OpeMed OT200 User manual

User Manual
Contents
1 Introduction
1.1 About this manual................................................................................2
1.2 Symbols ..............................................................................................2
1.3 Contents of the package.......................................................................2
1.4 The OT200 ceiling hoist........................................................................3
1.5 Points of attention................................................................................4
2 Description
2.1 Overview OT200 ..................................................................................5
2.2 Control Panel.......................................................................................5
2.2.1 Charging and life span of the batteries ..................................................6
2.2.2 Emergency cord...................................................................................6
2.2.3 Emergency control ..............................................................................6
2.2.4 Indicator lights ....................................................................................7
2.2.5 Connecting the hand-held control..........................................................7
2.2.6 Connecting the powered hanger bar......................................................7
2.3 Hand-held control ................................................................................7
2.4 Carousel (optional)...............................................................................8
2.5 Gate (with X-Y system) (optional) .........................................................8
2.6 Hanger bar..........................................................................................9
2.7 Slings..................................................................................................10
2.7.1 Sling attachment..................................................................................10
2.7.2 General information about slings...........................................................11
2.7.3 Types and sizes of slings ......................................................................11
2.7.4 Washing instructions slings...................................................................13
3 Use
3.1 Before use...........................................................................................14
3.2 Lifting the caretaker with the OT200 .....................................................14
3.2.1 Lifting from a chair...............................................................................14
3.2.2 Lifting from a bed ................................................................................15
3.2.3 Attaching the sling to the hanger bar.....................................................15
3.3 Moving the caretaker with the OT200....................................................15
3.4 Taking the caretaker out of the OT200 ..................................................16
4 Maintenance
4.1 Cleaning instructions ............................................................................17
4.2 Daily/Weekly maintenance....................................................................17
4.3 Annual inspection and maintenance by OpeMed.....................................17
4.4 If the OT200 does not function .............................................................17
4.5 Disposal ..............................................................................................17
5 Appendix
5.1 Warranty statements............................................................................18
5.2 About OpeMed.....................................................................................18
5.3 Contact details.....................................................................................18
5.4 EG-Statement of conformity.................................................................19

2 • • • User Manual ref1109
•Introduction 1
1.1 About this manual
The aim of this user manual is to enable carers to operate the OT200 and to instruct them on how to
carry out small (preventive) maintenance jobs.
This manual deals with the following aspects related to operating the OT200:
• Parts description
• Working principle description
• Step-by-step lifting instructions
• Maintenance of the OT200; to be carried out by the carer
Next to this manual the following documentation is available on the OT200:
• Technical manual. The technical manual is developed for the technical service department and contains:
- maintenance procedures
- repair procedures
- parts lists with order numbers
• Installation manual. This manual can be used during the installation of the systems
- installation of rail and supports
- installation of a gate (transition from fixed to mobile rails)
- installation of carousel
-part lists with order numbers of all components of the rail system.
• Quick Reference. The Quick Reference guide deals with the main safety and operating aspects relating
to the OT200
1.2 Symbols
Attention Read the manual before operating the hoist
Attention, High Voltage The producer of the product
With this, the OT200 meets the European Standard, ISO 10535 and the
GQ-quality mark T-02, cluster UTT.
1.3 Contents of the package
The delivered package must contain:
• Cassette • Technical manual
• Hand-held control • User manual
• Charger • Quick reference
• Charging station
Remove the packaging from the OT200 and check the contents of the package.

Ref1109 User Manual • • • 3
•Introduction 1
1.4 The OT200 Ceiling Hoist
The OT200 is a ceiling hoist for passive transfers of caretakers. The
caretaker can be lifted with the OT200 and it is possible to transfer
the caretaker by means of a rail that is attached to the ceiling. The
OT200 can be delivered with a mechanical (balanced) or powered
hanger bar. The OT200 can also be equipped with an electrical drive
for transportation along the rail.
The OT200 can be used for the following transfers:
• From a (wheel)chair to a bed and vice-versa.
• From a (wheel)chair to a toilet and vice-versa.
• From a (wheel)chair to a shower-bath-toilet chair and vice-versa.
•From the floor to a (wheel)chair or bed.
The OT200 cannot be used to help caretakers with standing up or walking (usually an
active hoist like the James will be used for these purposes).
The OT200 complies with the following standards (by KBOH):
• The user can be lifted from a sitting or lying position and will hang in a (semi)sitting position. After
transportation of the hoist, the user can be placed back on the supporting element in a sitting or lying
position.
• The hoist can be used in combination with wheelchairs, without having to remove foot, leg or arm
supports.
• The hoist can be used in combination with an accessible bed, shower window or dressing table at
working height. Next to this the hoist can be used for transfers to and from the floor.
With this the OT200 also complies to the demands set by the European Standards, ISO 10535
and the GQ-quality mark T-02, cluster UTT.
Under normal conditions, and with the exception of slings and batteries, the expected life span of the
hoist is 10 years (100.000 transfers), provided the hoist is maintained as instructed.
Special circumstances, like using the OT200 in humid environments or environments with aggressive
vapours can shorten the life time of the hoist.

