OpenVox B200P User manual

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
OpenVox Communication Co.Ltd
B200P/BE200P on DAHDI User Manual
Version: 2.2

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
1
OpenVox Communication Co.Ltd
Most Advanced Asterisk Cards
Address: F/3, Block No.127, Jindi Industrial Zone,
Shazui Road, Futian District, Shenzhen, Guangdong 518048, China
Tel:[phone], Fax:[phone]
Business Contact: [e-mail]
Technical Support: [e-mail]
Business Hours: 09:00-18:00(GMT+8) from Monday to Friday
URL: www.OpenVox.cn
Thank You for Choosing OpenVox Products!

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
2
Copyright
Copyright© 2011 OpenVox Inc. All rights reserved. No part of this document may be
reproduced without prior written permission.
Confidentiality
Information contained herein is of a highly sensitive nature and is confidential and
proprietary to OpenVox Inc. No part may be distributed, reproduced or disclosed
orally or in written form to any party other than the direct recipients without the
express written consent of OpenVox Inc.
Disclaimer
OpenVox Inc. reserves the right to modify the design, characteristics, and products at
any time without notification or obligation and shall not be held liable for any error or
damage of any kind resulting from the use of this document.
OpenVox has made every effort to ensure that the information contained in this
document is accurate and complete; however, the contents of this document are
subject to revision without notice. Please contact OpenVox to ensure you have the
latest version of this document.
Trademarks
All other trademarks mentioned in this document are the property of their respective
owners.

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
3
Contents
General Safety Instructions ........................................................................................4
Test Environments.......................................................................................................5
Chapter 1 Overview.....................................................................................................6
1.1 What is Asterisk................................................................................................6
1.2 What is B200P/BE200P....................................................................................7
Chapter 2 Hardware Setup.........................................................................................9
2.1 Power supply.....................................................................................................9
2.2 Slot compatibility..............................................................................................9
2.3 Setting Card ID ...............................................................................................10
2.4 Adjusting Termination of S/T Interface (100 ohm) ........................................10
2.5 Power Feeding Connector...............................................................................11
2.7 Hardware setup procedure ..............................................................................12
Chapter 3 Software Installation and Configuration...............................................14
3.1 Download........................................................................................................14
3.2 Installation.......................................................................................................17
3.3 Configuration..................................................................................................20
Chapter 4 Reference..................................................................................................28
Appendix A Specifications ........................................................................................29
Appendix B PIN Assignments...................................................................................30

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
4
General Safety Instructions
CAUTION
1. The computers that have B200P/BE200P card installed must comply
with the country’s specific safety regulations.
2. Only service personnel should install B200P/BE200P card.
3. Before you install B200P/BE200P card, please unplug the power cord
from the computer and remove the cover from your PC.
4. For avoiding personal injuries and damage to your computer and
B200P/BE200P card, make sure bracket of the card is secured to the
PC’s chassis ground by fastening the card with screws.
5. Electrical Surges, ESD are very destructive to the equipment. To avoid
it, make sure there is a low impedance discharge path from your
computer to chassis ground.
6. To reduce the risk of damage or injury, please follow all steps or
procedures as instructed.

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
5
Test Environments
CentOS-5.6
Kernel version: 2.6.18-238.12.1.el5
DAHDI: dahdi-linux-complete-2.4.1.2+2.4.1
Asterisk: 1.8.5.0
Libpri: 1.4.11.5
Hardware: OpenVox B200P/BE200P

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
6
Chapter 1 Overview
1.1 What is Asterisk
The Definition of Asterisk is described as follows:
Asterisk is a complete PBX in software. It runs on Linux, BSD, Windows
(emulated) and provides all of the features you would expect from a PBX
and more. Asterisk does voice over IP in four protocols, and can
interoperate with almost all standard-based telephony equipments using
relatively cost-effective hardware. Asterisk provides Voicemail services
with Directory, Call Conferencing, Interactive Voice Response, and Call
Queuing. It supports three-way calling, caller ID services, ADSI, IAX,
SIP, H323 (as both client and gateway), MGCP (call manager only) and
SCCP/Skinny (voip-info.org).
PC+Softphone
SIP phone
Analog phone
Switch Asterisk
VOIP PBX
Operating System Linux and FreeBSD
OpenSource Drivers Asterisk®,DAHDI,
Zaptel,Bristuff,Misdn and ISDN4BSD
Protocol SIP, IAX, SS7, MGCP, H323, R2 and more..
Applications IVR, CRM, FAX, E-mail, CallCenter, Billing
and your application..
Figure 1 Topology

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
7
1.2 What is B200P/BE200P
OpenVox B200P/BE200P is a PCI 2.2 compliant card which supports 2
BRI S/T interface, and BE200P is B200P with an hardware echo
cancellation module. It takes full advantage of Siemens® technology
based Hardware Echo Cancellation Module to deliver the superior voice
quality over the 2 BRI ports that can be configured for TE or NT mode
individually by jumpers. This port configuration is detected by the driver
automatically.
B200P/BE200P S/T BRI interface card delivers superior voice quality in
the telephony systems with advanced Siemens® technology based
hardware echo canceller. It can provide 4 simultaneous voices calls over 2
ISDN BRI line, turns your legacy ISDN BRI equipments into powerful
Voice over IP devices and provides a soft migration path from ISDN
technology to the new Voice over IP world. B200P/BE200P is designed
for building Open Source systems based on Asterisk such as ISDN PBX
and VoIP gateway.
The B200P/BE200P and drivers comply with fully GPLed for the Linux
kernel bring powerful ISDN BRI connectivity to your Linux machine.
B200P/BE200P works well with Asterisk®, Elastix®, FreeSWITCH™,
PBX in a Flash, trixbox®, Yate™and IPPBX/IVR projects as well as other
Open Source and proprietary PBX, Switch, IVR, and VoIP gateway
applications.

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
8
Target applications
High Performance ISDN PC Cards
ISDN PABX for BRI
VoIP Gateways
ISDN LAN Routers for BRI
ISDN Least Cost Routers for BRI
ISDN Test Equipment for BRI
Main features
Supports PCI 2.2 or above, 3.3 V and 5 V PCI slot
ITU-T I.430 and TBR 3 certified and S/T ISDN supporting TE/NT
mode
Industry standard full size length PCI card
32 bit bus master DMAdata exchanges across PCI interface at
132Mbytes/sec for minimum host processor intervention
DTMF detection on all B-channels
Multiparty audio conferences bridge
Full software and hardware compatible with Junghanns.NET ISDN,
mISDN driver, DADHI and so on.
RoHS compliant
Certificates: CE, FCC, A-Tick
trixbox TM Officially Certified
Elastix® Officially Certified

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
9
Chapter 2 Hardware Setup
There are some points should be paid attention to when setting up
B200P/BE200P.
2.1 Power supply
The board is powered by PCI slot, but some newest model PCs do not
provide +5V on PCI slots, in such cases, you have to set the jumper to
3.3V.
2.2 Slot compatibility
B200P/BE200P is compatible with 32-bit 3.3V PCI slot, 32-bit 5.0V PCI
slot, 64-bit 3.3V PCI slot and 64-bit 5.0V PCI slot except PCI-E slot; you
should confirm your slot type firstly and then insert B200P/BE200P into
any type of PCI slot as previously described. Some slots are described
like that.
64-bit 5.0V PCI slot
64-bit 3.3V PCI slot
32-bit 5.0V PCI slot
PCI-E ×1 slot
32-bit 3.3V PCI slot
1
2
3
4
5
Figure 2 PCI-E and PCI slots

