”control
(HH)tochangetheleveloftherightchannelaloneoveralimitedrange.
©2016TLSCorp.,AllRightsReserved. 1490-00099-001—QUICKSTARTGUIDE:OMNIA.11C16/15035
yOUR sETUP Is COmPlETE!
That’sit!YouarenowreadytoexperiencetheOmnia.11
forsoundlikeneverbefore.
1. Touchthe“FMOptions”button(JJ)ontheleftsideofthe
MenuAreaandensurethatthePre-Emphasis,Diversity
Delay(if present)and BS-412 settingsarecorrectfor
yoursystemandyourlocation.
2. Touch the appropriate button (KK) above the “FM
Options”buttontoselectthegroupofoutputcontrols
fortheoutputyouwillbeusing.Alloutputsareactive
simultaneously. Note: If you are using a conventional
AES/EBU L/R digital output to feed an FM exciter or
linearSTL,touchthe“AES/EBU”buttonandbesurethe
“OutputSelection”issetto“FM”andthe“De-emphasis”
isturned“OFF”fortheoutputbeingused.Foraccessto
thecompositeMPXstereogeneratoroutputleveland
stereo pilot controls, touch the “Composite” button.
Note that these controls simultaneously adjust the
OmniaDirectoutput levelsas well. Finally,adjustthe
appropriatecontrolsothatthepeakoutput/modulation
level is correct for the equipment that follows the
Omnia.11.
3. Touchthe“FM”iconbutton(LL)atthetopofthescreen
andthentouchthe“Preset”tab(MM)todisplaythelist
offactoryprocessingpresets.Ifthepresetlistislocked
(grayed-out),touchthe“padlock”icontounlockit.Once
unlocked,simplytouchthedesiredpresetnameinthe
listanditwillbeputdirectly“ontheair".Werecommend
listening to all factory presets to get a feel for their
differencesandthenselectonetostartwith.
4. Touch the “Quick Setup” tab (NN) and adjust the
followingcontrolstosetthebasicloudness,bassand
brightnesssounddesired.
5. Adjust the “Clipper Drive” control (OO) as low as
possible for the loudness needed. This controls the
primaryloudnessvs.distortiontradeoff.Turningitup
makes the sound louder (but more distorted) while
turning it down makes the sound cleaner but not as
loud.Itshouldalwaysbesetaslowaspossibleforthe
levelofloudnessrequired.
6. Settheoverallamountofbassusingthe“Bass”control
(PP). At higher settings of the “Bass Thump” (QQ)
control,the “kick” or “Thump”action ofbass material
isemphasized.
7. Set the basic brightness of a preset by using the
“Presence” (RR), “Treble” (SS) and “Sparkle” (TT)
controls.Notethatthesethreecontrolsonlyboostthe
brightness.Asettingof“0.0”is“flat”ortheminimum
amount of boost for the particular preset that is
currently selected. Reducing brightness can be done,
forone example, by reducingthehigher bands of the
AGCorLimitermixers.
T
S
U
Z
AA
VW
Y
X
II
KK
JJ
LL
MM
BB
CC
DD
GG
HH
EE
FF
NN
OO
PP
RR
QQ
SS TT
NETWORK CONFIGURATION (CONT.) sysTEm CONFIGURATION sysTEm CONFIGURATION (CONT.) QUICK-sTART INsTAllATION GUIdE
OmNIA.11 sTEREO Fm AUdIO PROCEssOR
Items you need to supply:
• RackwithfouravailableEIArackspacesformounting
• Professionalline-levelanalogorAES/EBUdigitalaudio
sourcesonstandardXLRconnectors
• ConfiguredEthernetswitch
REQUIRED EQUIPMENT, CABLES, AND ACCESSORIES:
Thereareafewadditionalitemsrequiredforasuccessfulinstallation.Checkthelistbelowandmakesure
youhavewhatyouneed.
Included items:
• Omnia.11AudioProcessor
• ACPowercable
• Ethernetcable
• 4rackscrews
WehavemadethisOmniaSystemeasytosetupandconfigure.Thisquick-startguidewilltakeyouthroughthe
basicstepstoconfigureyournewOmnia.11tostartdeliveringcleaner,clearer,louder,andmoreconsistentsound.
Beforewegetstarted,let’smakesureyouhavewhatyouneed.
