Oneida Air Systems AXD000002-HD-5 User manual

2” Heavy Duty
Dust Deputy Deluxe
#AXD000002-HD-5
#AXD000002-HD-5KIT
Doc. #ZBI000020
Appearance may vary slightly
U.S. Patent: #RE40048E1
U.S. Patent: #7282074B1
U.S. Patent: #6833016B2
U.S. Patent: #7282074C1
August 28, 2019

2Oneida Air Systems
System Start-Up Information
1. Do not vacuum anything that is burning or smoking, such as cigarettes, matches, hot ashes, or any hot
substance!
2. Do not vacuum (or use this cyclone near) ammable or combustible liquids, gases, or explosive dusts, such as
gasoline or other fuels, lighter uid, cleaners, oil-based paints, natural gas, hydrogen, coal dust, magnesium
dust, grain dust, aluminum dust, sugar dust, our dust or gun powder.
3. To reduce the risk of health hazards from vapors or dusts, do not vacuum toxic materials unless a HEPA lter
is used. Do not use or store near hazardous materials.
4. Dust can be ammable and explosive. Some dust can be toxic or cause allergic reactions.
5. Wood dust mixtures are highly ammable and can be explosive. NEVER introduce sparks or sources of
ignition into collector.
a. Dump drum after each use.
b. Ground system.
6. NEVER leave wood dust in a building or vehicle.
7. Keep re extinguishers handy at all times.
8. Can be used for collecting non-ammable liquids.
9. Dispose of waste in a FIRE SAFE AREA.
READ THE SAFETY PRACTICES INSTALLATION AND MAINTENANCE INSTRUCTIONS AND YOUR
WET/ DRYVACUUM’S OWNER’S MANUAL BEFORE ASSEMBLING AND USINGTHE DUST DEPUTY
SOME DUSTS ARE HIGHLY FLAMMABLE OR EXPLOSIVE. LEARN / KNOW WHAT YOU ARE
DEALING WITH. FOLLOW ALL LOCAL, STATE, FEDERAL & NFPA CODES AND GUIDE LINES.

1Oneida Air Systems
Heavy Duty Dust Deputy Contents
ID Part number Part description Qty
AAXD200036 Raw 2" x 3' Hose 1
B AXD600103 2" Elbow 2
C AXD600104 2" Elbow with 1/4" Fitting 1
D AXD200225 2.0" ID to 2.25" OD Adapter 1
E AXD225225 2.25" ID Connector 2
F VXC110001 Steel Cyclone Separator 1
G AHX000016 Hardware Pack 1
G1 AFS015920 1/4"-20 X 3/4”Bolts 6
G2 AFW025000 1/4" Flat Washer 6
G3 AFT000005 1/4" Flange Nut 6
H AXG000004A Gasket for Cyclone 1
I SEX050399 Steel Lid for 5 Gallon Pail 1
J RGF000012 12" Diameter Gasket for Lid 2
If you cannot find an item on the list examine the packaging materials very carefully. Certain
components may have been pre-installed for shipping purposes. There may be hardware
leftover.

Please unpack the parts carefully and conrm
you have received each item listed here.
You will need the following:
• Tape Measure or Ruler
• 7/16" Wrench
• Power Drill
• 1/2" Drill Bit
ID Part number Part description Qty
K SDS050001 5 Gallon Pail 2
L ACB360000 Turn Key Hose Clamp 2
M AFC270250 2 1/2”Rubber Coupling 1
N AXD600102 1/4" Tube Fitting 1
O AXD600200 1/4" OD Clear Vinyl Tubing 3
P AXD600300 16" X 14" X 36" 1.5 MIL Bag 1
INCLUDED ONLY WITH 5KIT SYSTEMS
Q AHX000019 Mobility Hardware Package 1
Q1 AFJ051602 5/16"-18 X 2" J Bolt 2
Q2 AFT051602 5/16"-18 Square Nut 2
Q3 RHS000010 Rubber Strap with S Cus 2
R SDD990000 Molded Drum Dolly 1