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
10
2.3 Setting Card ID
If want to install more than one card of B200P/BE200P in a PC, you
should take care of the card id switch. The state of ON stands for "1" and
OFF represents "0", Card ID is calculated by binary. For instance, the
four switches should be all set to OFF if there is only one card, which
means their corresponding binary value is "0000" and . There two pieces
of rules you must obey to set Card ID:
The ID of the first card must be set to 0, and the second should be set
to 1, and so forth.
The first card is a card that will be initialized (i.e. installing driver)
firstly when the system boot up. At most cases, Linux will initialize
PCI devices according to their slot order. The slot nearest to the CPU
will be initialized firstly and the far end slot will be initialized at last.
That is to say, the card which is nearest to the CPU ID should be set
to 0 if there are more than one B200P/BE200P on your machine.
2.4 Adjusting Termination of S/T Interface (100 ohm)
You are able to set a port to NT or TE mode, please refer to figure 3 for
visualized information.
If a port works on NT mode, you should set jumper to CONNECT
(ON).
If a port works on TE mode, theoretically it should be set to OPEN

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
11
(OFF), but it might connect to some non-standard ISDN terminal
equipments that do not have terminal resistors, for such equipments,
you should set it to CONNECT(ON).
2.5 Power Feeding Connector
These jumpers control whether supply power for the external ISDN
terminals. Users should adjust accordingly from the following:
If the port works on TE mode, users MUST set the jumper to
OPEN(OFF)
If this port will work on NT mode, and the ISDN terminal requires
ISDN power supply, users should set the jumper to CONNECT (ON).
While ISDN terminal does not require ISDN power supply, users
should set the jumper to OPEN (OFF).
2.6 Power Supply
Power Feeding Input
If one of the eight power feeding connectors is CONNECT (ON), users
should connect a D-type connecter from PC power supply to this jack, the
D-type connecter is used to provide power to CDROM and 3.5”HDD.
Power Supply Selection
Some latest model PCs do not provide +5V on the PCI slots. If use those
kinds of PCs, users have to set the jumper to 3.3V.

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
12
PCM IN/PCM OUT
The above feature is applied to connect two BRI cards.
OpenVox
B200P
Termination of S/T Interface (100 ohm)
Connect: Termination = ON
Open: Termination = OFF
Power Supply Selection
4-PIN 12V Input
Voltage Port
NT/TE Settings
NT mode TE mode PCM OUT
PCM IN
Power Feeding Connector
Connect: Power feeding to
feed S/T interface enable
Open: Power feeding to feed
S/T interface disable
Set Card ID
SW1
SW2
SW3
SW4
012 3
ID
SW
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
……
……
……
……
……
Figure 3 Jumper setting
2.7 Hardware setup procedure
Power off your PC, remember to unplug the AC power cable
Set card ID as previously stated if there are more than one BRI card
and set the switches appropriately.
Insert B200P/BE200P into a 3.3V or 5.0V PCI slot vertically
Plug the hard disk power supply cable (D style) to power feeding

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
13
input jack if it is need to provide power by external equipments,
please refer jumper setting section for more details.
Plug ISDN lines into RJ-45 interfaces which set as TE mode and
ISDN phone lines into RJ-45 interface which set as NT mode
Fix the board by a screw
Plug back the AC power cable, and power on PC
Caution: During the above processes, an ESD wrist strap
is needed. Once power is on, you must not attempt to
install or take down the board. After hardware setup
appropriately, it is time to install software.

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
14
Chapter 3 Software Installation and Configuration
B200P/BE200P supports DAHDI software driver on Linux. To make full
use of B200P/BE200P, you should download, compile, install and
configure DAHDI, Libpri and Asterisk. Let’s make specific versions for
an example to state how to install software.
3.1 Download
DAHDI software packages are available on OpenVox official website or
Digium. Some patches should be applied when the driver source is from
Digium. Therefore, it is recommended that downloading the DAHDI
driver package from OpenVox official website.
Gain DAHDI source package from OpenVox:
http://downloads.openvox.cn/pub/drivers/dahdi-linux-complete/openvox_
dahdi-linux-complete-current.tar.gz
Get Libpri and Asterisk software packages from Digium official website:
http://downloads.asterisk.org/pub/telephony/libpri/releases/libpri-1.4.11.
5.tar.gz
http://downloads.asterisk.org/pub/telephony/asterisk/releases/asterisk-1.8
.5.0.tar.gz
Execute the following commands under the directory of /usr/src/ in

