OnPoint OPG8H0AASSPSS User manual

SAFETY INFORMATION ........... 3
PARTS INCLUDED .................... 4
GETTING STARTED.................. 5
CONTROLS................................ 5
FUNCTIONS ............................ 6
CARE AND CLEANING............... 7
TIPS AND HINTS ....................... 8
LIMITED WARRANTY............. 9
CONSUMER SUPPORT ............. 10
OWNER’S MANUAL
OPG8H0AASSPSS / OPG8H1AASSPSS
ENGLISH
Write the model and serial numbers here:
Model #
Serial #
Find these numbers on a label
on the back of the unit.
IMMERSIONBLENDER

2
49-9000008 Rev. 0
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
When using this electrical appliance, which has sharp, moving parts, follow these important safeguards to
prevent a risk of personal injury:
IMPORTANT SAFEGUARDS :
1. READ ALL INSTRUCTIONS.
2. Be certain cover is securely locked in place before operating appliance.
3. Household use only.
4. To protect against electrical shock, do not put the motor body, cord or electrical plug of this hand blender in water or other
liquid. The detachable blending shaft of this appliance has been designed for immersion into water or other liquids. Never
submerge any other portion of this unit. If hand blender falls into liquid, remove immediately. Do not reach into the liquid
without unplugging the unitfirst.
5. This appliance should not be used by children and care should be taken when used near children.
6. Turn the appliance OFF, then unplug from the outlet when not in use, before assembling or disassembling parts and
before cleaning. To unplug, grasp the plug and pull from the outlet. Never pull from the power cord.
7. Avoid contacting with moving parts.
8. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is dropped or damaged
in any manner. Contact OnPoint Warranty at the website listed in the Contact Us section for information on examination,
repair, or adjustment.
9. The use of attachments or accessories not recommended or sold by OnPoint Warranty may cause fire, electrical shock, or
risk of injury, or damage to your immersion blender.
10. Do not use outdoors or use for other than intended use.
11. Do not let any cord hang over the edge of the table or counter.
12. Do not let cord contact hot surfaces, including stovetop.
13. When mixing liquids, especially hot liquids, use a tall container or make small quantities at a time to reduce spillage,
splattering and possibility of injury from burning.
WARNING

3
49-9000008 Rev. 0
14. Blades are SHARP. Handle carefully when unpacking, removing, inserting or cleaning. Exercise the same care when
removing or inserting the cutting blade for the chopper attachment.
15. Check the chopper for presence of foreign objects before using.
16. During operation keep hands, hair, clothing, as well as spatulas and other utensils away from attachments and any mixing
container, to prevent the possibility of severe injury to persons, and/or damage to the appliance. A spatula may be used
but must be used only when the unit is not operating.
17. Remove detachable shaft from the blender before washing the blades or shaft.
18. Make sure the appliance is off, the motor has stopped completely, and the appliance is unplugged from outlet before
putting on or taking off attachments, and before cleaning.
19. Maximum rating of 500W is based on baby food chopper attachment that draws the greatest power.
20. Never process ICE or other hard foods such as coffee beans, rice, frozen foods, spices, cereal or chocolate bars in the
chopping bowl as damage to the blades may result.
21. Never mix dry, thick or heavy mixtures for more than 15 seconds. Stop operation and stir the ingredients before continuing.
Allow the motor to rest for 1 minute between each use.
22. Never immerse the motor body in water or other liquids.
NOTICE: This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug will
fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician. Do not attempt to defeat this safety feature or modify the plug in any way.
READ AND SAVE THESE INSTRUCTIONS
WARNING RISK OF PERSONAL INJURY
HOLD THE BLADE ASSEMBLY BY THE PLASTIC STEM ONLY. DO NOT TOUCH THE RAZOR-SHARP
BLADES.
SAFETY INFORMATION

4
49-9000008 Rev. 0
PARTS
A
B
D
C
E
F
G
H
I
Parts
TopWrap (Cord Neck located on back side)
Low Button
High Button
Handle Grip
Main Body
ACCESSORY GUIDE
Main Body (E): G8H0AASSPSS & G8H1AASSPSS
Wand (G): G8H0AASSPSS & G8H1AASSPSS
Base (Attachments connect here)
Wand
Whisk
Chopper
Whisk (H): G8H1AASSPSS only
Chopper (I): G8H1AASSPSS only
A
B
C
D
E
F
G
H
I

