Omron SYSMAC CS Series User manual

OPERATION MANUAL
Cat. No. W368-E1-03
SYSMAC
CS Series
Analog I/O Units
CS1W-PTS01-V1/PTS02/PTS03/PTW01/
PDC01/PTR01/PTR02/PPS01/PMV01/PMV02

CS Series
CS1W-PTS01-V1/PTS02/PTS03/PTW01/
PDC01/PTR01/PTR02/PPS01/PMV01/PMV02
Analog I/O Units
Operation Manual
Revised May 2002

iv

v
Notice:
OMRON products are manufactured for use according to proper procedures by a qualified operator
and only for the purposes described in this manual.
The following conventions are used to indicate and classify precautions in this manual. Always heed
the information provided with them. Failure to heed precautions can result in injury to people or dam-
age to property.
!DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
!WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
!Caution Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury, or property damage.
OMRON Product References
All OMRON products are capitalized in this manual. The word “Unit” is also capitalized when it refers to
an OMRON product, regardless of whether or not it appears in the proper name of the product.
The abbreviation “Ch,” which appears in some displays and on some OMRON products, often means
“word” and is abbreviated “Wd” in documentation in this sense.
The abbreviation “PC” means Programmable Controller and is not used as an abbreviation for anything
else.
Visual Aids
The following headings appear in the left column of the manual to help you locate different types of
information.
Note Indicates information of particular interest for efficient and convenient opera-
tion of the product.
1,2,3... 1. Indicates lists of one sort or another, such as procedures, checklists, etc.
OMRON, 2000
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, o
r
by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission o
f
OMRON.
No patent liability is assumed with respect to the use of the information contained herein. Moreover, because OMRON is con-
stantly striving to improve its high-quality products, the information contained in this manual is subject to change without
notice. Every precaution has been taken in the preparation of this manual. Nevertheless, OMRON assumes no responsibility
for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained in
this publication.

vi

vii
TABLE OF CONTENTS
PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
1 Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
2 General Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
3 Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
4 Operating Environment Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
5 Application Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xiv
6 Conformance to EC Directives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv
SECTION 1
Overview and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1-1 Overview of Analog I/O Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1-2 Features and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1-3 System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1-4 Specifications and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
1-5 Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
1-6 Error Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1-7 Specification Changes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
SECTION 2
Individual Unit Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . 29
2-1 CS1W-PTS01-V1 Isolated-type Thermocouple Input Unit . . . . . . . . . . . . . . . . . . . . . . . . . 30
2-2 CS1W-PTS02 Isolated-type Resistance Thermometer Input Unit . . . . . . . . . . . . . . . . . . . . 41
2-3 CS1W-PTS03 Isolated-type Resistance Thermometer Input Unit . . . . . . . . . . . . . . . . . . . . 51
2-4 CS1W-PTW01 2-Wire Transmitter Input Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
2-5 CS1W-PDC01 Analog Input Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
2-6 CS1W-PTR01 Power Transducer Input Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
2-7 CS1W-PTR02 Analog Input Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
2-8 CS1W-PPS01 Isolated-type Pulse Input Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
2-9 CS1W-PMV01 Isolated-type Analog Output Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
2-10 CS1W-PMV02 Isolated-type Analog Output Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Appendices
A Supplementary Explanation of Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
B Zero/Span Adjustment Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

ix
About this Manual:
This manual describes the installation and operation of the CS-series Analog I/O Units and includes
the sections described below.
In this manual, “Analog I/O Units” is a product group name for the following groups of Units.
Please read this manual carefully and be sure you understand the information provided before
attempting to install and operate the Analog I/O Units.
Section 1 presents an overview of the CS-series Analog I/O Units, and outlines their common fea-
tures.
Section 2 describes each of the Analog I/O Units in detail.
Appendix A provides a supplementary explanation of Unit functions.
Appendix B provides an example of zero/span adjustment.
Name Model number
Isolated-type Thermocouple Input Unit CS1W-PTS01-V1
Isolated-type Resistance Thermometer Input Unit CS1W-PTS02
Isolated-type Resistance Thermometer Input Unit (Ni508.4 Ω) CS1W-PTS03
Isolated-type 2-Wire Transmitter Input Unit CS1W-PTW01
Isolated-type Analog Input Unit CS1W-PDC01
Power Transducer Input Unit CS1W-PTR01
Analog Input Unit CS1W-PTR02
Isolated-type Pulse Input Unit CS1W-PPS01
Isolated-type Analog Output Unit CS1W-PMV01/PMV02
!WARNING Failure to read and understand the information provided in this manual may result in per-
sonal injury or death, damage to the product, or product failure. Please read each section
in its entirety and be sure you understand the information provided in the section and
related sections before attempting any of the procedures or operations given.

xi
PRECAUTIONS
This section provides general precautions for usingthe CS-series Programmable Controllers (PCs) and related devices.
The information contained in this section is important for the safe and reliable application of Programmable
Controllers. You must read this section and understand the information contained before attempting to set up
or operate a PC system.
1 Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
2 General Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
3 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
4 Operating Environment Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
5 Application Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv
6 Conformance to EC Directives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv
6-1 Applicable Directives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv
6-2 Concepts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv
6-3 Conformance to EC Directives . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv

xii
Intended Audience 1
1 Intended Audience
This manual is intended for the following personnel, who must also have
knowledge of electrical systems (an electrical engineer or the equivalent).
• Personnel in charge of installing FA systems.
• Personnel in charge of designing FA systems.
• Personnel in charge of managing FA systems and facilities.
2 General Precautions
The user must operate the product according to the performance specifica-
tions described in the operation manuals.
Before using the product under conditions which are not described in the
manual or applying the product to nuclear control systems, railroad systems,
aviation systems, vehicles, combustion systems, medical equipment, amuse-
ment machines, safety equipment, and other systems, machines, and equip-
ment that may have a serious influence on lives and property if used
improperly, consult your OMRON representative.
Make sure that the ratings and performance characteristics of the product are
sufficient for the systems, machines, and equipment, and be sure to provide
the systems, machines, and equipment with double safety mechanisms.
This manual provides information for programming and operating the Unit. Be
sure to read this manual before attempting to use the Unit and keep this man-
ual close at hand for reference during operation.
!WARNING It is extremely important that a PC and all PC Units be used for the specified
purpose and under the specified conditions, especially in applications that can
directly or indirectly affect human life. You must consult with your OMRON
representative before applying a PC System to the above-mentioned applica-
tions.
3 Safety Precautions
!WARNING Do not attempt to take any Unit apart while the power is being supplied. Doing
so may result in electric shock.
!WARNING Provide safety measures in external circuits (i.e., not in the Programmable
Controller), including the following items, to ensure safety in the system if an
abnormality occurs due to malfunction of the PC or another external factor
affecting the PC operation. Not doing so may result in serious accidents.
• Emergency stop circuits, interlock circuits, limit circuits, and similar safety
measures must be provided in external control circuits.
• Unless otherwise stated, the PC will turn OFF all outputs when its self-
diagnosis function detects any error or when a severe failure alarm
(FALS) instruction is executed. (The operation of outputs from Analog
Output Units is described later in this manual.) As a countermeasure for
such errors, external safety measures must be provided to ensure safety
in the system.
• The PC outputs may remain ON or OFF due to deposition or burning of
the output relays or destruction of the output transistors. As a counter-
measure for such problems, external safety measures must be provided
to ensure safety in the system.
• When the 24-VDC output (service power supply to the PC) is overloaded
or short-circuited, the voltage may drop and result in the outputs being
turned OFF. As a countermeasure for such problems, external safety
measures must be provided to ensure safety in the system.

xiii
Operating Environment Precautions 4
!WARNING Always turn OFF the power supply to the PC before attempting any of the fol-
lowing. Not turning OFF the power supply may result in malfunction or electric
shock.
• Mounting or dismounting the Power Supply Units, I/O Units, CPU Units, or
any other Units.
• Assembling the Units.
• Setting DIP switches or rotary switches.
• Connecting cables or wiring the system.
• Connecting or disconnecting the connectors.
!WARNING Do not attempt to disassemble, repair, or modify any Units. Any attempt to do
so may result in malfunction, fire, or electric shock.
!Caution Execute online edit only after confirming that no adverse effects will be
caused by extending the cycle time. Otherwise, input signals may not be read-
able.
4 Operating Environment Precautions
!Caution Do not operate the control system in the following locations:
• Locations subject to direct sunlight.
• Locations subject to temperatures or humidity outside the range specified
in the specifications.
• Locations subject to condensation as the result of severe changes in tem-
perature.
• Locations subject to corrosive or flammable gases.
• Locations subject to dust (especially iron dust) or salts.
• Locations subject to exposure to water, oil, or chemicals.
• Locations subject to shock or vibration.
!Caution Take appropriate and sufficient countermeasures when installing systems in
the following locations:
• Locations subject to static electricity or other forms of noise.
• Locations subject to strong electromagnetic fields.
• Locations subject to possible exposure to radioactivity.
• Locations close to power supplies.
!Caution The operating environment of the PC System can have a large effect on the
longevity and reliability of the system. Improper operating environments can
lead to malfunction, failure, and other unforeseeable problems with the PC
System. Be sure that the operating environment is within the specified condi-
tions at installation and remains within the specified conditions during the life
of the system.

xiv
Application Precautions 5
5 Application Precautions
Observe the following precautions when using the Analog I/O Unit.
• If any one of cold junction compensating elements is disconnected, no
compensation will be performed, resulting in improper temperature mea-
surement. Do not disconnect cold junction compensating elements.
(Applicable to the CS1W-PTS01-V1 Isolated-type Thermocouple Input
Unit.)
• Each cold junction compensation element is calibrated for the individual
Unit and connected circuit; do not use elements from other Units or
replace two elements of the same Unit. Doing so will result in improper
temperature measurement. Use elements attached at the time of product
delivery. (Applicable to the CS1W-PTS01-V1 Isolated-type Thermocouple
Input Unit.)
• Check the user program for proper execution before actually running it on
the Unit. Not checking the program may result in an unexpected opera-
tion.
• Fail-safe measures must be taken by the customer to ensure safety in the
event of incorrect, missing, or abnormal signals caused by broken signal
lines, momentary power interruptions, or other causes.
• Confirm that no adverse effect will occur in the system before attempting
any of the following. Not doing so may result in an unexpected operation.
• Changing the operating mode of the PC.
• Force-setting/force-resetting any bit in memory.
• Changing the present value of any word or any set value in memory.
• Be sure that all the mounting screws, terminal screws, and cable connec-
tor screws are tightened to the torque specified in this manual. Incorrect
tightening torque may result in malfunction.
• Be sure that the terminal blocks, expansion cables, and other items with
locking devices are properly locked into place. Improper locking may
result in malfunction.
• Take appropriate measures to ensure that the specified power with the
rated voltage and frequency is supplied in places where the power supply
is unstable. An incorrect power supply may result in malfunction.
• Leave the label attached to the Unit when wiring. Removing the label may
result in malfunction if foreign matter enters the Unit.
• Remove the label after the completion of wiring to ensure proper heat dis-
sipation. Leaving the label attached may result in malfunction.
• Use crimp terminals for wiring. Do not connect bare stranded wires
directly to terminals. Connection of bare stranded wires may result in
burning.
• Do not apply voltages to the input section in excess of the rated input volt-
age. Excess voltages may result in burning.
• Do not apply voltages or connect loads to the output section in excess of
the maximum switching capacity. Excess voltage or loads may result in
burning.
• Double-check all wiring and switch settings before turning ON the power
supply. Incorrect wiring may result in burning.
• Resume operation only after transferring to the new CPU Unit the con-
tents of the DM Area, HR Area, and other data required for resuming
operation. Not doing so may result in an unexpected operation.

