Omnigates 31001074 User manual

User’s Manual
HDMI®EXTENDER over single UTP Cable
with IR Control
SKU: 31001074

Thank you for purchasing HDMI®Extender. For optimum performance and safety,
please read these instructions carefully before connecting, operating or adjusting
this product. Please keep this manual for future reference.
INTRODUCTION
The HDMI Extender over single UTP cable with IR extends high definition video and
audio signals and IR, at a distance of up to 164ft (50m) over a single Cat5e/6 cable.
Features EDID management, which allows and encourages source and display
"handshake" for seamless integration. With only one cost effective Cat5e/6 cable,
high definition sources with HDMI outputs can be connected to high definition
displays with HDMI inputs over long distances. Deep color video, DTS-HD or Dolby
TrueHD™ audio is supported and compatible with the extender. In addition, the
extender is also equipped with pass-through which allows for source control.
The Transmitter is used to capture the HDMI input with IR signals and carries the
signals via one cost effective Cat5e/6 cable. Receiver is responsible for equalizing
the transmitted HDMI signal and reconstructing IR control signals. The extender
offers the most convenient solution for HDMI extension over a single Cat5e/6 with
long distance capability, and is the perfect solution for any application.
FEATURES
1. Allows HDMI Audio/Video and IR signals to be transmitted over a single Cat5e/6
cable
2. Support copy EDID from receiver display or loop out display
3. Allows for cascading via additional HDMI loop out port
4. Support Power over ethernet cable function
5. Extends 1080p resolution up to 164ft/50m over a single Cat5e or Cat6 cable
6. Works with HDMI and HDCP compliant devices
7. Supports up to 1080p High Definition resolution
8. Compact design for an easy and flexible installation
PACKAGE CONTENTS
1x HDMI Transmitter
1x HDMI Receiver
1x Windband IR Tx cable
1x Windband IR Rx cable
2x 5V DC Power Adapter
User’s Manual
1

PRODUCT OVERVIEW
Transmitter
1. HDMI In: Connect HDMI devices
2. EDID:
Right - The extender will copy HDMI loop out display EDID information to source
Left - The extender will copy the Receiver dispaly EDID to source
3. HDMI Out: Connect to TV or monitor
4. IR Out: Connect the IR Blaster cable which should be in directly placed with the
equipment to be controlled
5. Power Indicator: Illuminate when connected with power supply
6. CAT: Connect the Transmitter and the Receiver with CAT 5E/6 cable
7. Link Indicator: Illuminates when the device is connected to HDMI source
8. DC 5V - Plug in included power adapter
Receiver
1. EQ Switcher: Receiver equalizer switcher
2. HDMI Out: Connect to TV or monitor
3. IR In: Connect the IR Receiver for IR signal reception. Ensure that the remote is
within the direct line-of-sight of the IR Receiver
4. Power Indicator: Illuminates when connected with power supply
5. CAT: Connect the Transmitter and the Receiver with CAT 5E/6 cable
6. Lock Indicator: Illuminates when the HDMI signal from the transmitter is stable
7. DC 5V - Plug in included power adapter
2
12 3
1 2 3 4 5 6 7
4 5 6 7 8

RX EQUALIZER DISTANCE ADJUST
If image on the display is flickering or blinking, adjust the EQ switch to improve the
cable skew. MAX stands for the strongest HDMI signal for the longest possible
transmission length while MIN stands for the weakest HDMI signal for short
transmission length. Adjust the signal level from MIN to MAX until desired video
quality is displayed.
3
Recommeded EQ Setting
Position Cable Length
Under 49.5ft (15m)
0 1
49.5 ~ 99ft (15 ~ 30m)
99 ~ 132ft (30 ~ 40m)
132 ~ 164ft (40 ~ 50m)
2 3
4 5
6 7

CONNECTION DIAGRAM
SPECIFICATIONS
Video Bandwidth
Video Support
Audio Support
Transmission Range
Input TMDS Signal
Input DDC Signal
ESD Protection
RJ-45 Connector
Power Supply
Power Consumption
Operation Temperature
Storage Temperature
Relative Humidity
: 4.95Gbps
: 480i / 480p / 720p / 1080i / 1080p@60
: Surround Sound (up to 7.1ch) or Stereo Digital Audio
: HD (1080p 24-bit color) - up to 164ft (50m)
: 3.3 volts
: 5.0 volts/P-P
: ±8kV (Air-gap discharge) & ±4kV (Contact discharge)
: WE/SS 8P8C
: 5V 1A DC
: 1.5W (Transmitter) / 1.0W (Receiver)
: 32°F ~ 104°F (0°C ~ 40°C)
: -4°F ~ 140°F (-20°C ~ 60°C)
: 20 ~ 90% RH
4

REGULATORY COMPLIANCE
Notice for FCC
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Modifying the equipment without Omnigates’ authorization may result in the equipment no longer
complying with FCC requirements for Class B digital devices. In that event, your right to use the
equipment may be limited by FCC regulations, and you may be required to correct any interference
to radio or television communications at your own expense.
This Equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
· Consult the dealer or an experienced radio/TV technician for help.
Radio Notice for FCC
Caution
This FCC Part 15 radio device operates on a non-interference basis with other devices operating
at this frequency. Any changes or modification to said product not expressly approved by
Omnigates, including the use of non-approved antennas, could void the user’s authority to operate
this device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
HDMI®, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Dolby®and the double-D symbol are registered trademarks of Dolby Laboratories. Dolby TrueHD™ is a trademark of
Dolby Laboratories.
DTS®, the Symbol, and DTS + the Symbol together are registered trademarks, and DTS Master Audio™ is a trademark
of DTS, Inc.
5