Model
V680-HAM42-FRT
FLRemoteID
INSTRUCTION SHEET
Observe the following precautions to ensure safe usage of the product.
1.
Do not use the product in environments subject to inflammable, explosive,
or corrosive gas.
2. Do not disassemble, repair, or modify the product in any way.
3. Tighten the mounting screws securely.
4. Because a cable has a locking mechanism, make sure that it has been
locked before using the cable.
5. Confirm that the DC power supply is within the rated power supply
voltage (24 VDC +10%/-15%) before using it.
6. Do not reverse polarity when connecting the power supply.
7. Do not allow water to enter or insert wire in the gaps of the case. Fire or
electric shock may result.
8. Provide enough space around the controller for ventilation.
9. Avoid setting up the unit near a highly heat-generating device
(such as heater, transformer and large-capacity resistor).
10. Always turn OFF the power supply to the product before attaching or
removing the Antenna.
11. If you suspect that anything is wrong with the product at any time, stop
using it immediately, turn OFF the power supply, and consult with your
OMRON representative.
12. When disposing of the product, dispose of it as industrial waste.
13. Do not use thinners, benzenes, acetones and kerosenes for cleaning.
PRECAUTION FOR SAFE USE
SAFETY PRECAUTIONS
Meaning of Signal Words
WARNING
Alert statements
WARNING
Indicatesapotentiallyhazardoussituation
which,ifnotavoided,couldresultindeath
orseriousinjury.
Additionally,theremaybesevereproperty
damage.
Thisproductisnotdesignedorratedforensuring
safetyofpersons.
Donotuseitforsuchpurposes.
NOTICE:
This product meets CISPR11 class A. The intended use of
this product is in an industrial environment only.
Dimensions （Unit：ｍｍ）
65
20 10 55 5
12 6 18
65
16
4 1.5
65
41.8
28.5
40
17.8 21.5
5.06
22.6
35.2
(3.7)
12
5
ANTENNA CONNECTOR
POWER TERMINAL
FL REMOTE
CONNECTOR
MODE SWITCH
NODE ADDRESS
SWITCH
STATUS INDICATOR DATA INDICATOR
General specifications
Characteristic Specification
Supply voltage24 VDC (-15%to10%)
Power consumption
Up to 6W
Ambient operating
temperature
-10 to 55℃(no freezing)
25 to 85%(no dewcondensation)
-25 to 65℃(no freezing)
25 to 85%(no dewcondensation)
Insulation resistans20MΩmin.（with 500V DC mega）
Between terminals (except for grand)and casing
Between terminals (except for grand)and grand
Withstand voltage1,000VAC, 50/60 Hz, 1min
Between terminals (except for grand)and casing
500VAC, 50/60 Hz, 1min
Between terminals (except for grand)and grand
Vibration resistanse Mechanical durability: 10 to 150 Hz, double amplitude: 0.2mm
with 10 sweep of 8 mineach in 3 directions
Shock resistance
Mechanical durability: 150m/s2,3times eachin 6directions
Dimensions 65×65 ×65 mm (excluding protruding parts)
Degree of protection
Panel-mounting (conforms to IP20)
Material PC/ABS resin
Weight Approx. 150 g
Mounting methodDIN Track
Ambient operating
humidity
Ambient storage
temperature
Ambient storage
humidity
1.
Installation Location
Do not install and storage the product in the follwing locations:
・Locations subject to corrosive gases, dust, dirt, metal powder, or salt.
・Locations where the specified ambient temperature range is exceeded.
・Locations subject to extreme temperature changes that may result in
condensation.
・Locations where the specified ambient humidity range is exceeded.
・Locations where the product would be directly subjected to vibration or
shock exceeding specifications.
・Locations subject to contact with water, oil, or chemicals
2.
Installation
・The product uses the 13.56MHz frequency band to communicate with
Tags. Some devices, such as some tranceivers, mortors, inverters, and
switch mode power supplies, generate electromagnetic waves (i.e., noise)
that can affect communications with the Tags. If any of these devices are
nearby, communications with Tags may be affected or Tags may be
destroyed, If the product is to be used near such devices, check the
effects on communications before using the product.
・To minimize the general influence of noise, follow the following
precautions:
(1)Ground the earth terminal of this product and any metallic material
located around the product to 100Ωor less.
(2)Keep product wiring away from high voltage or heavy current.
・Attach the accompanying ferrite core (Type:ZCAT2032-0930 made by
TDK Corp.) around the cables that are connected with the power and
grounding terminals.
・The product does not provide a water-proof structure. Do not use it where
mists are present.
PRECAUTION FOR CORRECT USE
14. Communications performance may be reduced due to mutual interference
if more than one Read/WriteAntenna is installed in the same vicinity.