ThANK yOU FOR PURChAsING ThE OmNIA.11 sTEREO Fm
AUdIO PROCEssOR
CONTINUE TO sysTEm CONFIGURATION
Network configuration is complete. Your system is
readyforsystemconfiguration.Continuetothe“System
Configuration”instructions.
1. Once the system has rebooted, touch the “Setup”
button(S).
2. Touch the Livewire button (T). The Livewire
configurationscreenwillbedisplayed(U).
3. If you do not have a Livewire system, make sure
the 2 Livewire output channels are disabled. The
2 "Enable" buttons (V) will be white if Livewire
is disabled and green when enabled. To disable
Livewire, touch each of the two green "Enable"
buttons(V)toturnthemwhite.
4. If you do have a Livewire system, enable Livewire
bytouchingeachofthetwo"Enable"buttons(V)to
turnthemgreen.
5. IfyouhaveaLivewiresystem,touchthewhitefields
(W) next to the Output #1 and #2 and enter the
appropriatechannelvalueviathepop-upkeyboard(X).
6. Touchthe“APPLY”button(Y)undertheOutputs.
7. Touchthewhitefields(Z)nexttotheInput#1and#2
toentertheappropriatechannelvalueviathepop-
upkeyboard(X).
8. Touchthe“APPLY”buttonundertheInputs(AA).
lIVEWIRE CONFIGURATION
OUTPUT CONFIGURATION
1. Touchthe“Output”icon(II).TheOutputConfigurationscreenwillbedisplayed.Ifthe“Basic”tabisnot
active,touchtoselectit.
INPUT CONFIGURATION
1. Touchthe“ADJ”icon(BB)toreturntotheinitialSystemscreen.
2. Touchthe“Input”icon(CC).TheInputConfigurationscreenwillbedisplayed.Ifthe“Basic”tab(DD)
isnotactive,touchtoselectit.
3. Fromthe“InputSource”drop-down(EE),selecttheAnalog,AES/EBUorLivewireinputasappropriate
foryourinstallation.Ifyouraudiosourceisprovidinganaudiofeedyoushouldseemeteractivityon
thebargraphmeters(FF).
4. Whiledrivingtheinputswithtypicalprogrammaterialatnormaloperatinglevel,adjustthe
appropriate“Master”InputGaincontrol(GG)foryourinstallationuntilthepeak-readinginputbar
graphmetersarereadingjust“intotheyellow”(about–15to–12dBFSorso).Iftheleft/rightaudio
levelscomingintotheOmnia.11aresomewhatunbalanced,youcanadjustthe“RightTrim”control
(HH)tochangetheleveloftherightchannelaloneoveralimitedrange.
©2016TLSCorp.,AllRightsReserved. 1490-00099-001—QUICKSTARTGUIDE:OMNIA.11C16/15035
yOUR sETUP Is COmPlETE!
That’sit!YouarenowreadytoexperiencetheOmnia.11
forsoundlikeneverbefore.
1. Touchthe“FMOptions”button(JJ)ontheleftsideofthe
MenuAreaandensurethatthePre-Emphasis,Diversity
Delay(if present)and BS-412 settingsarecorrectfor
yoursystemandyourlocation.
2. Touch the appropriate button (KK) above the “FM
Options”buttontoselectthegroupofoutputcontrols
fortheoutputyouwillbeusing.Alloutputsareactive
simultaneously. Note: If you are using a conventional
AES/EBU L/R digital output to feed an FM exciter or
linearSTL,touchthe“AES/EBU”buttonandbesurethe
“OutputSelection”issetto“FM”andthe“De-emphasis”
isturned“OFF”fortheoutputbeingused.Foraccessto
thecompositeMPXstereogeneratoroutputleveland
stereo pilot controls, touch the “Composite” button.
Note that these controls simultaneously adjust the
OmniaDirectoutput levelsas well. Finally,adjustthe
appropriatecontrolsothatthepeakoutput/modulation
level is correct for the equipment that follows the
Omnia.11.
3. Touchthe“FM”iconbutton(LL)atthetopofthescreen
andthentouchthe“Preset”tab(MM)todisplaythelist
offactoryprocessingpresets.Ifthepresetlistislocked
(grayed-out),touchthe“padlock”icontounlockit.Once
unlocked,simplytouchthedesiredpresetnameinthe
listanditwillbeputdirectly“ontheair".Werecommend
listening to all factory presets to get a feel for their
differencesandthenselectonetostartwith.
