Onkyo W800BT User manual
W800BT
USER
MANUAL
1EN
Contents
Contents
1 Important safety instructions 2
Hearing Safety 2
General information 2
2 Onkyo Bluetooth wireless headset3
Box content 3
Other devices 3
Overview of your Bluetooth wireless
headset 3
3 Charge and pair your headset 4
Charge the battery 4
Pair between both sides of the
headset 5
Pair your headset with the
Bluetooth device 5
4 Use your headset 7
Connect the headset to a Bluetooth
device 7
Operate your headset 7
Wear your headset 8
5 Technical data 9
6 Notice 10
Notice of compliance 10
Disposal of your old product and
battery 10
Trademarks 11
7 Frequently asked questions 12
2EN
1 Important
safety
instructions
Hearing Safety
Danger
• To avoid hearing damage, limit the time you use
headphones at high volume and set the volume to
a safe level. The louder the volume, the shorter the
safe listening time is.
Be sure to observe the following guidelines
when using your headset.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume
continuously upwards as your hearing
adapts.
• Do not turn up the volume so high that
you can’t hear what’s around you.
• You should use caution or temporarily
discontinue use in potentially
hazardous situations.
• Excessive sound pressure from
earphones and headphones can cause
hearing loss.
• Using headphones with both
ears covered while driving is not
recommended and may be illegal in
some areas while driving.
• For your safety, avoid distractions
from music or phone calls while in
trac or other potentially dangerous
environments.
General information
To avoid damage or malfunction:
Caution
• Do not expose the headset to excessive heat.
• Do not drop your headset.
• Headset shall not be exposed to dripping or
splashing.
• Do not allow your headset to be submerged in
water.
• Do not use any cleaning agents containing alcohol,
ammonia, benzene, or abrasives.
• If cleaning is required use a soft cloth, if necessary
dampened with a minimum amount of water or
diluted mild soap, to clean the product.
• The integrated battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
• Risk of explosion if battery is replaced by an
incorrect type. Replace only with the same or
equivalent type.
About operating and storage temperatures
and humidity
• Operate or store in a place where
temperature is between -15ºC (5ºF)
and 55ºC (131ºF) (up to 90% relative
humidity.
• Battery life may be shorter in high or
low temperature conditions.
3EN
2 Onkyo
Bluetooth
wireless
headset
Box content
Onkyo Bluetooth wireless headset W800BT
Replaceable rubber ear caps x 2 pairs
Charging case
Quick start guide
Other devices
A mobile phone or electronic device (e.g.
notebook, PDA, Bluetooth adapters, MP3
players etc) which supports Bluetooth and
is compatible to the headset (see 'Technical
data' on page 6).
Overview of your Bluetooth
wireless headset
1
2
4
5
6
3
7
8
9
a On/o, call control button
b LED indicator
c Microphone
d USB cable (for charging)
e Headset charging socket
f Battery indicator
g Battery indicator button
h LED indicator
i On/o button
4EN
3
Charge and pair
your headset
Charge the battery
Note
• Before you use your headset/charging case for
the first time, charge the battery for 5 hours for
optimum battery capacity and lifetime.
• Use only the original USB charging cable to avoid
any damage.
• Finish your call before charging the headset, as
connecting the headset for charging will power the
headset o.
Charging case
Plug the USB cable into the power source.
The charging case starts charging.
Tip
• Normally, a full charge takes 2 hours.
• When the charging case is charging, the battery
indicator keeps flashing until charging is complete.
There are 5 indicator lights. The leftmost LED light
indicates the charging status. The other 4 LED
lights indicate the battery level. Each LED light
indicated 25% battery. When all 4 LED lights are
turned on and stable, the charging case is fully
charged.
• Press the battery indicator button to show the
battery level status.
5EN
Headset
Place the headset on the charging case.
The headset starts charging.
• When the headset is charging, a white
LED light will be displayed.
• When the headset is fully charged, the
white light goes o.
Tip
• Normally, a full charge takes 70 minutes.
Pair between both sides of
the headset
1 Make sure that the headset is fully
charged.
2 Press and hold the power on/o button
on both sides of the headset for 2
seconds.
The white LED light on the left side
of the headset flashes slowly after
pairing with the right side of the
headset.
The white LED light on the right side
of the headset flashes rapidly. The
headset is ready to pair with the
Bluetooth device.
