OmySalon FESB-W User manual

• Hand Tools:Wrench,Rubber Mallet,Screwdriver (Phillips),Sturdy
OmySalon Electric Beauty Bed
OTHER ITEMS YOU WILL NEED (not included)
box
Model: FESB-W
SAFETY
To reduce risk of injury when assembling & using the chair, follow these
precautions:
Visit our website：www.omysalon.com
For missing parts or questions：email us at [e-mail]
OmySalon Electric Beauty Bed with Stool
• Read all of these instructions before assembling and using your salon chair.
• It is helpful to have 2 people assemble and turn the chair upright after
assembling.
• Do not over-extend the chair(0~150kg), creating the risk of falls or tipping the
chair, and its occupant over, resulting in injury

PARTS & FEATURES
A
B
with red point C
with yellow point
D
E
H
J
K
N
L
M
O
P
Q
R
I
S
Fx4
G
2

PARTS & FEATURES
1
12x14 Open end wrench x1
7
M8x45 bolt x2
2
14x17 Open end wrench x1
8
gasket x8
3
6 mm wrench x1
9
M8x40 bolt x4
4
5 mm wrench x1
10
M10x45 bolt x4
5
M10x65 bolt x4
11
cable ties x3
6
M8x65 bolt x2
12
Foot column x4
3

Installation instruction
First：Install H to G
Step 1: First install F on G
Step 2: Fix H to G with 4 bolts
Step 3: Remove the bolts
pre-installed on the motor
Step 4: Connect A and H to G
Please follow the chart on
the side
Second: install I to H
Step 1: Fix I to H with 4 bolts
Step 2: Remove the bolts
preinstalled on the motor
Step 3: Install B and C to I
Please follow the chart on
the side
H
A
C
F
M10X65 bolt
G
M10X45 bolt
H
I
Pay attention to the direction of motor installation
Pay attention to the direction of motor installation
B
Red Point
Yellow Point
4

Third: install N
Step 1: Remove the
preinstalled pins and cotter
pins
Step 2: Install the backrest
Please follow the chart on
the side
Fourth: install Q and R
Step 1： remove the
preinstalled bolts of N
Step 2: Install Q and R on N
Step 3: Remove the bolts
preinstalled on the motor
Step 4: Connect Q and B
Please follow the table on
the side
N
Cotter pin
pin
Note: pin shaft is installed on one side first and then on the other side,
which is convenient for installation
N
Q
B
R
Red Point
5

Fifth: install L
Step 1: Remove the pre-installed
pins and cotter pins
Step 2: Install L
Step 3: Remove the motor
premounting bolts
Step 4: Connect the motor to the
iron piece on L
Please follow the chart on the
side
Sixth: install side panels
Step 1: Install K, J on I
Please follow the chart on the
side
,
Note: pin shaft is installed on one side first and then on the other side
which is convenient for installation
L
Motor air rod extension,
sofa installation is
convenient
Cotter pin
pin
M8x40 bolt
K
J
I
gasket
CYellow Point
6

Seventh: Install M
Please follow the chart on the
side
Eighth: Install handrails
Please follow the chart on the
side
M
O
P
M8x65 bolt
M8x45 bolt
gasket
gasket
S
7

OPERATING THE CHAIR
Lift the chair
• Connect the power plug to the
power supply
• Press the Up button to lift
Press the button to lower the
chair to the desired height.
• Don't overstretch your chair. A
person should not weigh more
than 150kg, otherwise there is a
risk of falling or tipping the chair
and user, resulting in injury
Backrest leg adjustment
• Adjust the handle button so
that the backrest can be raised
or lowered.
• Adjust handle buttons to block
leg lift.
"
C
B
E
A
N
L
D
A The motor
C The motor
B The motor
Yellow Point
Red Point
8