4. Touch the “Quick Setup” tab (NN) and adjust the
followingcontrolstosetthebasicloudness,bassand
brightnesssounddesired.
5. Adjust the “Clipper Drive” control (OO) as low as
possible for the loudness needed. This controls the
primaryloudnessvs.distortiontradeoff.Turningitup
makes the sound louder (but more distorted) while
turning it down makes the sound cleaner but not as
loud.Itshouldalwaysbesetaslowaspossibleforthe
levelofloudnessrequired.
6. Settheoverallamountofbassusingthe“Bass”control
(PP). At higher settings of the “Bass Thump” (QQ)
control,the “kick” or “Thump”action ofbass material
isemphasized.
7. Set the basic brightness of a preset by using the
“Presence” (RR), “Treble” (SS) and “Sparkle” (TT)
controls.Notethatthesethreecontrolsonlyboostthe
brightness.Asettingof“0.0”is“flat”ortheminimum
amount of boost for the particular preset that is
currently selected. Reducing brightness can be done,
forone example, by reducingthehigher bands of the
AGCorLimitermixers.
T
S
U
Z
AA
VW
Y
X
II
KK
JJ
LL
MM
BB
CC
DD
GG
HH
EE
FF
NN
OO
PP
RR
QQ
SS TT
NETWORK CONFIGURATION (CONT.) sysTEm CONFIGURATION sysTEm CONFIGURATION (CONT.) QUICK-sTART INsTAllATION GUIdE
OmNIA.11 sTEREO Fm AUdIO PROCEssOR
Items you need to supply:
• RackwithfouravailableEIArackspacesformounting
• Professionalline-levelanalogorAES/EBUdigitalaudio
sourcesonstandardXLRconnectors
• ConfiguredEthernetswitch
REQUIRED EQUIPMENT, CABLES, AND ACCESSORIES:
Thereareafewadditionalitemsrequiredforasuccessfulinstallation.Checkthelistbelowandmakesure
youhavewhatyouneed.
Included items:
• Omnia.11AudioProcessor
• ACPowercable
• Ethernetcable
• 4rackscrews
WehavemadethisOmniaSystemeasytosetupandconfigure.Thisquick-startguidewilltakeyouthroughthe
basicstepstoconfigureyournewOmnia.11tostartdeliveringcleaner,clearer,louder,andmoreconsistentsound.
Beforewegetstarted,let’smakesureyouhavewhatyouneed.
ThANK yOU FOR PURChAsING ThE OmNIA.11 sTEREO Fm
AUdIO PROCEssOR
CONTINUE TO sysTEm CONFIGURATION
Network configuration is complete. Your system is
readyforsystemconfiguration.Continuetothe“System
Configuration”instructions.
1. Once the system has rebooted, touch the “Setup”
button(S).
2. Touch the Livewire button (T). The Livewire
configurationscreenwillbedisplayed(U).
3. If you do not have a Livewire system, make sure
the 2 Livewire output channels are disabled. The
2 "Enable" buttons (V) will be white if Livewire
is disabled and green when enabled. To disable
Livewire, touch each of the two green "Enable"
buttons(V)toturnthemwhite.
4. If you do have a Livewire system, enable Livewire
bytouchingeachofthetwo"Enable"buttons(V)to
turnthemgreen.
5. IfyouhaveaLivewiresystem,touchthewhitefields
(W) next to the Output #1 and #2 and enter the
appropriatechannelvalueviathepop-upkeyboard(X).
6. Touchthe“APPLY”button(Y)undertheOutputs.
7. Touchthewhitefields(Z)nexttotheInput#1and#2
toentertheappropriatechannelvalueviathepop-
upkeyboard(X).
8. Touchthe“APPLY”buttonundertheInputs(AA).
lIVEWIRE CONFIGURATION
OUTPUT CONFIGURATION
1. Touchthe“Output”icon(II).TheOutputConfigurationscreenwillbedisplayed.Ifthe“Basic”tabisnot
active,touchtoselectit.
INPUT CONFIGURATION
1. Touchthe“ADJ”icon(BB)toreturntotheinitialSystemscreen.
2. Touchthe“Input”icon(CC).TheInputConfigurationscreenwillbedisplayed.Ifthe“Basic”tab(DD)
isnotactive,touchtoselectit.
