ON Semiconductor MT9V117 User manual

©Semiconductor Components Industries, LLC, 2016
July, 2016 −Rev. 0
1Publication Order Number:
EVBUM2467/D
MT9V117PACSTCH-GEVB
MT9V117 Evaluation Board
User's Manual
Evaluation Board Overview
The evaluation boards are designed to demonstrate the features of
ON Semiconductor’s image sensors products. This headboard is
intended to plug directly into the Demo 2X system. Test points and
jumpers on the board provide access to clock, I/Os and other
miscellaneous signals.
Features
•Clock Input
♦Default −54 MHz crystal oscillator
♦Optional Demo 2X controlled MClk
•Two Wire Serial Interface
♦Selectable base address
•Parallel Interface
•ROHS Compliant
Block Diagram
Figure 2. Block Diagram of MT9V117PACSTCH−GEVB
MT9T117
OSC
STANDBY
SAADR
CLKN
ON Semiconductor
Demo 2
Power
Supply
+3.3 V
+2.8 V/+1.8 V
+1.8 V
+5.0 V
IMG_OUT
DOUT
RS232 RJ11
Reset
Supervisor
+2.8 V
+1.8 V
+1.8 V +2.8 V/+1.8 V
SYSRST_L
RST_L
D_RST_L
ON Semi
Demo 2
LSB[1:0]
RESET_N
JTAG
JTAG JTAG
SADDR
CLK
I2C ON Semi Demo 2
I2C
AND
Gate
JTAG_RST_L
www.onsemi.com
EVAL BOARD USER’S MANUAL
Figure 1. MT9V117 Evaluation Board

MT9V117PACSTCH−GEVB
www.onsemi.com
2
Top View
Figure 3. Top View of Evaluation Board −Default Jumpers
UART Control JP9
ON_LED JP6
Configuration Switch SW2
+1V8_VDD JP3
+2V8_VAA JP1
Parallel O/P P6
ATEST JP8
RESET Switch SW1
+VDDIO_SEL JP4
+VDDIO JP5
EEPROM ADDR SW3
+VAAPIX JP2
CLK_SELECT JP7
Bottom View
Figure 4. Bottom View of the Evaluation Board −Connector
Baseboard Connector P2

MT9V117PACSTCH−GEVB
www.onsemi.com
3
Jumper Pin Locations
The jumpers on headboards start with Pin 1 on the leftmost
side of the pin. Grouped jumpers increase in pin size with
each jumper added.
Figure 5. Pin Locations for a Single Jumper.
Pin 1 is Located at the Leftmost Side and Increases as it Moves to the Right
Pin 1 Pins 1−4
Figure 6. Pin Locations and Assignments of Grouped Jumpers.
Pin 1 is Located at the Top-Left Corner and Increases in a Zigzag Fashion Shown in the Picture
Pins 1 and 2
Pins 3 and 4
Pins 5 and 6
Pins 7 and 8
Pins 9 and 10
Pin 1
Figure 7. Switches of Configuration Switch SW2 in Their Default Positions.
SAADR (SW2.1), OE_N (SW2.2), and TRST_N (SW2.3) are All OFF by Default
SW2.1
SW2.2
SW2.3
Figure 8. Address Switch Locations in their Default Positions.
The First Switch (ADR0) and the Second Switch (ADR1) of SW3 are Set to ON
A0
A1
A2
WP
Jumper/Header Functions & Default Positions
Table 1. JUMPERS AND HEADERS
Jumper/Header No. Jumper/Header Name Pins Description
JP1 +2V8_VAA 1−2 (Default) Connects to on-board +2V8_VAA power supply
2−3External power supply connection
JP2 +VAAPIX 1−2 (Default) Connects to on-board +VAAPIX power supply
2−3External power supply connection

MT9V117PACSTCH−GEVB
www.onsemi.com
4
Table 1. JUMPERS AND HEADERS (continued)
Jumper/Header No. DescriptionPinsJumper/Header Name
JP3 +1V8_VDD 1−2 (Default) Connects to on-board +1V8_VDD power supply
2−3External power supply connection
JP4 +VDDIO_SEL 1−2 (Default) Sets +VDDIO to 2.8 V
2−3Sets +VDDIO to 1.8 V
JP5 +VDDIO 1−2 (Default) Connection to on-board +VDDIO power supply
2−3External power supply connection
JP6 ON_LED 1−2 (Default) Connects LED to indicate power on
JP7 CLK_SELECT 1−2 (Default) Connects to on-board 54 MHz oscillator
2−3Connects to XMCLK from Demo 2X board
JP8 ATEST Open (Default) For Debug/Test
JP9 UART Control Open (Default) UART shutdown (Tri-State)
1−2UART active
SW1 RESET N/A When pushed, 400 ms reset signal will be sent to MT9V117
SW2 Configuration Switch SW2.1 ON (Default) I2C address set to 0x90
SW2.1 OFF I2C address set to 0xBA
SW2.2 ON (Default) Normal Operation
SW2.2 OFF Tri-State Output
SW2.3 ON (Default) Normal Operation
SW2.3 OFF JTAG Mode
SW3 EEPROM ADDR A2 ON, A1 ON,
A2 OFF, WP ON
(Default)
EEPROM Address set to 0xA8
A0 OFF, A1 OFF,
A2 OFF, WP ON
EEPROM Address set to 0xAC
A0 ON, A1 OFF,
A2 ON, WP ON
EEPROM Address set to 0xA4
A0 ON, A1 ON,
A2 ON, WP ON
EEPROM Address set to 0xA0
Interfacing to ON Semiconductor Demo 2X Baseboard
The ON Semiconductor Demo 2X baseboard has
a similar 26-pin connector which mates with P2 of the
headboard. The four mounting holes secure the baseboard
and the headboard with spacers and screws.