4 • • • User Manual ref1109
•Introduction 1
1.5 Points of attention
•The OT200 is designed to lift and transfer caretakers in combination with an appropriate sling, the
OT200 can only be used for this purpose. Any other form of use is not allowed.
•It is not allowed to lift more than 200kg (440lbs.) with the OT200, unless otherwise stated on the lift.
•It is not allowed to lift any object (e.g. a chair or wheelchair) together with the caretaker.
•Special caution needs to be taken when the clips of a sling are attached to the hanger bar, incorrectly
attaching these clips can cause a fall of the caretaker and lead to severe injuries.
•Always make sure sufficient space is available above the caretaker before lifting.
•Only use the OT200 in combination with a sling that is delivered by OpeMed. Always contact OpeMed
before using alternative slings.
•Treat the lift with care and always make sure the working environment is neat and clean.
•Working with the hoist is only allowed to authorized personnel.
•The OT200 needs at least once a year a periodical inspection.
•Service and maintenance of the hoist is only allowed to be carried out by authorized personnel.
•Only use original parts(supplied by OpeMed) for repairs or replacements.
•Replacing hanger bars or other constructive parts of the hoist is only allowed to authorized personnel.
•Charging the battery always needs to be done in well ventilated, dry rooms. Battery chargers need to
be connected according to the installation demands.
•Battery chargers need a periodical inspection at least once a year.
•Never lift the caretaker higher than necessary.
•When deformations occur to the hoist due to incorrect usage or transport, the hoist should not be used
anymore, and will have to be sent back to the supplier.
•Avoid collision into end stops at full speed.
•Move the hoist carefully in order to prevent excessive movements of the caretaker.
•Never leave the hoist unattended while loaded. In energy saving mode (after 10 minutes) the load will
be lowered slowly.
•Do not use the hand-held control orthe hanger bar wires as towing-lines to move the caretaker as this
will damage the wiring.

Ref1109 User Manual • • • 5
• •Description 2
2.1 Overview OT200
The parts in figure 1 will be described in separate chapters.
1 Cassette page 6
2 Control panel page 7
3 Emergency cord page 6
4 Hoisting belt
5 Connection socket hand-held control
6 Connection socket hanger bar
Figure 1 The OT200 cassette
2.2 Control panel
1 Emergency cord see 2.2.1
Emergency control see 2.2.2
2 Green indicator on-off see 2.2.3
3 Orange battery indicator see 2.2.3
4 Red failure indicator see 2.2.3
5 Connection hand-held control see 2.2.4
6 Connection hanger bar see 2.2.5
Figure 2 Control panel

6 • • • User Manual ref1109
• • Description 2
2.2.1 Charging and life span of the batteries
In order to maximize the life span of the batteries, it is advised to put the cassette into the
charging station when the cassette is not being used.
Always charge the battery when the orange battery indicator is blinking.
Charge the batteries according to the following procedure:
- Make sure the charger is connected to the grid.
-The green indicator on the charger will light up.
-Place the cassette below the charging strips.
-After several seconds charging will start automatically.
-The red indicator on the charger will light up while the battery is being charged.
(The orange indicator on the cassette will light up.)
-The red indicator light will dim when the battery is fully charged.
(The orange indicator on the cassette will also dim.)
-Allow for a charging time of 8 hours.
Capacity
The number of lifting cycles that can be done with a fully charged battery depends on the time per lifting
cycle, the lifted weight and the age and condition of the battery.
Discharging
Abattery which is not used for a longer time will automatically discharge. Too much discharging of the
battery reduces the battery’s capacity. This will result in the fact that less lifting cycles can be done with a
battery.
2.2.2 Emergency cord
By pulling the red emergency cord the hoist will immediately stop
moving. The emergency stop is (de)activated as follows:
Activate emergency stop (figure 3A). Pull the emergency cord.
De-activate emergency stop (figure 3A). Press the red lip to which the
cord is attached back into the cassette. After this the cassette will
function as normal.
Do not use the emergency cord as an on-off switch.
Reactivating the cassette is done with the red lip
which is close to the ceiling. The cassette will
automatically turn off when it has not been used for more than 10 minutes.
A B
Figure 3 Emergency cord
2.2.3 Emergency control
(Only to be used in the case of an emergency)
The emergency control can only be used when there is no other way to get the caretaker out of the hoist.
The emergency control usesspare power that is available in the battery. The emergency control can only
be used to lower a caretaker and is controlled by pulling the emergency cord. As long as the cord is being
pulled down (fig. 3B) the hoist will keep lowering the caretakers.
The OT200 is also equipped with several other safety systems. Examples are the rewind guard and a slack
belt guard. A detailed description of these safety systems can be found in the technical manual.

