OPT7 QUANTUM ROCK LIGHTS User manual

QUANTUM ROCK LIGHTS
INSTALL GUIDE
FULL-SIZE REMOTE CONTROL BUTTON LAYOUT
x6
10ft Extension Cable
Fuse Tap (3 dierent sizes) x1
Metal Screw x8
12V Constant Power Wire x1
x4 x4
1
Full-Size Remote x1
2 YEAR WARRANTY
Quantum Rock Light Pod Rubber Pad
Control Box x1
1
2
3
4
5
6
SPECIFICATIONS
OPT7 Lighting is not liable for damages or personal injuries
while installing this product. The Installation Guide is
intended as assistance to reduce setup time. OPT7 Lighting
assumes no responsibility for improper installation.
If you are unfamiliar with your vehicle or inexperienced with
aftermarket upgrades, please seek professional assistance.
Wattage
Amp Draw
8 LEDs
Brightness
Voltage
Resistance
Operating Temperature
DISCLAIMER
Only control “RGB” light
Brightness Setting: 50 Levels
20 different solid modes
Brightness Setting: 50 Levels
Brightness Setting: 4 Levels
Default 3 color variations (Random)
Supports brightness and speed adjustment
Default 3 color variations (Random)
Supports speed adjustment
Default 7 color variations (Random)
Supports brightness and speed adjustment
Default 20 color variations (Random)
Supports brightness adjustment
Default 20 color variations (Random)
Supports brightness and speed adjustment
Play all dynamic style modes
Speed Setting : 10 Levels
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
8W Per Pod
8A
Quad-Core CREE
1,600 Lumens Per Pod
12V
IP68 Water-Resistant (Pod Only)
-20°-150°F
4
ON & OFF
Dimmer +/-
Color Selector
Independent Control Of White Light
Style Mode
Quick/Slow
ON & OFF
Dimmer +/-
Default brightness
3 Color Cycle
3 Fade
7 Color Cycle
Beat/SoundSYNC
Strobe
AUTO
W
GB R
25% 50% 75% 100%
SLOW
QUICK
OFF ON
OFF ON
AUTO
COLOR
STROBE
CYCLE
COLOR
CYCLE
COLOR
FADE
BEAT
W
GB R
25% 50% 75% 100%
SLOW
QUICK
OFF ON
OFF ON
AUTO
COLOR
STROBE
CYCLE
COLOR
CYCLE
COLOR
FADE
BEAT
3
2 1
4
5 6

INSTALLATION STEPS
Designate your mounting locations for each Rock Light Pod and the
control box. (Refer to page 2 for recommended mounting locations)
Avoid hot surfaces and/or moving parts.
Use a pen to mark the holes where you want to mount the Rock Light
Pods. Then, drill a 5/32” hole(s) for the wire connector to pass through.
Drill a 7/64” hole for each marked hole.
Secure the Rock Light Pods using the included screws. (If mounting on a
rounded or uneven surface, utilize the optional rubber mounting pads.)
Caution: Rock Light Pods become extremely hot during use - keep
away from any vehicle parts that may be damaged by exposure to
high temperatures.
Connect all Rock Light Pod lines to the control box connectors. Secure
by twisting.
Connect the red positive line from the control box directly to the
vehicle battery.
Ground the negative wire from the control box by connecting it to an
unpainted area on your vehicle's frame.
Using a fuse tap, connect the 12V control wire from the control box to a
power source that turns on ONLY when the key is turned to ACC/ON or
a switched fuse position.
Some examples of these power sources are: radio, dome light or those
that are marked as accessory in your owner's manual or on your fuse
box cover diagram.
The kit will not function without this connection.
1.
2.
3.
4.
5.
6.
7.
8.
WHERE TO INSTALL
FRONT
REAR
FRONT
REAR
TOOLS REQUIRED
32
5/32-inch Drill Bit
7/64-inch Drill Bit
Phillips Head Screwdriver
•
•
•
RECOMMENDED LOCATIONS FOR ROCK LIGHT PODS
If you are uncomfortable performing work of this nature yourself, then do
not hesitate to consult a professional for help. Working with a vehicle’s
electrical system can be hazardous to an unqualified individual. OPT7 is not
liable for damages or personal injuries while installing this product. The
installation guide is provided as assistance to reduce set up time.