F
E
D
A
C
B
G3
G2
G1
HI
J
K
M
L
N
O
Q1
Q1
Q2
Q2
Q3Q3
R
22oneida-air.com
Heavy Duty Dust Deputy Contents (Continued)

FIG. 2 FIG. 3
FIG. 1
FIG. 3
3Oneida Air Systems
Assembly Instructions
Place Gasket for Cyclone (H) over the center
hole in the Steel Lid (I) and line up the holes.
Secure the Cyclone (F) using the 1/4”-20 X 3/4”
Bolts (G1), 1/4” Flat Washers (G2), and 1/4”
Flange Nuts (G3) from the Hardware Pack (G)
as shown in [FIG. 1]
1
Place the 12" Diameter Gasket (J) over the lip
along the rim of the 5 Gallon Pail (K) as shown
in [FIG 2] & [FIG 3]
NOTE: Double Ribs of gasket are facing up, and
the gasket wraps around lip of drum.
2
3If you wish to use bags, rst install the bag
retainer:
a. Drill a ½" diameter hole about 1-½" from
the bottom edge of the 5 Gallon Pail (K).
b. Screw the 1/4" Tube Fitting (N) into the
newly drilled hole, it will form its own
threads. Carefully and gently, use a wrench
to screw it all the way in, over tightening
will strip the threads.
c. Attach the 2” Elbow with 1/4” Fitting (C) to
the top outlet of the Steel Cyclone. (F)
d. Insert one end of the 1/4” OD Clear Vinyl
Tubing (N) into the 2” Elbow with 1/4”
Fitting (C) and the other end into the tting
at the base of the 5 Gallon Pail (K).
NOTE: Using a bag with the Dust Deputy will
help minimize exposure to trapped dust

FIG. 5
FIG. 6
FIG. 7
44oneida-air.com
Assembly Instructions (Continued)
4Once the bag retainer is installed:
a. Insert Bag (P), into the 5 Gallon Pail (K) so
the bag is fairly snug to the edges.
b. Fold the top edge of the Bag (P) over the
rim of the 5 Gallon Pail (K) neatly to
minimize the folds which will cause leaks.
c. Place the Steel Lid (I) and turn on your
system.
d. When the 5 Gallon Pail (K) is 2/3 full,
remove the Steel Lid (I) and pull out the
Bag (P), seal, and dispose.
5If you wish to use the Mobility Kit (Q):
a. Insert the 5/16"-18 Square Nut (Q2) into
the square pocket on the underside of the
Molded Drum Dolly (R) and a 5/16"-18
X 2" J Bolt (Q1) in the indicated holes on
opposing sides of the Molded Drum Dolly
(R). DO NOT overtighten [FIG. 6].
b. Secure the Rubber Strap with S Cus (Q3)
at their halfway point underneath each J
Bolt (Q1) as shown in [FIG. 6].
c. Place 5 Gallon Pail (K) in center of Molded
Drum Dolly (R), and then place the
assembled unit on top of it
d. Hook the Rubber Straps S Cus (Q3) into
the holes on the Steel Lid (I) in order to
secure the assembled unit to the Molded
Drum Dolly (R)[FIG 7].
WARNING: DO NOT OVERSTRETCH RUBBER
STRAPS

Customer Service Dept.
1-866-387-8822 • [e-mail]
1001 West Fayette Street, Syracuse, NY 13204 U.S.A.
Copyright © 2019 Oneida Air Systems, Inc.
ank you for your business!
Regardless of where you purchased your system, if you have any
questions or issues with missing / damaged parts, please call
Oneida Air Systems rst to let us help resolve your problem.
We fully stand behind the quality of our product and place the
utmost value on our customer’s opinion.
We want to do everything possible to make your purchase and
experience with Oneida Air Systems a good one!