Ref1109 User Manual • • • 7
• • Description 2
2.2.4 Indicator lights
Green indicator on-off
The green indicator will light up when the cassette is activated. The cassette will automatically deactivate
when it has not been used for 10 minutes. The green indicator will dim. The cassette will automatically
reactivate when the hand-held control is being used.
Orange battery indicator
The battery indicator tells when the batteries need to be charged. When this indicator starts to blink, the
batteries will have to be charged following the description in paragraph 2.1.1. When the hoist is being
lowered while loaded, the battery will charge and therefore the orange indicator will light up.
Red failure indicator
When the red failure indicator lights up there is a failure inside the cassette. Immediately alarm your
technical service department.
2.2.5 Connecting the hand-held control
The plug of the hand-held control has to be connected to the cassette by screwing the threaded plug into
the cassette. (fig. 2-5)
2.2.6 Connecting the powered hanger bar
When the cassette is equipped with a powered hanger bar, the threaded plug of the hanger bar has to be
screwed into the cassette. (fig. 2-6) When the hanger bar is connected correctly it can be controlled with
the hand-held control.
2.3 Hand-held control
Do not use the hand-held control as a towing line! Stand behind the caretaker and
steadily push him or her along the rail. The hanger bar can be used as a handle for transfers.
1 Hoist
up
2 Hoist down
3 Hanger bar to sitting position
4 Hanger bar to lying position
5 Move cassette to the left
6 Move cassette to the right
Figure 4A 4-function hand-held control Figure 4B 6-function hand-held control
The OT200 is operated with either a 4-or6-function hand-held control. This control is used to:
• move the hoist up or down.
• bring the hanger bar from a lying position into a sitting position (only with powered hanger bar)
• move the cassette (only with powered drive of the cassette).

8 • • • User Manual ref1109
• • Description 2
2.4 Carousel (optional)
The system you have chosen might be supplied with a
carousel as depicted in figure 5. A carousel creates the
possibility of running a cassette along more than one
rail. A carousel operates automatically and makes a
quarter-turn to the left or the right. A full turn is not
possible.
Controlling the carousel is simple:
• Place the cassette in the middle of the carousel.
•After approx. 2 seconds the carousel will turn 90
degrees.
•Drive the cassette out of the carousel.
• If you do not want to make a turn but simply pass the carousel,
you should not stop the cassette in the carousel.
Figure 5 Carousel
2.5 Gate (with X-Y systems)
If your system uses a X-Y system with a transition to
a fixed rail thena “gate” is placed where the rails
join (figure 6). This gate makes sure that the
cassette cannot slide out of the rail when the joints
are not alligned. The gate automatically connects the
railsand enables a smooth transition from a mobile
to a fixed rail.
From fixed rail to X-Y system:
• Move the cassette through the gate toward the
mobile rail.
•The rail will de-attach and can be moved.
Figure 6 Gate
From X-Y system to a fixed rail:
• Place the cassette in front of the gate.
•Place the rail with the cassette opposite to the other gate.
(keep moving slightly)
•The rails will connect and cannot be moved anymore.
The guard will open and the cassette can be moved through the gate.
It is important not to disconnected the gate from the grid. When the gate is on the fixed rail
and the power is disconnected the gate will not function anymore and a transfer to the mobile
rail is not possible. Atechnician will have to reset the gate.