Refer to the Operating Manual (Cat.No.Z268-E1) and confirm that there is
no mutual interference between Read/Write Antennas.
Status Mean
Green Normal
Red Serious malfunction
Slight malfunction
Unlit Power off
Red(blinking)
Status Mean
GreenConnectedto network/Transferring FL Remote IO
Green(blinking)Connectedto network/No transferring FL Remote IO
Green andRed(blinking)
Connected to network/Setting error
RedDuplicate node address
Red(blinking) Not connected to network
UnlitNot connected to network
Status Mean
YellowCommunicating to RF Tag
Unlit Standby
Status Mean
GreenCommunication nomal finish
RedCommunication error
Unlit standby
(1)Status indicator
DEV(Device status indication)
RMT(Remote statusindication)
T/R
NORMAL/ERROR
Status Mean
Green Indicate communicating data contents
Red Indicate error code
Unlit standby
DATA/ERC
(1)Statusindicator
DEV:Device status
RMT:Remote status
T/R:Transmission status
NORMAL/ERROR:Communication status
(2)Data indicator (2colored LED)
DATA:DATAcode(Green)
ERC:Error code (Red)
(3)Mode Switch (Rotary switch3)
regulates function mode
(4)Node Address Switch (rotary switch1,2)
node address setting (01〜64)
(5)FL remote connector
Connect to the FL Remote Master Unit
(6)Power terminal
Use wire size of AWG 12-22 with strip length of
10 mm,and use an isolated 24VDC power source
for supply circuit. Recommended source is
S8VS-03024 (OMRON).
(7)Antenna connector
For connecting model V680-HS63-SP
Name and functions
24V
GND
GR
(2)Data indicator
Error code
LED Description
Cannot detect RF tagin trigger mode.
Cannot communicate with RF tagin trigger mode.
The address outside the memory area of RF tag was specified.
The protectedmemory area of RF tag was specified.
The data could not be written in RF tag.
The RF tag of off the subject was used.
The RF tag of off the subject was used.
The mistake is found inthe instruction of the excution command.
or the FL remote ID cannot recieve the execution specification command.
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
The setting ofthe mode switch isabnormal.
Bit 0 and Bit4
Bit7to Bit 0 FL remote ID cannot work.Bit7to Bit 0
(3)Mode Switch
Name Mean
Trigger modeWhen the trigger signal is input from the plc, FL REMOTE ID begins the
communication with the ID tag, and outputs the communication result tothe plc.
Auto mode When the ID tag approachesthe antenna front, FL REMOTE ID begins the
communication with the ID tag, and outputs the communication result tothe plc.
Test mode FL REMOTE ID repeatedlyexecutesthe ID Tag read of 4 bytes from
00 addresses without the control from the plc
mode error
0
1
2
other
No.
Noise mode The noise environment in the antenna surroundingscan be measured while
disconnected from the Master Unit.
3
E-paper label For e-paper label developed by TOPPAN FORMS co.,ltd. the data can be read
from and written to displayed information can be rewritten.
4mode
Frequency
Radiated magnetic
field strength
13,56MHz
maximum 20 dBμA/m at 10 meters
Suitability for Use
s
Omron Companies shall not be responsible for conformity with any standards,
codes or regulations which apply to the combination of the Product in the
Buyer’s application or use of the Product. At Buyer’s request, Omron will
provide applicable third party certification documents identifying ratings and
limitations of use which apply to the Product. This information by itself is not
sufficient for a complete determination of the suitability of the Product in
combination with the end product, machine, system, or other application or
use. Buyer shall be solely responsible for determining appropriateness of the
particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FORAN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TOADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL
EQUIPMENT OR SYSTEM.
See also Product catalog for Warranty and Limitation of Liability.
Oct, 2014
D
OMRON Corporation Industrial Automation Company
Contact: www.ia.omron.com
Tokyo, JAPAN
OMRON ELECTRONICS LLC
2895 Greenspoint Parkway, Suite 200
Hoffman Estates, IL 60169 U.S.A.
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
No. 438AAlexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark,
Singapore 119967
Tel: (65) 6835-3011/Fax: (65) 6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
OMRON EUROPE B.V.
Sensor Business Unit
Carl-Benz-Str. 4, D-71154 Nufringen, Germany
Tel: (49) 7032-811-0/Fax: (49) 7032-811-199
Regional Headquarters
© OMRON Corporation 2007 All Rights Reserved.
Manufacturer:
Omron Corporation,
Shiokoji Horikawa, Shimogyo-ku,
Kyoto 600-8530 JAPAN
TRACEABILITY INFORMATION:
Importer in EU :
Omron Europe B.V.
Wegalaan 67-69
2132 JD Hoofddorp,
The Netherlands