www.onsemi.com
1
onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A
listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
The evaluation board/kit (research and development board/kit) (hereinafter the “board”) is not a finished product and is not available for sale to consumers. The board is only intended
for research, development, demonstration and evaluation purposes and will only be used in laboratory/development areas by persons with an engineering/technical training and familiar
with the risks associated with handling electrical/mechanical components, systems and subsystems. This person assumes full responsibility/liability for proper and safe handling. Any
other use, resale or redistribution for any other purpose is strictly prohibited.
THE BOARD IS PROVIDED BY ONSEMI TO YOU “AS IS” AND WITHOUT ANY REPRESENTATIONS OR WARRANTIES WHATSOEVER. WITHOUT LIMITING THE FOREGOING,
ONSEMI (AND ITS LICENSORS/SUPPLIERS) HEREBY DISCLAIMS ANY AND ALL REPRESENTATIONS AND WARRANTIES IN RELATION TO THE BOARD, ANY
MODIFICATIONS, OR THIS AGREEMENT, WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING WITHOUT LIMITATION ANY AND ALL
REPRESENTATIONS AND WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, NON−INFRINGEMENT, AND THOSE ARISING FROM A
COURSE OF DEALING, TRADE USAGE, TRADE CUSTOM OR TRADE PRACTICE.
onsemi reserves the right to make changes without further notice to any board.
You are responsible for determining whether the board will be suitable for your intended use or application or will achieve your intended results. Prior to using or distributing any systems
that have been evaluated, designed or tested using the board, you agree to test and validate your design to confirm the functionality for your application. Any technical, applications or
design information or advice, quality characterization, reliability data or other services provided by onsemi shall not constitute any representation or warranty by onsemi, and no additional
obligations or liabilities shall arise from onsemi having provided such information or services.
onsemi products including the boards are not designed, intended, or authorized for use in life support systems, or any FDA Class 3 medical devices or medical devices with a similar
or equivalent classification in a foreign jurisdiction, or any devices intended for implantation in the human body. You agree to indemnify, defend and hold harmless onsemi, its directors,
officers, employees, representatives, agents, subsidiaries, affiliates, distributors, and assigns, against any and all liabilities, losses, costs, damages, judgments, and expenses, arising
out of any claim, demand, investigation, lawsuit, regulatory action or cause of action arising out of or associated with any unauthorized use, even if such claim alleges that onsemi was
negligent regarding the design or manufacture of any products and/or the board.
This evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC,
CE or UL, and may not meet the technical requirements of these or other related directives.
FCC WARNING – This evaluation board/kit is intended for use for engineering development, demonstration, or evaluation purposes only and is not considered by onsemi to be a finished
end product fit for general consumer use. It may generate, use, or radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant
to part 15 of FCC rules, which are designed to provide reasonable protection against radio frequency interference. Operation of this equipment may cause interference with radio
communications, in which case the user shall be responsible, at its expense, to take whatever measures may be required to correct this interference.
onsemi does not convey any license under its patent rights nor the rights of others.
LIMITATIONS OF LIABILITY: onsemi shall not be liable for any special, consequential, incidental, indirect or punitive damages, including, but not limited to the costs of requalification,
delay, loss of profits or goodwill, arising out of or in connection with the board, even if onsemi is advised of the possibility of such damages. In no event shall onsemi’s aggregate liability
from any obligation arising out of or in connection with the board, under any theory of liability, exceed the purchase price paid for the board, if any.
The board is provided to you subject to the license and other terms per onsemi’s standard terms and conditions of sale. For more information and documentation, please visit
www.onsemi.com.
PUBLICATION ORDERING INFORMATION
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: [phone]
LITERATURE FULFILLMENT:
Email Requests to: [email protected]
onsemi Website: www.onsemi.com
Europe, Middle East and Africa Technical Support:
Phone: [phone]
For additional information, please contact your local Sales Representative
◊

Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
onsemi:
MT9V117PACSTCH-GEVB