3. Fromthe“InputSource”drop-down(EE),selecttheAnalog,AES/EBUorLivewireinputasappropriate
foryourinstallation.Ifyouraudiosourceisprovidinganaudiofeedyoushouldseemeteractivityon
thebargraphmeters(FF).
4. Whiledrivingtheinputswithtypicalprogrammaterialatnormaloperatinglevel,adjustthe
appropriate“Master”InputGaincontrol(GG)foryourinstallationuntilthepeak-readinginputbar
graphmetersarereadingjust“intotheyellow”(about–15to–12dBFSorso).Iftheleft/rightaudio
levelscomingintotheOmnia.11aresomewhatunbalanced,youcanadjustthe“RightTrim”control
(HH)tochangetheleveloftherightchannelaloneoveralimitedrange.
©2016TLSCorp.,AllRightsReserved. 1490-00099-001—QUICKSTARTGUIDE:OMNIA.11C16/15035
yOUR sETUP Is COmPlETE!
That’sit!YouarenowreadytoexperiencetheOmnia.11
forsoundlikeneverbefore.
1. Touchthe“FMOptions”button(JJ)ontheleftsideofthe
MenuAreaandensurethatthePre-Emphasis,Diversity
Delay(if present)and BS-412 settingsarecorrectfor
yoursystemandyourlocation.
2. Touch the appropriate button (KK) above the “FM
Options”buttontoselectthegroupofoutputcontrols
fortheoutputyouwillbeusing.Alloutputsareactive
simultaneously. Note: If you are using a conventional
AES/EBU L/R digital output to feed an FM exciter or
linearSTL,touchthe“AES/EBU”buttonandbesurethe
“OutputSelection”issetto“FM”andthe“De-emphasis”
isturned“OFF”fortheoutputbeingused.Foraccessto
thecompositeMPXstereogeneratoroutputleveland
stereo pilot controls, touch the “Composite” button.
Note that these controls simultaneously adjust the
OmniaDirectoutput levelsas well. Finally,adjustthe
appropriatecontrolsothatthepeakoutput/modulation
level is correct for the equipment that follows the
Omnia.11.
3. Touchthe“FM”iconbutton(LL)atthetopofthescreen
andthentouchthe“Preset”tab(MM)todisplaythelist
offactoryprocessingpresets.Ifthepresetlistislocked
(grayed-out),touchthe“padlock”icontounlockit.Once
unlocked,simplytouchthedesiredpresetnameinthe
listanditwillbeputdirectly“ontheair".Werecommend
listening to all factory presets to get a feel for their
differencesandthenselectonetostartwith.
4. Touch the “Quick Setup” tab (NN) and adjust the
followingcontrolstosetthebasicloudness,bassand
brightnesssounddesired.
5. Adjust the “Clipper Drive” control (OO) as low as
possible for the loudness needed. This controls the
primaryloudnessvs.distortiontradeoff.Turningitup
makes the sound louder (but more distorted) while
turning it down makes the sound cleaner but not as
loud.Itshouldalwaysbesetaslowaspossibleforthe
levelofloudnessrequired.
6. Settheoverallamountofbassusingthe“Bass”control
(PP). At higher settings of the “Bass Thump” (QQ)
control,the “kick” or “Thump”action ofbass material
isemphasized.
7. Set the basic brightness of a preset by using the
“Presence” (RR), “Treble” (SS) and “Sparkle” (TT)
controls.Notethatthesethreecontrolsonlyboostthe
brightness.Asettingof“0.0”is“flat”ortheminimum
amount of boost for the particular preset that is
currently selected. Reducing brightness can be done,
forone example, by reducingthehigher bands of the
AGCorLimitermixers.
T
S
U
Z
AA
VW
Y
X
II
KK
JJ
LL
MM
BB
CC
DD
GG
HH
EE
FF
NN
OO
PP
RR
QQ
SS TT
Other manuals for 11
2
Table of contents
Other Omnia Recording Equipment manuals
Popular Recording Equipment manuals by other brands
Yamaha
Yamaha CRD-HD1300 Service manual
Iso-Max
Iso-Max CI-RJ2R-T user guide
Knoll
Knoll VS75 installation guide
Mitsubishi Electric
Mitsubishi Electric DX-NT400E Installation and operation manual
Lighted Piston
Lighted Piston LPC-1 installation instructions
Kantech
Kantech WinPass KT- 300 System reference manual