Pair your headset with the
Bluetooth device
1 Turn on the Bluetooth function of your
mobile phone.
2 Pair the headset with the mobile phone.
For detailed information, refer to the
user manual of your mobile phone.
Tip
• The headset stores the last 4 devices in the
memory. If you try to pair more than 4 devices, the
earliest paired device is replaced by the new one.
6EN
The following example shows you how to
pair the headset with your mobile phone.
1 Activate the Bluetooth feature of your
mobile phone, select Onkyo W800BT.
2 Enter the headset password "0000" (4
zeros) if prompted. For those mobile
phones featuring Bluetooth 3.0 or
higher, no need to enter a password.
Onkyo W800BT
7EN
4 Use your
headset
Connect the headset to a
Bluetooth device
1 Turn on your mobile phone/Bluetooth
device.
2 Press and hold the power on/o button
for 2 seconds on both sides of the
headset.
The white LED light on the left side
of the headset flashes slowly after
pairing with the right side of the
headset.
The white LED light on the right side
of the headset flashes rapidly. The
headset is ready to pair with the
Bluetooth device.
The headset is reconnected
to the last connected mobile
phone/Bluetooth device
automatically.
Tip
• If you turn on the mobile phone/Bluetooth device
or activate the Bluetooth feature after turning on
the headset, you have to reconnect the headset and
mobile phone/Bluetooth device manually.
• If your mobile phone/Bluetooth device cannot
reconnect automatically, try to reconnect
manually by clicking the headset's name again
under the Bluetooth setting menu on your mobile
phone/Bluetooth device.
Note
• If the headset fails to connect to any Bluetooth
device within range in 5 minutes, it will switch o
automatically to save the battery life.
Operate your headset
On/o
Task Button Operation
Turn the
headset
on.
On/o,
call control
Press and hold for
2 seconds.
You hear a
power on
signal tone.
Turn the
headset
o.
on/o,
call control
Press and hold for
4 seconds.
The white
LED is on for
2 seconds
and then the
headset is o.
You hear a
power o
signal tone.
Call control
Task Button (right
headset)
Operation
Pick
up/hang
up a call.
On/o,
call control
Press once.
Reject an
incoming
call.
On/o,
call control
Press and
hold for 2
seconds.
8EN
LED indicator status
Headset
status
Right side of
the headset
Left side of the
headset
O/Charging
is complete.
O O
Unconnected
between
both sides of
the headset.
N/A The blue LED
flashes slowly.
Ready for
pairing
between
both sides of
the headset.
The blue
and white
LEDs flashes
rapidly.
The blue and
white LEDs
flashes rapidly.
Pairing
with the
Bluetooth
device.
The white LED
light flashes
rapidly.
N/A
Paired and
ready to use.
The white LED
light flashes
slowly
One short
beep.
The white LED
light flashes
slowly.
During
music
playback.
The blue LED
flashes slowly.
The blue LED
flashes slowly.
When
there is an
incoming
call.
The blue and
white LEDs
flashes slowly
The white LED
flashes slowly.
In a call. The blue LED
is on.
The white LED
flashes slowly.
Charging is
in progress.
The white LED
is on.
The white LED
is on.
Low battery
level.
The white
LED light
flashes twice
for every 10
seconds.
Low
battery
signal tone
for every
minute.
The blue and
white LEDs
flashes rapidly.
Wear your headset
1 Push your headset inward and rotate it
forward to ensure the winglet is nested
inside the cavity above the ear canal.
2 Rotate your headset forward and
backward accordingly for the best
personal fit.
9EN
5 Technical data
Headset
• Play time: up to 3 hrs (up to 15 hrs with
charging case)
• Standby time: 40 hrs (up to 200 hrs
with charging case)
• Charging Time: 70 mins
• Rechargeable Li-ion battery: 55mAh
• Bluetooth 4.1, Bluetooth mono support
(Headset profile - HSP, Hands-Free
Profile - HFP), Bluetooth stereo
supported (Advanced Audio Distribution
Profile - A2DP)
• Operating range : Up to 10 meters (33
feet)
• Digital noise and echo reduction
• Auto power o
Charging case
• Charging time: 2hrs
• Rechargeable Li-ion battery : 900mAh
• Number of recharges supported: 5
Note
• Specifications are subject to change without notice.