Ref1109 User Manual • • • 9
• • Description 2
2.6 Hanger bar
The OT200 is provided with a hanger bar. The hanger bar is a construction to which the sling (in which
the caretaker will take place)can be attached. Several types of hanger bars are available, of which the
balanced and the powered hanger bar are the most important types. Both hanger bars create the
possibility of transporting the caretaker in a sitting or a lying position. The way this is done is described
below.
STANDARD –2 Point spreader Bar
For use with loop slings (OpeMed and approved competitors)
OPTIONAL EXTRA - Balanced hanger bar
A balanced hanger bar is influenced by the caretaker. The caretaker can bring
himself/herself into a sitting or a lying position with simple movements. The balanced
hanger bar is most efficient when used with caretakers who have sufficient stability in
the hip-joint and sufficient body balance.
OPTIONAL EXTRA - Powered hanger bar
The powered hanger bar is moved from a sitting to a lying position by means of an
actuator on the hanger bar. This enables automatic positioning of the caretaker into
the desired position, which has high benefits for caretakers with a low hip-stability. The
powered hanger bar is controlled by two buttons on the hand-held control. (paragraph
2.3).
1 Sitting position
2 Lying position
3 Attachment head side
4Attachment leg side
5 Hanger bar engine
Figure 7a Sitting position hanger bar Figure 7b Lying position hanger bar
Do not use the hanger bar cord as a towing line! This might damage the wiring. Stand
behind the caretaker and steadily push him or her along the rail. The hanger bar can be used
as a handle for transfers.

10 • • • User Manual ref1109
• • Description 2
2.7 Slings
2.7.1 Sling attachment
Sling attachment
Read these guidelines carefully before using the sling. It is ESSENTIAL that you fully
understand how to attach the sling in the correct way. Always check the sling for signs of wear
or damagebefore use.
LOOP SLINGS
Attach the loop over the hook, taking care that the same length of loop is attached on either side.
Ensure both leg and shoulder loops are attached (min of 4 loops on any sling)
Always refer to the sling user guide
Always check the weight capacity of the sling and ensure it is not more than the OT200
CLIP SLINGS
1 Hold on to the strip on the clip with one hand and pull the large hole in the clip over the attachment
point. Check whether the belt on which the sling is hanging is not turned or twisted.
2Take the belt under the clip and pull this down until the clip falls into the secure position.
3The attachment point is now locked into the hole in the top side of the clip.
4Attach all clips in the same way before lifting.
The clip can be de-attched by pulling it upwards and sliding it of the attachement point. Make
sure all tension is of the clips before deattaching them in order not to endanger the caretaker.
Attachment point

Ref1109 User Manual • • • 11
• • Description 2
• • • Use 3
3 .1 Before use
Check the OT200 on the following points before use:
• Check that status of the batteries on the cassette´s display
• Is the emergency stop de-activated?
• Check whether the used sling fits the purpose and the transfer (see tables page 11 and 12)
• Check the condition of the sling and the clips and whether the whalebones are placed
• Carefully place the sling
• Is the caretaker able and comfortable to be lifted?
• The cassette will automatically activate when any button on the hand-held control is pushed
• When using a standard sling, always place the arms of the caretaker inside the sling on the caretakers’
lap.
•When using a toilet sling always make sure the arms of the caretaker are outside the sling so that the
upper slips with clips pass beneath the arms!
• Always work in a neat and clean environment.
• The OT200 is now ready to be used according to the instructions in this manual.
Always make clear to the caretaker what is happening with every step of the process!
Pay attention to the danger of getting entangled between the hinging points of the hanger
bar.
3.2 Lifting the caretaker
Step 3.2.1 Lifting from a chair
• Place the sling behind the back of the caretaker down to the seat. Let the caretaker sit slightly forward
during this handling. Make sure the sling is placed with the washing instructions facing to the outside.
• Pull the leg slips slightly forward, this way the caretaker already sits ‘inside’ the sling.
• Lift one of the caretaker’s legs and bring one leg slip of the sling to the inside of the leg. Use the same
method to apply the other leg slip.
• If necessary, pull the head side of the sling up to the correct height. The sling will now fit around the
caretaker like a ‘tank chair’.
• When using a toilet sling apply the circular belt (leg-side) like a belt around the waist of the caretaker.
Put the arms of the caretaker through loops on the head-side of the sling.
Toilet slings can only be used with caretakers with sufficient shoulder functioning and body
stability.

