Optex AX100 User manual

AXTFR Basic configuration guide
AX100/200TFRTI Configuration guide

AX100/200TFR (30M/60M Battery powered active beams)
AX100/200TFR set a new benchmark for reliable, flexible, low maintenance
external detection systems. CCTV, Intruder, hazard alerts and numerous other
applications can be serviced by this flexible battery powered technology
Minimal
system
design
time
Minimal
damage or
site
disruption
Flexible Tower
or single beam
configuration
options
No
cable or
power
surge
Minimal site
survey
investment
Compatible
with most
Wireless
transmitters
=
Cost
Reduction
3-5 YEAR BATTERY LIFE

AX100/200TFR (30M/60M Battery powered active beams)
Undulating ground can cause missed alarms
when using long range beams on perimeters
Undulating ground can be easily managed with Battery powered
AXTFR option and prevent missed alarms

Multiple short range beam can direct PTZ to target position
In CCTV applications a single long range beam makes it difficult
to direct the camera to where the intruder is?

B ONLYActivated = OPEN CIRCUIT = ALARM (Possible threat)
B = NC
A = NO
A ONLYActivated = CLOSED CIRCUIT = No Alarm (Not interesting)
A+B Both Activated = CLOSED CIRCUIT = Truck (Not interesting)
AX TFR can provide target recognition in areas
where activity is expected
but needs to be ignored
These configurations could be reversed to detect larger targets
and ignore others
No need for any power infrastructure means that installation is
completed in hours rather than days. This is critical for some
public transport and public service sectors

AX100/200TFR (30M/60M Battery powered active beams)
AX100/200 TFR can signal an alarm via wireless,
GSM, pager or hardwired connection if available.
A typical example of cable use is where existing
cables are limited or have been damaged.
Battery power means that site security can be
expanded easily, moved or used as temporary
security installations.
Interchangeable signalling mediums means you are
never restricted to one protocol. AXTFR can move
with the times and your customer needs

4 Channel frequency
makes Tower
configuration easy

Simple battery replacement
Loosen
1st Step 2nd Step
Remove
3rd
Step
4th
Step
Put back
Battery replacement
does not involve
interference with
alignment system

AX100/200TFR (30M/60M Battery powered active beams)
Triple tamper
(1)Front Cover (2)Back Box(3)Wall

Conventional solution has
higher risk of detection
blocking and false alarms
AX TFR can provide security
where zone block causes a major
problem
AXTFR can overcome and
eliminate these problems

Secure windows and balcony access Early warning for low bridge
Monitor access to roof or
fire escape
Driveways and gates for vehicle
and pedestrian detection
No mains power supply
needed
Simply mount and align the
beams

AX100/200TFR (30M/60M Battery powered active beams)
AX100/200 TFR are supplied as standard with no
batteries and no wireless transmitters.
This is because the AXTFR can utilize numerous
wireless technologies including : Honeywell, Visonic,
Scantronics, Inovonics etc
Each set of AX100/200TFR require 4 LHS20 batteries
to power the devices. Two for the TX and two for the
RX. Based on these batteries the beams can be
powered for 5 years (AX100TRF) and 3 years
(AX200TFR).
If you wish to signal the output from the device via
your choice of wireless technology then you can ac-
commodate the wireless device within the AXTFR
housing.
Note there are numerous configurations available.
The installer needs to consider the application and
signalling requirements.
The following pages are examples of how various
configurations are possible using Inovonics wireless
products

Common option for CCTV or Intruder
Using AX100/200TFRTI Version.
(These can also be used with 16 channel 1216M Receiver)
Here we have 2 sets of beams signalling Alarm, tamper, low battery and
supervisory. The EE1210 is fitted at the AXTFR Transmitter and Receiver
Note
Tamper output
is common.

Typical option for CCTV
Here we have 4 sets of beams signalling Alarm, tamper, low battery and
supervisory. The EE1212 is an option to the EE1210.
Dome
Pre-set
Dome
Pre-set
Note
AX100/200TFRTI are supplied fitted
with x2 EE1210 and require x4 LHS20

Basic option for CCTV or Intruder
Here we have 4 sets of beams signalling limited Alarm, tamper, low battery
and supervisory. The EE1210 is fitted only at the AXTFR Receiver
Note
No tamper
Signal sent
From AXTFR
Transmitter

AX-100/200TRF
Supplied as standard with no batteries and no
wireless transmitters.
AX-100/200TRFTI
Supplied as standard with no batteries and two
EE1210 wireless transmitters.
LHS20 Batteries
Not supplied as standard with any product. Four
required for each set of beams
Note for Inovonics recievers
4 Channel receiver has 4 Alarm outputs
16 channel receiver has 9 outputs
Specifications may change without notice. Please contact our office for
any site survey assistance or advice you may require on
01628631000