Omnitron Systems iConverter XM5 8261-0 User manual
1U 19” iConverter® XM5 NID Rack Mount Shelf
User Manual
PRODUCT OVERVIEW
The 8261-0 1U 19” XM5 Rack Mount Shelf accommodates two iConverter®XM5 Network
Interface Devices or two iConverter®XM5-1G Network Interface Devices.
1U Rack Mount Shelf
The shelf does not support the iConverter XM5 Aggregation Demarcation Device.
INSTALLATION PROCEDURE
1) Unpacking, Visual Inspection and Inventory
2) Rack Mounting
3) General Installation
4) Installing iConverter XM5 NIDs to the Shelf
1) UNPACKING, VISUAL INSPECTION AND INVENTORY
Review the contents. The following items should be included:
• 1URackMountShelf • UserManual
• Four(4)MountingBrackets • Eight(8)#4-401/4”Flatheadscrews
2) RACK MOUNTING
Mount and attach the shelf to the 19” standard rack using the appropriate rack mounting
screws (not included).
When rack-mounting the shelf, the rack should be appropriately earthgrounded. The shelf
providesNEBSgroundpoststosecureagroundinglugfromtheracktotheshelf.
Page 1
3) GENERAL INSTALLATION
Install the mounting brackets to the side of the XM5 using the supplied screws.
iConverter XM5 NIDs with mounting bracket
Removeanyrubberfeetbeforeinstallingthemodule/chassistotheshelf.
4) INSTALLING ICONVERTER XM5 NIDS TO THE SHELF
Slide the XM5 into the mounting guide slots on the shelf.
Installing iConverter XM5 NIDs on the Shelf
ContinuetoslidetheXM5untilitisushwiththefrontmountbracketontheshelf.Secure
the XM5 by fastening the thumbscrew (push in and turn clockwise to tighten) to the shelf.
XM5 NIDs Installed in the Shelf
Embedded cable tie down slots secure the power cord(s) and data cable(s) to the shelf
(cable ties not included).
Page 2
Page 3
General and Copyright Notice
This publication is protected by U.S. and international copyright laws. All rights reserved. The whole or
any part of this publication may not be reproduced, stored in a retrieval system, translated, transcribed,
or transmitted, in any form, or by any means, manual, electric, electronic, electromagnetic, mechanical,
chemical, optical or otherwise, without prior explicit written permission of Omnitron Systems Technology,
Inc.
The following trademarks are owned by Omnitron Systems Technology, Inc.: FlexPointTM, FlexSwitchTM,
iConverter®, miConverterTM, NetOutlook®, OmniLight®, OmniConverter®, RuggedNet®, Omnitron Systems
Technology, Inc.TM, OSTTM and the Omnitron logo.
All other company or product names may be trademarks of their respective owners.
The information contained in this publication is subject to change without notice. Omnitron Systems
Technology, Inc. is not responsible for any inadvertent errors.
Warranty
This product is warranted to the original purchaser (Buyer) against defects in material and workmanship
for a period of two (2) years from the date of shipment. A lifetime warranty may be obtained by the original
purchaserbyregisteringthisproductatwww.omnitron-systems.com/supportwithinninety(90)daysfrom
the date of shipment. During the warranty period, Omnitron will, at its option, repair or replace a product
which is proven to be defective with the same product or with a product with at least the same functionality.
For warranty service, the product must be sent to an Omnitron designated facility, at Buyer’s expense.
Omnitron will pay the shipping charge to return the product to Buyer’s designated US address using
Omnitron’s standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to product malfunctions resulting from improper or inadequate use
and/ormaintenanceoftheequipmentbyBuyer,Buyer-suppliedequipment,Buyer-suppliedinterfacing,
unauthorized modications or tampering with equipment (including removal of equipment cover by
personnelnotspecicallyauthorizedandcertiedbyOmnitron),ormisuse,oroperatingoutsidethe
environmentalspecicationoftheproduct(includingbutnotlimitedtovoltage,ambienttemperature,
radiation, unusual dust, etc.), or improper site preparation or maintenance.
Nootherwarrantyis expressedorimplied.Omnitronspecicallydisclaimsthe impliedwarrantiesof
merchantabilityandtnessforanyparticularpurpose.
The remedies provided herein are the Buyer’s sole and exclusive remedies. Omnitron shall not be liable
for any direct, indirect, special, incidental, or consequential damages, whether based on contract, tort,
or any legal theory.
Environmental Notices
The equipment covered by this manual must be disposed of or recycled in accordance with the Waste
ElectricalandElectronicEquipmentDirective(WEEEDirective)oftheEuropeanCommunitydirective
2012/19/EU on waste electrical and electronic equipment (WEEE) which, together with the RoHS
Directive2015/863/EU,for electricalandelectronicequipment soldintheEUafter July2019.Such
disposal must follow national legislation for IT and Telecommunication equipment in accordance with the
WEEEdirective:(a)Donotdisposewasteequipmentwithunsortedmunicipalandhouseholdwaste.(b)
Collect equipment waste separately. (c) Return equipment using collection method agreed with Omnitron.
TheequipmentismarkedwiththeWEEEsymbolshowntoindicatethatitmustbecollected
separately from other types of waste. In case of small items the symbol may be printed only on the
packaging or in the user manual. If you have questions regarding the correct disposal of equipment go
towww.omniton-systems.com/supportore-mailtoOmnitronat[email protected].
CUSTOMER SUPPORT INFORMATION
Phone: (949) 250-6510
Fax: (949) 250-6514
Address: Omnitron Systems Technology, Inc.
38 Tesla
Irvine, CA 92618, USA
URL: www.omnitron-systems.com
040-08261-001B10/22
Page 4
Other Omnitron Systems Chassis manuals