12 • • • User Manual ref1109
• • • Use 3
3.2.2 Lifting from a bed
• Roll-up one slide of the sling for about half the total width of the sling.
• Roll the caretaker over on one side, facing the carer.
• Put the sling with the rolled-up side against the back of the caretaker.
• Make sure the sling is placed with the washing instructions facing to the outside (currently the down
side).
• Roll the caretaker over the sling onto his/her other side.
• The rolled-up part of the sling will now be on the side of the carer.
• Unroll the rolled-up part of the sling and pull this to the correct position.
• Roll the caretaker back on his or her back, making sure he or she is now lying on the sling.
• Lift one of the caretaker’s legs and bring one leg slip of the sling to the inside of the leg.
• Do the same with the other leg slip.
• If necessary straighten the sling in order to make sure the caretaker will lie stable during lifting.
3.2.3 Attaching the sling to a hanger bar
• When lifting from a chair, put the hanger bar in a sitting position (figure 7a page 9).
• When lifting from a bed, put the hanger bar in a lying position (figure 7b page 9).
• Make sure the caretaker is facing the hanger bar
Make sure the belts on the clips are not
twisted. If the leg slips are turned the clips
can undo themselves.
3.3 Moving the caretaker
Do not use the hand-held control as a towing line! This might damage the wiring. Stand
behind the caretaker and steadily push him or her along the rail. The hanger bar can be used
as a handle for transfers.
• Lift the caretaker by means of the hand-held control.
• While moving, walk with the lift. Stay as close to the caretaker as possible.
• Approach the bed, chair or toilet and then determine the required height for bringing the caretaker to
the final position.
Never lift the caretaker higher than absolutely necessary during a transfer.

Ref1109 User Manual • • • 13
• • • Use 3
3.4 Taking the caretaker out of the OT200
Step 1a Lifting towards a bed
• Bring the caretaker into a lying position. Position the caretaker as good as possible above the bed.
• Lower the caretaker onto the bed until he or she completely lies flat on the bed.
• Undo the clips of the sling from the hanger bar and remove the hoist.
• Alway use a special bath sling when lifting towards a bath.
Step 1b Lifting towards a (wheel)chair
• Make sure the brake of the wheelchair is applied.
•Lower the caretaker into the chair at low speed.
• Make sure the caretaker is properly positioned into the back of the chair.
• Undo the clips of the sling from the hanger bar and remove the hoist.
Step 1c Lifting towards a toilet
• Follow the same instructions as when lifting to a chair.
• Always us a toilet sling when lifting to a toilet.
• Lower the caretaker’s pants to the knees before placing the caretaker on the toilet. Further lower the
pants after placing the caretaker on the toilet.
• Undo the toilet sling from the attachment points of the hanger bar while using the toilet.
• Raise the caretakers pants after the toilet use again to the knees, lift the caretaker and fully raise the
pants.
Toilet slings can only be used with caretakers with sufficient shoulder functioning and body
stability.

14 • • • User Manual ref1109
• • • Maintenance 4
4.1 Cleaning instructions
Cassette and hanger bar The best way to clean the OT200 is with a moist cloth. Use normal
(house)cleaning detergents.
Slings - See washing instructions, paragraph 2.7.4, page 13. Do not use
aggressive solvents when cleaning the hoist or the slings.
4.2 Daily/Weekly maintenance
For normal use the OT200 hardly requires maintenance. We do however advice to pay attention to the
following points daily in order to prevent or recognize problems in time.
Action Remark
Clean the hoist: See cleaning instructions paragraph 4.1
Wash the slings: See washing instructions, paragraph 2.7.4, page 13.
Charge the batteries regularly: Make sure the cassette is in the charger when the hoist is
not being used.
Check whether the hoist operates smooth: Alarm the technical service department in order to let
them grease or change parts that hinder smooth
operation.
Check for irregular sounds: Alarm the technical service department
If any doubt occurs about the condition or functioning of the OT200 always alarm the technical
service department.
4.3 Annual inspection and maintenance
The hoist needs to be checked once a year according to the NTA-guidelines. This needs
to be done by OpeMed or another authorized institution. Opemed offers you the
possibility of an annual inspection by means of an Annual Inspection Agreement.
This mark (figure 12) tells you when the hoist is due for inspection. For more
information about inspections you can always contact OpeMed.
Figure 12
4.4 If the OT200 does not function
• Check whether the emergency cord is pulled out (red lip on cassette, see paragraph 2.2.1 op page 6)
• Check whether the batteries are sufficiently charged.
• Check whether the plug of the hand-held control is connected correctly.
• Check whether the plug of the hanger bar control is connected correctly.
• Check whether the belt is slack, if necessary tighten it.
• Check whether the belt has been pulled up too much, the hoist will only go down.
• Check whether the belt has been rolled out too much, the hoist will only go up.
• When the hoist is still not working, alarm the check technical service department.
4.5 Disposal
For disposal the OT200 can be returned to OpeMed. This is also possible with batteries, chargers, slings
etc. If you choose to dispose the batteries yourself, be aware of the fact that these batteries are chemical
waste.

ACCESS LIFTS LIMITED
0843 216 0226
Access Lifts Limite
Unit 6 Concept Centre, Innovation Close Poole
Dorset BH12 4QT
Registere in Englan No.03231129
Registere Office 35 Cassel Avenue Poole Dorset BH13 6JD
www.access-lifts.co.uk