5
49-9000008 Rev. 0
Getting Started
Before First Use
Features and Benefits
1. Speed Buttons: Press and hold down the preferred
speed. Once the button is released, blending willstop.
2. Comfort Handle: The handle allows you to controlthe
hand blender with ease.
Controls
3. Motor Body Housing
4. 'HWDFKDEOH 6KDIW: 7ZLVWLQJ DQG VOLGLQJ R ႇ IURP WKH
motor housing will detach the shaft for easy cleaning.
5. BlendingAttachment with Stainless Steel Blade and
Blade Guard: This attachment easily twists into the
motor body housing. The permanently mounted
stainless blade is partially covered by a stainless
housing that keeps splashing to a minimum.
6. Whisk Attachment: Whisk attachment twists into the
motor body housing. This attachment is great for
whippingcream,eggwhitesand other delectabletreats.
7. Chopper/Grinder Attachment: Chop, mince and grind.
Chopper/Grinder attaches to the blender motor bodyin
place of the blender shaft or whisk attachment.
High and Low Buttons
Speed Buttons: Press and hold down the preferred
speed. Once the button is released, blending will stop.
WARNING RISK OF PERSONAL INJURY
The blending blade is extremely sharp. Use caution
when removing and unpacking.
%HIRUH XVLQJ WKH EOHQGHU IRU WKH ¿UVW WLPH, ZH
recommend that you wipe the motor body with a
clean, damp cloth to remove any dirt or dust. Dry
it thoroughly with a soft absorbent cloth. HANDLE
CAREFULLY; wash blade assembly, mixing container
and detachable shaft by hand or in the dishwasher.
Dry thoroughly before use. Read all instructions
completely for detailed operating procedures.
GETTING STARTED / CONTROLS

6
49-9000008 Rev. 0
FUNCTIONS
Functions
Assembly of Attachments
Blending Attachment:
1. Align the motor body with the blending attachment,
then slide the pieces together. Twist the motorbody
clockwise and feel the pieces click together.
Chopper/Grinder Attachment:
1. 3XW WKH SUHS ERZO RQ D ÀDW, GU\,VWDEOH VXUIDFH.
2. The metal blade assembly shaft is attached to the
bottom of the prep bowl. If not already in place,slide
the blade assembly over the top of the metal blade
assembly shaft.
3. The chopper cover can only sit into the prep bowl. It
cannot be rotated.
4. Connect the motor body to the top of the chopper/
grinder attachment cover.
5. Plug the power cord into an electrical outlet.
6. Put one hand on the cover of the chopper/grinder
attachment, while gripping the handle with the other.
3UHVVWKH+LJKRU/RZEXWWRQZLWK\RXU¿QJHUVWRVWDUW
the motor and run the chopper/grinder. Toturn the unit
R ႇ ,UHPRYH\RXU¿QJHUVIURPWKHVHOHFWHGEXWWRQ.
7. WHEN THE BLADE STOPS MOVING, unplug the
Hand Blender, remove the motor body from the
chopper/grinder cover, and remove the cover from the
prep bowl.
Whisk attachment:
Align the motor body with the blending attachment, then
slide the pieces together. Twist the motor body clockwise
and feel the pieces click together.
Operation
Blending & mixing:
The specially designed blade is for mixing and stirring
all kinds of foods, including salad dressings, powdered
drink products, and sauces. It is ideal for combining dry
ingredients, and can be used to emulsify mayonnaise, too.
This blade mixes and stirs while adding only a minimum of
air to your mixture. A gentle up-and-down motion is all you
need to make the most flavorful, full-bodied liquid recipes.
Be careful never to remove the blender from the liquid
while in operation to avoid splatters.
1. Insert the blending attachment into the motor body.
2. Plug electrical cord into an electrical wall socket.
3. Insert blending shaft into mixture to be blended.
4. 3UHVV DQG KROG WKH 2Q/2 ႇ EXWWRQ. 7KH KDQG EOHQGHU
will continue to run as long as the switch is pressedin.
7RWXUQ KDQG EOHQGHU 2)), UHOHDVH WKH 2Q/2 ႇ EXWWRQ
and the motor will stop.
5. Do not hold the button On for longer than 50seconds
at a time.
6. Unplug immediately after use.
NOTE: When using blender in a saucepan, removepan
from stove.
Whisking:
1. Insert the whisk attachment into the motor body.
2. Plug electrical cord into an electrical wallsocket.
3. Insert the whisk into mixture to be blended.
4. Press and hold the desired speed button. Whendone
whisking, release the speed button.
5. Unplug immediately after use.
Chopping and Grinding Processing Food:
1. Put the prep bowl firmly on the flat sturdy surface like a
countertop.
2. Put food into the prep bowl. Be sure the food is cut into
small pieces, and the bowl is not overloaded.
3. Put the chopper/grinder cover on top of the prep bowl.
Be sure the cover is properly seated.
4. Press the ON/OFF button.
NOTE: Due to the powerful motor provided with this
unit, it is recommended using one hand to supportthe
chopper/grinder during operation.
6. When you finish processing the food, stop the
machine by taking your fingers off of the ON/OFF
button.
7. WHEN THE BLADE STOPS MOVING, remove the
blender motor body from the chopper/grinder cover,
and remove the cover from the chopper/grinder.
8. Unplug the unit.
9. Carefully remove the blade assembly, holding it by
the gripping the plastic stem. NEVER TOUCH THE
BLADE ITSELF.
10. Remove food with the spatula. Note: Do not operate
the Chopper/Grinder attachment without food in the
prep bowl.
WARNING HOLD THE BLADE ASSEMBLY BY
THE PLASTIC STEM ONLY. DO NOT TOUCH THE
RAZOR-SHARP BLADES.