10
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be
installed and operated with a minimum
distance of 20cm between the radiator and
your body. This transmitter must not be co-
located or operated in conjunction with any
other antenna or transmitter.
Warning: Changes or modifications made
to this equipment not expressly approved
by Gibson Innovations may void the FCC
authorization to operate this equipment.
Model number: W800BT
Trade Name: Onkyo
Responsible party: Gibson Innovations USA
Inc.3070 Windward Plaza Suite F, Box 735
Alpharetta, GA 30005
Notice for Canada:
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1) this device may not cause harmful
interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
This Class B digital apparatus complies with
Canadian ICES-003.
IC Radiation Exposure Statement:
This equipment complies with Canada
radiation exposure limits set forth for
uncontrolled environments.
This transmitter must not be co-located
or operating in conjunction with any other
antenna or transmitter.
Disposal of your old product
and battery
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
This product may contain lead and
mercury. Disposal of these materials
may be regulated due to environmental
EN
6 Notice
Notice of compliance
Notice for US
This set complies with the FCC rules, Part
15 and with 21 CFR 1040.10. Operation is
subject to the following two conditions:
a This device may not cause harmful
interference, and
b This device must accept any
interference received, including
interference that may cause undesired
operation.
FCC rules
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instruction
manual, may cause harmful interference to
radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment o and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
• Relocate the receiving antenna.
• Increase the separation between
equipment and receiver.
• Connect the equipment into an outlet on
a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
FCC Radiation Exposure Statement:
considerations. For disposal or recycling
information, please contact your local
authorities.
This product contains non-removable
batteries:
• Do not incinerate. Batteries may
explode if overheated.
• For disposal or recycling information,
please contact your local authorities.
Trademarks
Bluetooth
The Bluetooth® word mark and logos
are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such
marks by Gibson Innovations Limited
is under license. Onkyo® is a registered
trade mark of Gibson Brands Inc. Other
trademarks and trade names are those of
their respective owners.
12
7 Frequently
asked
questions
My Bluetooth headset does not switch on.
The battery level is low. Charge the headset.
I cannot pair my Bluetooth headset with a
mobile phone.
The Bluetooth is disabled. Enable the
Bluetooth feature on your mobile phone and
turn on the mobile phone before you turn on
the headset.
Pairing does not work.
Make sure the headset is in pairing mode.
• Follow the steps described in this user
manual (see ‘Charge and pair your
headset’ on page 4).
• Make sure that the LED light flashes
rapidly on the right side of the headset.
The mobile phone cannot find the headset.
•The headset may be connected to a
previously paired device. Turn o the
connected device or move it out of
range.
•Pairing may have been reset or the
headset has been previously paired
with another device. Pair the headset
with the mobile phone again as
described in the user manual (see
‘Charge and pair your headset’ on page
4).
My Bluetooth headset is connected to a
Bluetooth stereo enabled mobile phone,
but music only plays on the mobile phone
speaker.
Refer to the user manual of your mobile
phone. Select to listen to music through the
headset.
The audio quality is poor and crackling noise
can be heard.
The Bluetooth device is out of range. Reduce
the distance between your headset and
Bluetooth device, or remove obstacles
between them.
The audio quality is poor when streaming
from the mobile phone is very slow, or audio
streaming does not work at all.
Make sure your mobile phone not only
supports (mono) HSP/HFP but also supports
A2DP (see ‘Technical data’ on page 9).
Why is there a lag between the sound and
video when I use the ONKYO True Wireless
Headphones for watching videos or playing
games?
Constant audio lag behind video scenes would
be found when you are watching videos or
playing games with the ONKYO True Wireless
Headphones. The audio lag is due to the time
for audio synchronization between the left
and right sides of the headset, so the audio
may have delay compared to the video scenes.
Audio lag is not a problem for listening
to music with the Onkyo True Wireless
Headphones.
For further support, visit
www.onkyo-headphones.com
2016© Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold under the
responsibility of Gibson Innovations Ltd., and Gibson Innovations
Ltd. is the warrantor in relation to this product.
Onkyo® is a registered trade mark of Onkyo Corporation. Other
trademarks and trade names are those of their respective owners. BC
Other manuals for W800BT
2
Table of contents
Other Onkyo Headset manuals