xv
Conformance to EC Directives 6
6 Conformance to EC Directives
6-1 Applicable Directives
•EMCDirectives
• Low Voltage Directive
6-2 Concepts
EMC Directives
OMRON devices that comply with EC Directives also conform to the related
EMC standards so that they can be more easily built into other devices or the
overall machine. The actual products have been checked for conformity to
EMC standards (see the following note). Whether the products conform to the
standards in the system used by the customer, however, must be checked by
the customer.
EMC-related performance of the OMRON devices that comply with EC Direc-
tives will vary depending on the configuration, wiring, and other conditions of
the equipment or control panel on which the OMRON devices are installed.
The customer must, therefore, perform the final check to confirm that devices
and the overall machine conform to EMC standards.
Note Applicable EMC (Electromagnetic Compatibility) standards are as follows:
EMS (Electromagnetic Susceptibility): EN61000-6-2
EMI (Electromagnetic Interference): EN50081-2
(Radiated emission: 10-m regulations)
Low Voltage Directives
Always ensure that devices operating at voltages of 50 to 1,000 V AC and 75
to 1,500 V DC meet the required safety standards for the PC (EN61131-2).
6-3 Conformance to EC Directives
The CS-series PCs comply with EC Directives. To ensure that the machine or
device in which a CS-series PC is used complies with EC Directives, the PC
must be installed as follows:
• The CS-series PC must be installed within a control panel.
• You must use reinforced insulation or double insulation for the DC power
supplies used for the communications power supply and I/O power sup-
plies.
• CS-series PCs complying with EC Directives also conform to the Com-
mon Emission Standard (EN50081-2). Radiated emission characteristics
(10-m regulations) may vary depending on the configuration of the control
panel used, other devices connected to the control panel, wiring, and
other conditions. You must therefore confirm that the overall machine or
equipment complies with EC Directives.

1
SECTION 1
Overview and Features
This section presents an overview of the CS-series Analog I/O Units and outlines their features.
1-1 Overview of Analog I/O Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1-2 Features and Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1-3 System Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1-4 Specifications and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1-4-1 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1-4-2 Nomenclature and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1-4-3 Exchanging Data with the CPU Unit. . . . . . . . . . . . . . . . . . . . . . . . 15
1-4-4 Mounting the Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
1-4-5 Precautions when Handling Units . . . . . . . . . . . . . . . . . . . . . . . . . . 20
1-4-6 Connecting Crimp Terminals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
1-4-7 Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
1-5 Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
1-6 Error Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1-7 Specification Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

2
Overview of Analog I/O Units Section 1-1
1-1 Overview of Analog I/O Units
There are nine Analog I/O Unit models, as shown in the following table.
Name Model Number
of I/O Field I/O isolation I/O type Main functions
Isolated-type Ther-
mocouple Input
Unit
CS1W-PTS01-
V1 4 inputs All inputs are iso- lated. B, E, J, K, N, R, S, T, mV • Variable range setting
• Process value scaling
• Process value alarm
• Mean value processing
• Rate-of-change calcula-
tion and alarm
• Alarm-ON delay
• Disconnection detection
Isolated-type
Resistance Ther-
mometer Input
Unit
CS1W-PTS02 4 inputs All inputs are iso-
lated. Pt100 (JIS, IEC), JPt100 • Variable range setting
• Process value scaling
• Process value alarm
• Mean value processing
• Rate-of-change calcula-
tion and alarm
• Alarm-ON delay
• Disconnection detection
Isolated-type
Resistance Ther-
mometer Input
Unit (Ni508.4 Ω)
CS1W-PTS03 4 inputs All inputs are iso-
lated. Ni508.4 Ω• Variable range setting
• Process value scaling
• Process value alarm
• Mean value processing
• Rate-of-change calcula-
tion and alarm
• Alarm-ON delay
• Disconnection detection
Isolated-type 2-
Wire Transmitter
Input Unit
CS1W-PTW01 4 inputs All inputs are iso-
lated. 4 to 20 mA from 2- wire transmitter.
4 to 20 mA, 1 to
5V
• Built-in power supply for 2-
wire transmitter
• Process value scaling
• Process value alarm
• Mean value processing
• Rate-of-change calcula-
tion and alarm
• Alarm-ON delay
• Input error detection
Isolated-type Ana-
log Input Unit CS1W-PDC01 4 inputs All inputs are iso- lated. –10 to 10 V, 0 to 10 V, –5 to 5 V, 0 to
5 V, 1 to 5 V, ±10 V
DC variable range,
4 to 20 mA, 0 to
20 mA
• Process value scaling
• Square root
• Process value alarm
• Mean value processing
• Rate-of-change calcula-
tion and alarm
• Alarm-ON delay
• Input error detection
Power Transducer
Input Unit CS1W-PTR01 8 inputs No isolation between inputs –1 to 1 mA, 0 to 1mA • Anti-overshooting at motor
startup
• Process value scaling
• Process value alarm
• Inrush input limit
• Alarm-ON delay
• Mean value processing
Analog Input Unit
(100 mV) CS1W-PTR02 8 inputs No isolation between inputs –100 to 100 mV, 0 to 100 mV • Process value scaling
• Process value alarm
• Inrush input limit
• Alarm-ON delay
• Mean value processing

3
Features and Functions Section 1-2
1-2 Features and Functions
I/O Isolation The Analog I/O Units listed below have isolation between inputs or outputs.
Therefore sneak circuits do not occur between thermocouples or between the
power supply’s common voltage inputs, so there is no need to utilize a signal
converter to prevent sneak circuits.
CS1W-PTS01-V1 Isolated-type Thermocouple Input Unit
CS1W-PTS02/PTS03 Isolated-type Resistance Thermometer Input Unit
CS1W-PTW01 Isolated-type 2-Wire Transmitter Input Unit
CS1W-PDC01 Isolated-type Analog Input Unit
CS1W-PPS01 Isolated-type Pulse Input Unit
CS1W-PMV01/PMV02 Isolated-type Analog Output Unit
Isolated-type
Pulse Input Unit CS1W-PPS01 4 inputs All inputs are iso- lated. No-voltage semi- conductor input or
voltage input: 0 to
20,000 pulses/s
Contact input: 0 to
20 pulses/s
• Sensor power supply:
12 V DC, built-in
• Instantaneous value scal-
ing
• Mean value processing
• Instantaneous value alarm
• Alarm-ON delay
• Accumulated value output
Isolated-type Ana-
log Output Unit CS1W-PMV01 4 outputs All outputs are iso- lated. 4 to 20 mA, 1 to 5V • Output disconnection
alarm
• Answer input
• Output rate-of-change limit
• Output high/low limits
• Output hold when CPU
Unit error occurs
• Output disconnection
detection
Isolated-type Ana-
log Output Unit CS1W-PMV02 4 outputs All outputs are iso- lated. −10 to 10 V, 0 to 10 V, −5 to 5 V, 0 to
5 V, −1 to 1 V, 0 to
1 V
• Output rate-of-change limit
• Output high/low limits
• Output hold when CPU
Unit error occurs
Name Model Number
of I/O Field I/O isolation I/O type Main functions
Analog I/O Unit
Isolation
Isolation
Isolation

4
Features and Functions Section 1-2
Variable Input Range
Setting For the Analog I/O Units listed below, the input range can be set by the user
according to the application. The internal settings will be switched automati-
cally, and measurements will be enabled within the appropriate operating
range. This function applies to the following Units:
CS1W-PTS01-V1 Isolated-type Thermocouple Input Unit
CS1W-PTS02 Isolated-type Resistance Thermometer Input Unit
CS1W-PDC01 Isolated-type Analog Input Unit
Note The accuracy and resolution are the values for the internal range that is set.
Process Value (or
Instantaneous Value)
Scaling in Industrial Units
This function takes the value scaled in industrial units with respect to the ana-
log (or pulse) input signal’s zero point and span point, and transfers it to the
CPU Unit as the process value (or instantaneous value). Because of this, no
ladder program is required at the CPU Unit for scaling.
Note It also possible to set the process value scaling zero/span point in reverse to
create an inverse relationship.
This function is supported by the following Units:
CS1W-PTS01-V1 Isolated-type Thermocouple Input Unit
CS1W-PTS02/PTS03 Isolated-type Resistance Thermometer Input Unit
CS1W-PTW01 Isolated-type 2-Wire Transmitter Input Unit
CS1W-PDC01 Isolated-type Analog Input Unit
CS1W-PTR01 Power Transducer Input Unit
CS1W-PTR02 Analog Input Unit (100 mV)
CS1W-PPS01 Isolated-type Pulse Input Unit
Process Value Alarm
(2 or 4 Points) Either a 2-point alarm (H and L limits) or a 4-point alarm (HH, H, L, and LL lim-
its) is possible for the process value (or instantaneous value).
This function is supported by the following Units:
CS1W-PTS01-V1 Isolated-type Thermocouple Input Unit
CS1W-PTS02/PTS03 Isolated-type Resistance Thermometer Input Unit
CS1W-PTW01 Isolated-type 2-Wire Transmitter Input Unit
CS1W-PDC01 Isolated-type Analog Input Unit
CS1W-PTR01 Power Transducer Input Unit
CS1WPTR02 Analog Input Unit (100 mV)
CS1W-PPS01 Isolated-type Pulse Input Unit
Measurable temperature range
Operating
temperature
range
Zero Span
Input signal
Industrial unit

