One Lux MWS008S/H User manual

Microwave Motion Sensor – Basic Version
One-LUX Limited
South Staffs Freight Terminal,
Lynn Lane, Lichfield,
WS14 0ED. UK
t: [phone]
f: [phone]
e: [e-mail]
w: www.One-LUX.com
MWS008S/H

Product Specification
PRODUCT TYPE: Microwave Motion Sensor
OPERATING VOLTAGE: 220/240V ~ 50Hz/60Hz
HF SYSTEM: 5.8GHz CW radar
TRANSMISSION POWER: <1mW
RATED LOAD: 800W (resistive load)
400W (inductive load)
DETECTION ANGLE: 30~150°
POWER CONSUMPTION: Approx 0.9W
REACH: 1-5m (radius), adjustable
TIME SETTING: 5s ~ 25 min.
MOUNTING: Indoor ceiling and wall mounting
LIGHT CONTROL: 2 ~ 30LUX adjustable
Technical Specifications
2.
Model no.: MWS008S/H
INTRODUCTION
The sensor is an active motion detector; it emits a high-frequency electro-magnetic wave 5.8GHz and receives its
echo. The sensor detects the change in echo from movement in its detection zone. A microprocessor then triggers the
switch light ON command. Movement detection is possible through doors, panels of glass or thin walls.
Note: the high-frequency output of this sensor is <1mW; approximately just 0.1% of the transmission power of a mobile telephone or the output of a microwave oven.
Motion-PHASE FUNCTION
The One-LUX Motion-PHASE Function allows energy saving without compromising comfort or security.
When used in conjunction with a One-LUX dimmable ballast, Motion-PHASE Function delivers optimum energy
savings.
It is perfect for use in corridors, stairwells and underground passageways where low light levels are maintained until
motion is detected.
Never be left in the dark with One-LUX Motion-PHASE.
Wiring & Setting Instructions
INSTALLATION & WIRING
Ensure that the electricity supply is switched off completely before installing or servicing this product.
The sensor works with a mains voltage of 220-240V (+/-10%) 50/60 Hz.
A 100-120V version is available to order.
The sensor has a 3-wire electrical input:
•N (neutral / 230 V AC)
• L (phase / 230 V AC)
•L’ (switched phase / output)
Adjustable Detection Area
Hold Time
Daylight Threshold
Antenna Module
No Motion Detected
Motion Detected
Power SupplyDaylight Sensor 220 - 240V Output Control

3.
Product Specification
Wiring & Setting Instructions
Model no.: MWS008S/H
To connect several standard ballasts with 1 sensor (ON-OFF function), the wiring should be:
N
L
~220-240VAC
To connect several dimmable ballasts with one sensor, the wiring should follow the below schematic:
N
L
~220-240VAC

4.
Product Specification
Wiring & Setting Instructions
Model no.: MWS008S/H
SETTINGS
Detection Sensitivity:
This determines the effective range of the motion
detector and is set by DIP switches on the sensor itself.
Note that reducing the sensitivity will also narrow the
detection range.
The following settings are available:
I - maximum range up to 5m
II - range up to 3.5m
III - range up to 2m
IV - range up to 1.5m
V - range up to 1m
Hold time:
This determines the length of time the lamp is held on
after movement is detected and is set by DIP switches.
The walk test setting is useful when installing the fitting
to establish correct operation and range.
The following settings are available:
I - Walk test mode 5s
II - 30s
III - 3 minutes
IV - 5 minutes
V - 15 minutes
VI - 25 minutes
Daylight Sensor:
This setting holds the lamp off should there be sufficient
daylight and is set using DIP switches on the sensor.
The following settings are available:
I - 2 lux darkness operation only
II - 5 lux darkness operation only
III - 20 lux twilight operation
IV - 30 lux twilight operation
V - daylight, daylight sensor disabled