OmySalon ESB-B User manual

NOTICE: Thanks for your purchase. We hope you love it! If you enjoyed your shopping experience,
tell us (and others) about it! You could post an online review. This helps us to continue providing
great products. Thanks in advance!If anything we could do better, kindly email us and we’ll try hard
to solve the issue for you.Email: [email protected](Please kindly provide order number when you
contact us.)
SAFETY
To reduce risk of injury when assembling & using the chair, follow these precautions:
OmySalon Electric Beauty Bed with Stool
ATTENTION! PLEASE READ THESE INSTRUCTIONS BEFORE USING THIS DEVICE
• Read all of these instructions before assembling and using your salon chair.
• It is helpful to have 2 people assemble and turn the chair upright after assembling.
• Do not over-extend the chair(0~150kg), creating the risk of falls or tipping the
chair, and its occupant over, resulting in injury
OTHER ITEMS YOU WILL NEED (not included)
• Hand Tools:Wrench,Rubber Mallet,Screwdriver (Phillips),Sturdy
box
Model:ESB-B
PRODUCT
MANUAL

PARTS & FEATURES
Bracket
Bracket support
short Long bar
Seat cushion
Backrest
Handrest
Control board
Transformer
Power plug
2

Installation instruction
First：Install 4 Bracket
supports to Bracket
Parts needed :Bracket + 4
Bracket supports
Step 1 . Match the 4 Bracket
supports with 4 holes of the
Bracket and tighten them.
Second：Assemble
Control board 、
Transformer and Power
plug
• Parts Needed: Control
board + Transformer + Power
plug
Step 1. Assemble Control
board 、Transformer and
Power plug to the push rod .
please see diagram beside
Bracket support
Bracket
Control board
Transformer
Power
push rod
3

Third：Asemmble
Backrest to Seat cushion
Fourth：Install handrests
to Installed seat cushion &
backrest
• Parts Needed: Seat cushion
+ Backrest
Step 1. remove 4 bolts which
fixed on the backrest
Step 2.Match the metal
joining parts of seat cushion
with 4 holes of the backrest
Step 3.Use 4 bolts to tighten
by wrench, please see
diagram beside
• Parts Needed: Installed
Seat cushion & backrest + 2
Handrests
1：Put the installed seat
cushion & backrest up right
2: Insert two handrests into
the holes on each side of the
installed seat cushion &
backrest , please follow up
the diagram beside
Bolt
Backrest
Seat cushion
Installed Seat cushion & backrest
Handrest
4

Sixth：Install cushion
support to the chair
• Parts Needed: Short bar
Step1. Remove the clevis pin
and cotter pin which pre-fixed
in the U-shaped part of seat
cushion and remove the small
bolt which pre-fixed in middle of
the Short bar .
Step 2 .Insert the Short bar
through the hole of the T-bar
which Installed to the bracket to
the U-shaped part of seat
cushion and match the hole of
the Short bar with the 2 holes of
the U-shaped part of seat
cushion, then insert the clevis
pin through the 3 holes and use
the cotter pin to lock it .
Step 3.Insert the small bolt into
the hole which in middle of
Short bar and tighten it .
please follow up the diagram
Fifth：Install seat cushion
to bracket
• Parts Needed: Installed
Seat cushion & Backrest +
Installed bracket & bracket
supports
Step1. Remove 4 bolts and
4 washers which pre-fixed
on the seat cushion
Step 2.Match 4 holes of the
seat cushion with 4 holes of
the bracket and then insert 4
the bolts through 4 washers
and bracket into the 4 holes
of seat cushion, tighten by
wrench , please follow up the
diagram beside
Seat cushion
Bracket
Bolt
washer
Short bar
clevis pin
cotter pin
T-bar
5

Seventh：Install backrest
support to the chair
Parts Needed: Long bar
Step1. Remove the clevis pin
and cotter pin which pre-fixed
in the U-shaped part of
backrest and remove the small
bolt of the Long bar .
Step 2 .Insert the Long bar
through the hole of the T-bar
which Installed to the bracket
into the U-shaped part of
backrest and match the hole of
the Long bar with the 2 holes of
the U-shaped part of backrest
,then insert the clevis pin
through the 3 holes and use the
cotter pin to lock .
Step 3.Insert the small bolt into
the hole of Long bar and tighten
it , please follow up the diagram
beside
Long bar
cotter pin
clevis pin
T-
6

Raising and Lowering the
Chair
• Connect Power plug to
power
• Press the up button to raise
the chair to the desired height
and Press the down button to
lower the chair to the desired
height .
• Do not over-extend the
chair(0~150kg), creating the
risk of falls or tipping the
chair and its occupant over,
resulting in injury
Recline the Backrest
• Adjust the T-bar and
backrest support to allow
Backrest to raise up or down
while the occupant leans
back.
• Adjust the T-bar and
cushion support to allow the
seat cushion to raise up or
down
OPERATING THE CHAIR
Down Button
Up button
Power plug
Transformer
7