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
15
generally to download and decompress these packages:
#_wget_http://downloads.asterisk.org/pub/telephon
y/libpri/releases/libpri-1.4.11.5.tar.gz
# tar -zxvf libpri-1.4.11.5.tar.gz
#_wget_http://downloads.openvox.cn/pub/drivers/da
hdi-linux-complete/openvox_dahdi-linux-complete-c
urrent.tar.gz
# tar -zxvf dahdi-linux-complete-current.tar.gz
#_wget_http://downloads.asterisk.org/pub/telephon
y/asterisk/releases/asterisk-1.8.5.0.tar.gz
# tar -zxvf asterisk-1.8.5.0.tar.gz
Also you can get the DAHDI source code from Digium official website,
but need to get a patch from OpenVox official website for Hardware Echo
Cancellation Module:
# wget http://downloads.asterisk.org/pub/telephon
y/dahdi-linux-complete/releases/dahdi-linux-compl
ete-2.4.1.2+2.4.1.tar.gz
# tar -zxvf dahdi-linux-complete-2.4.1.2+2.4.1.ta
r.gz

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
16
# wget http://downloads.openvox.cn/pub/drivers/da
hdi-patches/b200p_b400p/wcb4xxp.tar.gz (For BE200P)
# tar -zxvf wcb4xxp.tar.gz
Use the files decompressed from wcb4xxp.tar.gz to replace the original
files in /dahdi-linux-complete-xx/linux/drivers/dahdi/wcb4xxp before you
compile DAHDI.
If using Asterisk 1.8, it is not need to make any patches more.
If using Asterisk 1.6, please modify the file
asterisk-1.6.xx/channels/chan_dahdi.c as the following introduction.
Please comment out the following line:
/*ast_log(LOG_WARNING, "How cool would it be if someone Implemented
this mode!For now, sucks for you.(line %d)\n", v->lineno);*/
Then add the following two lines after the above action:
confp->chan.sig = SIG_BRI_PTMP;
confp->pri.nodetype = PRI_NETWORK

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
17
3.2 Installation
1. Hardware detection
# lspci –vvvv
Check the outcome and confirm your system has recognized
B200P/BE200P. If it has been recognized, "ISDN controller" will be
displayed in the output information like that:
02:09.0 ISDN controller: Cologne Chip Designs GmbH ISDN network
Controller [HFC-4S] (rev 01)
Subsystem: Cologne Chip Designs GmbH Device e884
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 217
Region 0: I/O ports at dff0 [size=8]
Region 1: Memory at feafb000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: wcb4xxp
Kernel modules: wcb4xxp
Figure 4 Hardware detection
If B200P/BE200P is not recognized by the system, you have to power off
and take out the card to insert it into another PCI slot.
2. Software installation
Some dependencies are crucial. If any of them is absent, the software

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
18
installation process would not go through successfully. Let’s run "yum
install XX"(XX stands for the dependency’s name) to check the
availability of dependencies.
# yum install bison
# yum install bison-devel
# yum install ncurses
# yum install ncurses-devel
# yum install zlib
# yum install zlib-devel
# yum install openssl
# yum install openssl-devel
# yum install gnutls-devel
# yum install gcc
# yum install gcc-c++
# yum install libxml2
# yum install libxml2-devel
If there is no kernel source in the system, you should also
install it by running like:
# yum install kernel-devel
If the dependency has been installed, system will indicate that nothing to

B200P/BE200P on DAHDI User Manual
OpenVox Communication Co. LTD. URL: www.openvox.cn
19
do, which means you could go to next one directly. Otherwise, the system
will keep on installing it.
Change to the directory dahdi-linux-complete-XX (XX represents
DAHDI version), then perform commands one by one to install DAHDI.
# cd /usr/src/dahdi-linux-complete-2.4.1.2+2.4.1
# make
# make install
# make config
Caution: If there is something wrong after "make",
please refer to HERE. In the url link, the moderator
introduces you a method how to patch. After patching,
save your changes and exit. Then run "make"again, if successfully done,
it is time for you to install Libpri and Asterisk.
Please execute those commands to install Libpri and Asterisk:
# cd libpri-1.4.11.5
# make
# make install