Optex InSight Series User manual

INS-CUBE
INS-CUBE
INSTALLATION INSTRUCTIONS
Quick Guide
1
2
3
4
- Specifications
- LED indications
- Dimensions
- Detection area
- Compliance
Before installation
Others
<< Contents >>
Page
1
2
3
4
Step
Enable
Disable
Testing
Installation
Registration InSight to CHeKT portal site
DHCP
IP address settings
VISUAL VERIFICATION PIR CAMERA
Warning
Caution
Prohibition Recommendation
Failure to follow the instructions provided with this indication and improper
handling may cause death or serious injury.
Failure to follow the instructions provided with this indication and improper
handling may cause injury and/or property damage.
NOTE Special attention is required to the
section of this symbol.
- Manufacturer's statement
Before installation
Full information is available at
https://www.optexamerica.com
This “Quick Guide” is the part of the entire installation instructions
that guides the installation procedures for installers.
Get the full information of the installation instructions from the web site.
If you need a guide to the operation of the whole system, please
consult the installer of the entire system.
•
•
•
1
series
For more information about Camera
setting, see our website.
www.optexamerica.com
- Manufacturer's statement
- Parts identification
- Accessories
- CHeKT account
CHeKT support
https://support.chekt.com
Destroy
/Modify
Wetting with waterOutdoor installation
Detection through glass Partial/complete obscuration
of the detection area.
Tilt
Mounting height
2.0 to 3.0 m (6'7" to 9'8")
3.0 m (9'8") recommended
Follow to the Regulations
Warning
Caution
1-1. Install the mounting bracket
1-2. Remove the main unit from the base unit
1-3. Install/Remove an SD Memory Card
(optional)
1-4. Wiring
1-5. Mounting body
1-6. Secure the main unit to the base unit
4-1. Walk test and camera angle checking
4-2. System test

- Accessories
2
- Parts identification
1Installation
Step
Mounting Screw &
Plastic Anchor-4pcs
Mounting Template
Cable Hole.
Mounting Bracktet DC Plug Jack Screw 1pc
Speaker
Lens
Mic
LED
PIR Sensor
Illumination Sensor
Main unit
Base unit
SD Card Slot
Lan Port
12V DC Port
Alarm
Terminal Port
Reset / WPS
Main unit (Rear side)
1-1. Install the mounting bracket
Wall mount Corner mount
Mounting screw x 2 Mounting template
Mounting bracket
Mounting screw x 4
1-2. Remove the main unit from the base unit
1
2
Remove the accessory screw, if already installed.
Press the buttons on the
both sides to release the
main unit.
2
1-3. Install/Remove an SD Memory
Card (optional)
5
1-4. Wiring
To Alarm Terminal Port
To LAN Port
To 12 V DC Port
Reset / WPS
Main unit (Rear side)
Factory reset
Press the rest button for 5 seconds
to return the setup to the factory default.
If you press the Reset button, you will lose all the setting data.
If needed, make a note for further installation.
T1 T2 +12V GND N.O COM N.C
Power source Consumption
12 V DC 6.4 W
IEEE 802.3af Class 3 6.8 W 12
3
1Powe connection
Check the voltage and current capacity
of the power source before connecting.
2Network connection
Connect the crossover cable into the RJ-45.
3Alarm connection
T1: Tamper switch
T2: Tamper switch
NOTE
Warning
Caution
Install
Remove
N.O.: Normally open
COM: Common
N.C.: Normally close
+12V: 12 V DC power
GND: Ground
- CHeKT account
If you do not have a CHeKT account, request a dealer
account by visiting the "CHeKT dealer", before Step 3.
Refer to the “CHeKT support" for more details.
CHeKT support
https://support.chekt.com
CHeKT dealer
www.chekt.com/registration

3
2IP address settings
Step 3
Device registration to CHeKT portal
Step
The default network type of InSight is dynamic.
If you have a DHCP server, it will automatically set the InSight. Jump to Step 3
If you do not have a DHCP server, it will set as follows after one minute.
Initial address: Refer to the label on the InSight
User name: root
Default password: OPTEX
Change your password as appropriate.
Download IP installer;
IP installer is available as a dedicated software for searching
IP addresses of CUBE.
See our website. www.optexamerica.com
Setup your CHeKT Dealer Portal:
1. Go to http://dealer.chekt.com/ to log in.
2. Select the Customer on the left side of the dashboard.
3. Select the Site Devices tab.
4. Select the bridge device to be associated with the sensor camera.
5. Access the bridge settings using the gear icon to its right.
6. Select the appropriate tab to register the PIR camera.
Refer to the site for more details.
CHeKT suppor
https://support.chekt.com
4-1. Walk test and camera angle checking 4-2. System test
4Testing
Step
Walk in the detection area to check the detecting performance via LED indication. Check the image at the time of detection
on the monitoring portal.
1-5. Mounting body
Base unit Mounting Bracket
1
Fasten the base unit to the mounting bracket fixed on the wall.
Tighten the screw to prevent the base unit movement.
2
1-6. Secure the main unit
1
Fasten the accessory screw to secure the main unit.
Press the buttons on both sides to install
the main unit.
2
1
1
2

