OneTech 2D-STAEXTU User manual

Preface
Dear Users,
Thank you for choosing and using our products.
In order for the better use of the product, please read this manual in
details and operate following the steps. Please also keep this manual
well stored for future reference.
Our company is committed to improve the product functions and service
quality continuously. The contents and figures in this manual may be
different from the actual product. The function description may have
slight differences due to specific types. If there are some differences
between the manual and the actual product, please refer to the actual
product.
Some parts, appearances or functions mentioned in this manual may
contain the copyright issues. No part of this manual may
be reproduced or transmitted in any form or by any means without
prior written consent of our company.
Our company reserves the right to modify the contents and specifications
of this manual. The contents are subject to change without prior notice.
Should you have any question, please contact us and we will be at your
service. Thank you again for your use of our products.
USER MANUAL
2D-STAEXTU

IPPS Intercom System
Catalogue
Chapter I Product Introduction................................1
1.1 Appearance..............................................1
1.2 Basic Function........................................... 3
1.3 Status Indicator..........................................3
1.4 Technical Parameters................................ 3
1.5 Product Standard.......................................3
1.6 Configuration List........................................4
Chapter II Basic Operations...................................... 4
Chapter III Web Settings ........................................ 5
Chapter IV IC Card Registration..............................13
Chapter V System Connection Diagram..................17
Chapter VI Extension Connection Diagram.............18
Chater VII Installation Instructions.............................22
Chapter VIII Safety Instructions...............................28

IPPS Intercom System
-1-
Chapter I
Product Introduction
1.1 Appearance
Type:D-C9
Fill Light
Speaker
Photosensitive Diod
Type:D-C3（with funcion of swiping card）
Photosensitive Diod
Night Light
Label
Speaker
Camera
Emergency Call Key
Microphone
Microphone
Camera
Card Area
Call Key

IPPS Intercom System
-2-
Type:D-C3（with numeric keyboard）
Photosensitive Diod
Night Light
Label
Speaker
Type: D-C3（with one button）
Photosensitive Diod
Night Light
Label
Speaker
Microphone
Camera
Numeric Keyboard
Call Key
Microphone
Camera
Call Key

IPPS Intercom System
-3-
1.2 Basic Function
◇Call the host for video call
◇Receive music broadcat and announcement from the host
◇Be able to connected with external microphone, active loudsperker,
record output,door light control, electric lock,door contact, and alarm
button, etc.
1.3 Status Indicator
◇When enabeling the outer net mode (checking SIP account), when
there is anomalous connection between the extension and the server, the
indicator light flashes slowly.
◇When the network isn’t connected, the indicator light flashes rapidly.
◇During the call, the indicator light flashes rapidly.
◇When the extension is idle, the indicator light keeps flashing.
1.4
Technical Parameters
◇Working Voltage: DC12V
◇Rataed Power: 4W
◇Standby Power: 2W
◇Working Temperature: -20～+55℃
◇Storage Tempeature: -10～+40℃
◇Storage Relative Humidity: 20%～80%
◇IP Rating: IP55(D-C9)
IP54(D-C3)
1.5 Product Standard
◇ GA 1210-2014 Security Technical Requirements for Building
Intercom Systems
◇ GB/T31070.1-2014 Building Intercom Systems—Part 1: General
Technical Requirements
◇ GA/T678-2007 Specifications of Video Intercom Connected Networks
System

IPPS Intercom System
-4-
1.6 Configuration List
Open the packing box to check the configuration list inside the box.
Chapter II Basic Operations
1. Call
Press “Emergency Call Key” to call the host.
2. Unlock by card(only applicable to Type D-C3 with the function of swiping
card)
HoldingtheregisteredICorIDcardclosetothecard area,theextension will
havethebeep and the door is unlocked.
3. Unlock by password（only applicable to Type D-C3 with numeric
keyboard）
In standby mode, input “#+password+#” to unlock the door.
4. View IPAddress
Run “710 System Upgrade Tool” in the computer and Double-click on it
for the following interface:

IPPS Intercom System
-5-
Clicking the icon “Search”, IP address will be shown in the box of IP
address.
Chapter III Web Settings
Connect the extension to the computer by the switch, enter the
extension’s IP address in the web browser of computer (IP addresses of
the computer and the extension should be in the same network
segment), and then enter user name & password (The system default
user is “admin” and the passoword is “123456”) to enter the following
interface:

IPPS Intercom System
-6-
3.1 System Settings
Clicking the icon “System Settings”, the system will enter the following
interface:
The number means the number of this extension with setting range 1~999;
the host number means the number for superior host of this extension.
Call Time: time limit for the call with the host.
Remark: the actual call time is subject to the minimum call time set bytwo
parties.
Code Stream: it depends on current network environment. The code stream
can be adjusted appropriately to ensure the fluency of video.
Call Modes: they can be divided into normal mode, IPdirect call, SIP direct
call and building mode.
①Normal mode: give an ordinary call to the center host;
②IP Direct Call: In the mode of crossing VLAN, enable the mode of IP direct
call. The host’s IP address needs to be input.
③SIPDirect Call: Inputting the account No,can call the corresponding SIP
terminal;
④Building Mode: compatible with the indoor extensions of our digital
products.
Remark: Except for the first item,addresssettingsarerequiredforother three
modes.Ifnorelevantsettingspopup,pleasetryagainwithcompatiblemodeof

IPPS Intercom System
-7-
thebrowser.
After setting, click the icon “Apply”to enable the settings.
3.2 Network Settings
Clicking the icon “Network Settings”, the system will enter the following
interface:
IPAddress: for the same network segment in the same system, IP address
should be different.
Subnet Mask: The original subnet mask is 255.255.255.0. Normally no
change is needed. If the user needs to change it, it can be changed by
inputting directly.
Gateway: It’s input according to the assignement of IP network segment s for
the site.
DNS: It means IPaddress of DNS server.
IPPS Server: IP address of IPPS management platform server
NTP: address of NTPtime server
After setting, click the icon “Apply” to enable the settings.
3.3 SIPSettings
Clicking the icon “SIP Settings”, the system will enter the following interface:

IPPS Intercom System
-8-
Server: URLof SIP proxy server in format of sip:ip or sip: domain name.
Realm: Scope of device, same as IP or domain name in general.
Password: Password for accessing SIP proxy server, provided by the
administrator of SIP proxy server.
Stun Address and Port: IP and port of public server for NAT traversal of
audio and video.
To connect with the SIP internet phone of other factory, check “Enable SIP”
and enter the registration number of SIPserver in “User Name”.
After setting, click the icon “Apply” to enable the settings.
3.4 Volume Settings
Clicking the icon “Volume Settings”, the system will enter the following
interface: