One Lux ONE-SENSE EXO User manual

Issue C
1
MICROWAVE MOTION SENSOR USER GUIDE
Model No.: OS/ EXO
Model: OS EXO Dimensions (mm)
Technical Specifications
Input voltage
220/240Vac 50Hz
TUV
Rated load
400W(Inductive load), 800W(Resistive load)
Detection area
0.5m ~ 8m, adjustable.
Hold time
10sec / 30sec / 90sec / 3min / 20min / 30min.
Daylight sensor
5 lux / 10 lux / 30 lux / 50 lux / Disable. (Typical)
Sensor principle
Microwave motion detector
Microwave frequency
5.8GHz±75Hz, ISM wave band
Transmitting power
<0.5mW (1% of transmitting power for cell phone)
Detection range
Max. (Ф x h): 16m x 6m.
Detection angle
150° (Wall installation)
360° (Ceiling installation)
Motion detection
0.5 ~ 3m/s.
Operating temperature
-20°C - 60°C
IP rating
IP20
General Guidelines for Installation
1, Specifications for detection area, detection range and daylight sensor levels are typical, so
suitability should be determined for sensitive applications.
2, The Motion sensor should be installed by a qualified electrician. Ensure the electricity supply is
switched off before installing or servicing the product.
3, The sensor should not be modified in any way. Any modifications mode to this product will
immediately invalidate any warranties issued.
4, The company does not accept responsibility for any consequences resulting from unauthorized
modification of the product.
5, The sensor should be connected to a stable power supply of 220/240Vac 50Hz.
6, Microwaves cannot pass through metal or brick walls if thicker than 20cm. They will pass through
thinner walls but there will be some attenuation.
7, Installation inside a glass or plastic housing will result in a reduction of detection sensitivity.
Expect a reduction of approximately 20% for every 3mm of thickness.
Installation & Wiring
The sensor is designed for installation at 1~6m in height.
Suggested mounting height:
1~1.8m (Wall mounting)
2.5~6m (Ceiling mounting)
Note: L(BLACK) , N(BLUE) ,L’(BROWN)

Issue C
2
100H burn-in mode for fluorescent lamps
With simple operation, rapidly turn on/off the power 4 times within 4 seconds. Lamps will be 100% on for 100
hours and then automatically revert to sensor mode. This is crucial to secure the lifetime of fluorescent
lamps when a new fixture is installed or an old lamp is replaced. This 100H burn-in feature can be cancelled
by turning off the power.
Detection Pattern
Settings
Detection area, hold time and daylight sensor can be set using DIP switches on the sensor. Note that
reducing the detection area will also reduce the sensitivity.
1, Sensitivity
Refers to the typical detection range sensitivity. 100% being most sensitive.
I: 100% - Up to 8m
II: 75% - Up to 6m
III: 50% - Up to 4m
IV: 25% - Up to 3m
V: 10% - Up to 2m
2, On time
Refers to the time period the lamp remains at 100% illumination after no motion detected.
I: 10 sec
II: 30 sec
III: 90 sec
IV: 3 min
V: 20 min
VI: 30 min
3, Light sensor
The sensor can be set to only allow the lamp to illuminate below a defined ambient
brightness threshold. Settings are typical and as follows:
Disable*
Max - 50 lux, twilight operation
II - 30 lux, twilight operation
I - 10 lux, darkness operation only
Min -5 lux, darkness operation only
*When set to Disable the daylight sensor will switch on the lamp when motion is detected
regardless of ambient light levels.
Ceiling mounting pattern (Unit: m)
Suggested mounting height: 2.5-6m
Wall mounting pattern (Unit: m)
Suggested mounting height: 1-1.8m

Issue C
3
FAQS
Question
Cause
Remedy
The load will not illuminate.
Incorrect daylight sensor setting selected.
Adjust setting.
Load has failed.
Replace load.
Power is switched off.
Switch on.
The load is permanently
illuminated.
Continuous movement in the detection area.
Check detection area setting.
The lamp (containing sensor) is installed in
an area too close to reflective surfaces, i.e.
metal, glass or concrete walls.
1, Make sure installation area suitable
with at least 30cm space between lamp
and surrounding reflective surfaces.
2, Reduce sensitivity (detection area).
The load will not illuminate
despite movement.
Speed of moving object is not in the range of
0.5-3m/s or the detection radius is too small.
Check detection area setting.
www.One-LUX.com