OMPHOBBY EDGE 540 User manual

GlobalProfessionalRCModelBrand
InstallationManual
OMPHOBBY106”Edge540KevlarReinforced
BalsaAirplane
ZhuhaiEdgeSmartDriveTechnologyCo.,Ltd.
www.omphobby.com

OMPHobby106”BalsaAirplane
ZhuhaiEdgeSmartDriveTechnologyCo.,Ltd.
www.omphobby.com

OMPHobby106”Edge540BalsaAirplane
ZhuhaiEdgeSmartDriveTechnologyCo.,Ltd.
www.omphobby.com
Options:Threecolorsforchoosing:
Orange-White,Green-Black,Red-White
Unboxing-What’sintheBox?

ZhuhaiEdgeSmartDriveTechnologyCo.,Ltd.
www.omphobby.com
LandinggearAssembly
LandingGearInstallation
4. Unscrewhexagonscrewsonthelandinggearplate,
applythreadlockertohexagonscrews,useittosecure
thecarbonfiberlandinggeartolandinggearplate.
1. Landinggearparts
2. Installwheels,securewheelswithgasketandscrew.(Apply
threadlockertoscrews)
3. Putthecuffthroughthelandgearbeforeinstallthewheel
5. Putlandinggearcoverplateintoaslotandstickitwith
transparenttape.

ZhuhaiEdgeSmartDriveTechnologyCo.,Ltd.
www.omphobby.com
TailwheelAssembly
Installthetailwheelassemblyusingwashersandsockethead
screws.PleaseapplyanaerobicadhesiveandlockthreeM3
fixingscrewsbeforeinstallation.
TailWheelInstallation
LandinggearAssembly
6. Securethecuffswithscrews.Becarefultonotbreakthe
screws.Ifthescrewseemstobedifficulttoinsertuseadrill
toopenupthehole.(Somepeoplehavefoundtheyprefera
dobofsiliconeinsidethecuffholdthemsecure.)

ZhuhaiEdgeSmartDriveTechnologyCo.,Ltd.
www.omphobby.com
ControlHornsAssembly
1. Carefullylocatetheslotswhichhavebeenmadeonelevators,
ailerons,rudder,lightlycutthroughthecoveringbutnotinto
thebalsasheeting.
2. Usesandpapertoscufftherootofcontrolhornsforagoodglue
bond.Trytoinsertitintothemountingslotstoadjustthe
positionfirst.
3. Putthecontrolhornsreinforcingpiece,dropthehornsinthe
holes,positionedcorrectlywhenthehornsaredirectlyabove
thehingeline,thenstickmaskingtapearoundthereinforcing
pieceasshowninthepicture,cutabout1mminsidewithaknife
andremovethecovering,belowtoexposethepre‐cutslots.

ZhuhaiEdgeSmartDriveTechnologyCo.,Ltd.
www.omphobby.com
ControlHornsAssembly
4. Applyepoxyinsidethepre‐cutslots,andcoatthehornswith
epoxyasshown.
5. Fitthehornsintothelockingplateandtheninsertthemintothe
pre‐cutslots.Aligntherightandleftsidesbeforetheepoxy
cures.Wipeawayexcessepoxywithrubbingalcohol.

ZhuhaiEdgeSmartDriveTechnologyCo.,Ltd.
www.omphobby.com
ServoAssembly
ElevatorServoAssembly
Installservosasshownwiththeservolabelfacingtowardtherear
ofthefuselage.
Installtheservoarmintheverticalposition.Adjustthepushrod
lengthsothattheservoandelevatorarebothintheneutral
position.

ZhuhaiEdgeSmartDriveTechnologyCo.,Ltd.
www.omphobby.com
Engineandthethrottleservoinstallation
Measurethelengthoftheenginefromthefirewalltotheprop
thrustwasher.Measurethedistancerequiredforthepropthrust
washertoclearthefrontofthecowlby¼”to½”thenmarkthe
firewallpositionontheenginemount.
Orusetheenginemountingholeboardfromsparepartsbagto
markanddrilltheholes.
Cutoutfrompaperboardorcardboardasatemplateforventhole

ZhuhaiEdgeSmartDriveTechnologyCo.,Ltd.
www.omphobby.com
Beforeinstallingtheairdeflector,pleaseclampthecowlto
determinethegapwiththecylinderandtrimit,thenuseepoxyglue
tofix
Engineandthethrottleservoinstallation