7
49-9000008 Rev. 0
Care and Cleaning
Cleaning and Maintenance
Always clean the motor body and blending shaft
thoroughly after using. Remove the blending shaft from
the motor body. Clean the motor body only with a sponge
or damp cloth. Do not use abrasive cleaners which could
scratch the surface. To clean the blending shaft, wash by
hand in hot water using mild detergent. Be mindful of the
permanently mounted razor-sharp edges.
Chopper/Grinder Attachment
Tosimplify cleaning, rinse the prep bowl, cover, and
blade immediately after use, so that food won’t dry onto
them. Wash blade ring, plastic sheath, and prep bowl in
warm soapy water. Rinse and dry.Wipe the underside of
the chopper/grinder cover with a sponge or damp cloth
to remove any food. Do not submerge the cover in water
or put in the dishwasher. Wash the blade carefully. Avoid
leaving it in soapy water where it could disappear from
sight. If you have a dishwasher, you can wash the prep
bowl blade assembly on the upper shelf. Insert the prep
bowl upside down. Put the blade in the cutlery basket.
Unload the dishwasher carefully to avoid contact with
the sharp blade. Wipe the motor body and top of the
cover with a damp sponge or cloth. Dry it immediately.
Never submerge the motor body or the cover in water or
other liquid. The chopper/grinder attachment is intended
for HOUSEHOLD USE ONLY. Any service, other than
cleaning and normal user maintenance, should be
performed by an authorized Service Representative.
Whisk attachment
To clean your whisk attachment, simply release the
attachment from the motor body housing. Once the whisk
is removed, detach the metal whisk from the gearbox
by pulling pieces apart. To clean the gearbox, simply
wipe with a damp cloth. To clean the metal whisk, wash
with warm, soapy water or in the dishwasher. Do not
submerge the gearbox in water or any other liquid.
CAUTION FOR YOUR SAFETY
NEVER immerse the motor body in water or other
liquids.
When the appliance has malfunctioned or has been
dropped or damaged in any way or is not operating
properly, contact the manufacturer at the website listed
intheContactUssectionforinformationonexamination,
repair, or adjustment Any other servicing should be
performed by an authorized service representative.
CARE AND CLEANING

8
49-9000008 Rev. 0
TIPS AND HINTS
Tips and Hints
1. Liquid should come within an inch of where theshaft
attaches to the motor housing.
2. Some spices may scratch the chopper/grinder
attachment.
3. When using with a nonstick cooking surface, becareful
not to scratch the coating with the hand blender.
4. Do not immerse motor body housing, chopper/grinder
cover, or whisk gearbox in water or any otherliquid.
5. Cut most solid foods into ½-inch cubes for easy
blending. Suggestion: use chopper/grinder for
chopping and grinding solid foods.
6. Pour liquid ingredients into the mixing container
first, unless recipe instructs otherwise.
7. Toavoid splashing, don’t turn the hand blender on until
the blade is beneath the surface of the mixture and
do not pull the hand blender out of the mixture while
blender is running.
8. Do not let hand blender stand in a hot pot on stove
while not in use.
9. Do not put fruit pits, bones, or other hard material into
the blending mixture, as these are liable to damagethe
blades.
10. Do not fill mixing containers too full. The level
of mixture will rise when blending and can overflow.
11.Adding liquids that are warm, not cold, facilitates
blending solids with liquids.
12. For recipes calling for ice, use crushed ice (notwhole
cubes) for best results.
13. Using a gentle up-and-down motion is the best wayto
blend and incorporate ingredients uniformly.
14. To avoid splatter, turn the hand blender off and let
the blade stop completely before lifting the unit out of
the mixture you are processing.
15. Towhip air into a mixture, always hold the blade just
under the surface.
16. Tomake a soup creamy in texture, use the hand
blender to purée the soup solids to the desired
consistency using a gentle up-and down motion
right in the saucepan. Youcan quickly change your
soup into a thick and creamy blend.
17. If you are making a dip or spread, it is notnecessary
to process completely into a smooth purée; leave
some texture for interest.
18. When making compound butters, remove the
butter from the refrigerator and let it come to room
temperature before blending in the ingredients.

9
49-9000008 Rev. 0
Small Appliances Limited Warranty
Pleasehaveyourserialnumberandyourmodelnumberavailablewhenrequestingservice at
https://www.onpointwarranty.com/small-appliances-cx-portal
For Terms and Conditions, please visit
https://f.hubspotusercontent20.net/hubfs/4854028/GE_First%20Build/RefurbGoodsT&C.pdf
Staple your receipt here. Proof of the original purchase date is needed to obtain service under the warranty.
LIMITED WARRANTY

10
49-9000008 Rev. 0
CONSUMER SUPPORT
Consumer Support
Service and Registration
Register your new appliance on-line at your convenience! Timely product registration will allow for enhanced
communication and prompt service under the terms of your warranty, should the need arise.
Register your appliance at https://www.onpointwarranty.com/small-appliances-cx-portal
Contact Us
If you are not satisfied with the service you receive from OnPoint, contact us at
https://www.onpointwarranty.com/small-appliances-cx-portal with all the details including your phone number,
or write to: 9900 Corporate Campus Drive, Suite 2050, Louisville, KY 40223