on stage KS7365-EJ User manual

KS7365-EJ
ASSEMBLY INSTRUCTIONS
Congratulations on your purchase of the KS7365EJ Pro Heavy-Duty Folding-Z Keyboard
Stand with Second Tier. The model that you purchased was designed with input from
major keyboard performers and keyboard technicians. To fully utilize the strength of
this stand, please read the following assembly instructions carefully. We hope you
enjoy your new purchase!
PREPARATION
Remove the three locked pieces from the box (see photo to the right).
(IMPORTANT TIP: These 3 pieces can be reattached for transport.
Study photo and note their relationship to one another.) Remove
the 2 knobs (E) that are located at the cross bar and set them aside.
Remove the telescoping box beam (B) from the two Folding-Z legs (A)
and set the three pieces aside.
REMOVE REMAINING PARTS FROM THE BOX
AND IDENTIFY ALL THE PARTS:
(A) 2--Folding Z-Leg assemblies
(B) 1--Telescoping box beam
(C) 2--Adjustment knobs with bullet-nose ends
(D) 8--Foam pad strips
(E) 2--Box beam knobs with 1 ¼" threaded bolts
(F) 2--Second tier arm assemblies
(F1) 2--Second tier rotation adjustment knobs
(Factory Installed)
(F2) 2--Second tier rotation adjustment knobs
(Factory Installed)
(G) 1--Support bar for second tier
(H) 2--Locking knobs with 3/8" threaded bolts
Assemble the Folding Z-Leg Assembly
1. Hold one of the Folding Z-Legs (A) upright and rotate the feet until they
lock in the U-shaped bracket. Repeat this procedure to the support arm.
[Tip: To unlock the arms and feet for storage or transport, depress
the chrome button and move the arm in the opposing direction.]
2. Thread one of the adjustment knobs with bullet-nose end (C) into the
welded nut on the lower Folding-Z leg. Pull out the telescoping upper leg
until any of the line-it-up markers lines up with the top edge of the lower
leg opening. Turn the knob clockwise until it locks in place.
3. Repeat this procedure on the other Folding-Z leg.
B
A
C
D
E
F
H
G
OPEN
FOLDED
Only one of each set of
parts may be identified
in the above illustration.
B
A
E
A
C
F1

© 2003 TMP, Inc.
www.musicpeopleinc.com
www.onstagestands.com
Assemble the Box Beam to the Folding-Z Legs
Be sure the round welded nut on the lower Folding-Z leg faces the
inside of the stand. Take the box beam (B) and thread knobs (E) into
the 2 Folding-Z legs (A) until secured in place.
[Tip: The knobs on the box beam should face the same direction
as the knobs on the Folding-Z legs for ease of set-up and
tear-down.]
Adding the Second Tier to the Folding-Z Base
1. Loosen the 2" knob (F2). Pull out the telescoping upper arm until any of the line-it-
up markers lines up with the top edge of the lower arm opening. Tighten knob (F2).
Loosen the rotation adjustment knob (F1) and rotate the arm to a 45-90° angle.
Tighten Knob (F1).
2. Insert the second tier U-shaped channel
into the opening in front end of the main
support arm. Make sure the rotation
adjustment knob (F1) is facing the outside of
the stand, and that the welded nut on the
inside of the U-shaped channel is facing 
the inside of the stand. Once the U-shaped
channel is fully inserted, use knob (H) to
secure the second tier to the base unit.
3. Repeat this same procedure on the other
second tier support arm
4. Place the support bar (G) so the telescoping adjustment knob is facing away from
the second tier support arms. Remove the knobs from the ends of the support bar,
position the support bar on the second tier support arms and reinstall the knobs.
Apply the Foam Padding
1. Open the box beam to the desired width to hold your main keyboard and tighten
the adjustment knobs.
2. Place the keyboard on the stand and mark the front and back of the support arms
where the pads should be placed. Remove the keyboard. Peel off the backing of the
foam pad strips (D) and press the pads into position.
3. Repeat this procedure on the second tier.
E
F1
F2
G
Opposite
angle
H
B
A