- Detection area
Others
- Specifications
FCC notification
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed andused in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
Personal Information
This product is equipped with the function to produce moving and/or still image of the designated area and its surrounding
and can store the recorded imagewhich includes the information such as face of an individual that could identify the
individual. Prior to the installation of this product, the compliance to local laws and regulations needs to be confirmed by the
user of this product for the lawful installation and use of this product, and signage and notification when using this product.
User of this product is deemed to be responsible for the compliance of any laws and regulations relating to personal
information, privacy protection and rights of portrait upon use of this product. Image taken by this product is required to be
treated appropriately under the responsibility of the user of this product. OPTEX Co., Ltd. and its subsidiaries (hereinafter
collectively called “OPTEX") shall not wilfully obtain or utilise the image taken by this product. However, only when dealing
with troubles of this product upon request of user, OPTEX may obtain and utilize the necessary image recorded by this
product. When doing so, OPTEX shall not treat such image for the purpose of identifying an individual. OPTEX shall treat
such image according to its Privacy Policy. When requesting OPTEX to support a trouble of this product, the user may be
required to perform applicable legal notification. Ensure to follow the appropriate procedure prior to sharing of personal
information and data to OPTEX. Installation of this product, producing image, monitoring, recording with camera and
handling of personal information or data shall all be performed under discretion and responsibility of user of this product,
and OPTEX shall not be held liable for any dispute between a user and a third party.
- Compliance
About distribution of source code for open source software
This product includes open source software（” OSS”） distributed under OSS License. In compliance with the OSS Licenses
such as GPL (GNU GENERAL PUBLIC LICENSE), LGPL (GNU LESSERGENERAL PUBLIC LICENSE), and/or others
included, we are making the source code of the OSS available, at the actual cost, to our customer upon his/her request.
The source code corresponding to OSS included in this product will be provided in a prescribed manner for at least than
three(3) years after the date of purchase. Please note that the OSS is provided without warranty of any kind.
4
Distributed by
OPTEX INC./AMERICAS HQ (U.S.)
www.optexamerica.com
Top view
Side view
0 2 4 6 8 10 m
10 m
8
6
4
2
0
2
4
6
8
10
0 5 10 15 20 25 30 ft.
0 2 4 6 8 10 m
2 m
1
0 5 10 15 20 25 30 ft.
30 ft
25
20
15
10
5
0
5
10
15
20
25
30
8 ft.
6.6
4
120°
Unit: mm (inch)
- Dimensions
87.6 (3.45)
114 (4.49)
96.8 (3.81)
60 (2.36)
72.1 (2.84)
- LED indicator
• Specifications and designs are subject to change without prior notice.
• These units are designed to detect an intruder and activate an alarm control panel. Being only a part of a complete system,
we cannot accept responsibility for any
damages or other consequences resulting from an intrusion.
Passive infrared
Up to 10m, 120° angle of view
Model
PIR Detection
Detection method
PIR coverage
INS-CUBE
1/2.8" Progressive Scan CMOS
2.8mm, F1.6
0.035 lux, AGC on/0 lux with IR (F1.6)
Up to 10m
110°
IR cut filter with auto switch
1/15 s to 1/32,000 s
Camera
Image sensor
Lens
Min. illumination
IR range
Angle of view
Day/Night
Shutter times
1,920 x 1,080
60 Hz, 30 fps
3D DNR
Ture WDR
Rotate mode, Saturation, Brightness,
Contrast, Sharpness, AGC, ROI
H.264, H.265, MJPEG
100 kbps to 10 Mbps
G.711
Image and compression
Max. image resolution
Frame rate
Digital noise reduction
Wide dynamic range
Image setting
Video compression
Video bit rate
Audio compression
Environmental and mechanical
Operarion temperature
Environmental humidity
Dimensions
Weight
IEEE 802.11.b, 802.11g, 802.11n
2.4 GHz to 2.4835 GHz
20 MHz support
802.11b: CCK, QPSK, BPSK
802.11g/n: OFDM
64/128 bit WEP, WPA/WPA2,
WPA-PSK/WPA2-PSk, WPS
25 m (Dependent upou environment)
Wi-Fi
Wireless standard
Frequency range
Channel bandwidth
Protocols
Security
Wireless range
12 V DC ± 10%, PoE (802.3af)
12 V DC 6.4 W, PoE (802.3af) 6.8 W
1 RJ45 10 M/100 M Ethernet port
Built-in microphone
Built-in speaker
1 channel signal
1 channel signal
Electrical and interface
Power supply
Power consumption
Communications
Audio input
Audio output
Alarm output (N.O./N.C.)
Tamper alarm (switch)
-20°C - 50°C (-4°F - 122°F)
90% max
87.6 mm x 114 mm x 72.1 mm
297 g
PIR detection, Network disconnect
IP address conflict, Storage exception
Temperature critical, Audio detection
Built-in Micro SD, SDHC, SDXC
card slot, up to 128 GB
One-key reset, Flash-prevention,
Dual stream, Password protection,
Privacy mask, IP address filtering,
Anonymous access
TCP/IP, ICMP, HTTP, HTTPS, DHCP,
DNS, DDNS, RTP, RTSP, RTCP, NTP,
UPnP, SNMP, IGMP, 802.1X, QoS,
IPv6, Bonjour
Functions
Alarm triggers
Local storage
Security
Protocols
Camera
PIR
[1] ALARM
[2] STATUS
[3] LINK
Wired LAN
Wi-Fi
Warm-up PIR
detection Stand-by
0.5 s intrval
1 s interval
Blue Red Green
Blue
Yellow Yellow Yellow
Yellow Yellow Yellow