5
Features and Functions Section 1-2
Rate-of-change
Calculation and Alarm The Analog I/O Units listed below calculate the rate of change for the process
value, and output an alarm when the high or low limit is exceeded. The rate-
of-change value is derived by taking the difference each second between the
process value at that time and the process value before the comparison time
interval. The comparison time interval can be set from 1 to 16 seconds. This
allows even a small process value rate of change to be detected.
This function is supported by the following Units:
CS1W-PTS01-V1 Isolated-type Thermocouple Input Unit
CS1W-PTS02/PTS03 Isolated-type Resistance Thermometer Input Unit
CS1W-PTW01 Isolated-type 2-Wire Transmitter Input Unit
CS1W-PDC01 Isolated-type Analog Input Unit
Alarm output
Alarm output
Alarm setting
Alarm setting
LL
(low low limit) L (low limit) H (high limit) HH (high high limit)
Process value input
L (low limit) H (high limit)
Process value input

6
Features and Functions Section 1-2
Note The rate of change is calculated every second (and not just once during the
comparison time interval) so that even minute changes in the process value
are detected.
Alarm Hysteresis An hysteresis can be set for the process value (or instantaneous value) alarm
and the rate-of-change alarm. The operation is as shown in the following dia-
gram.
This function is supported by the following Units:
CS1W-PTS01-V1 Isolated-type Thermocouple Input Unit
CS1W-PTS02/PTS03 Isolated-type Resistance Thermometer Input Unit
CS1W-PTW01 Isolated-type 2-Wire Transmitter Input Unit
CS1W-PDC01 Isolated-type Analog Input Unit
CS1W-PTR01 Power Transducer Input Unit
CS1W-PTR02 Analog Input Unit (100 mV)
CS1W-PPS01 Isolated-type Pulse Input Unit
Process value
Time
Process value
Time
Process value (comparison time interval: 3 s)
Time
Comparison time interval
set from 1 s to 16 s
Rate of change
(See note.) Rate-of-change high
limit alarm setting
Time
Rate-of-change high
limit alarm output
Time
Alarm output
Alarm setting
Hysteresis
Process value input
and rate of change

7
Features and Functions Section 1-2
Alarm-ON Delay This function can be used to set a given time period (0 s to 60 s) for delaying
the turning ON of the alarm after the process value (or instantaneous value)
alarm status or the alarm setting is reached. One alarm-ON delay is set for
each input or output. The same setting is used for all process value alarms
(HH, H, L, LL) and rate-of-change alarms (H, L).
This function is supported by the following Units:
CS1W-PTS01-V1 Isolated-type Thermocouple Input Unit
CS1W-PTS02/PTS03 Isolated-type Resistance Thermometer Input Unit
CS1W-PTW01 Isolated-type 2-Wire Transmitter Input Unit
CS1W-PDC01 Isolated-type Analog Input Unit
CS1W-PTR01 Power Transducer Input Unit
CS1W-PTR02 Analog Input Unit (100 mV)
CS1W-PPS01 Isolated-type Pulse Input Unit
Mean Value Processing The moving average of a specified number (from 1 to 16) of past process val-
ues (or instantaneous values) can be calculated and stored as the process
value. An input noise filter can be installed if erroneous process values are
obtained due to noise, or if the system has sudden voltage or current fluctua-
tions.
This function is supported by the following Units:
CS1W-PTS01-V1 Isolated-type Thermocouple Input Unit
CS1W-PTS02/PTS03 Isolated-type Resistance Thermometer Input Unit
CS1W-PTW01 Isolated-type 2-Wire Transmitter Input Unit
CS1W-PDC01 Isolated-type Analog Input Unit
CS1W-PTR01 Power Transducer Input Unit
CS1W-PTR02 Analog Input Unit (100 mV)
CS1W-PPS01 Isolated-type Pulse Input Unit
Note For the CS1W-PTR01 and CS1W-PTR02, four process values are always
averaged.
Example: H alarm setting
Time
Alarm output
Time
ON delay time (0 s to 60 s)
Process value