Resolution Products RE612 CryptiX User manual

Page
1
of
6
3/23/15
24-Hour Tech Support Line: (715)808-0164
www.ResolutionProducts.com
RE612 CryptiX™
™™
™-Compatible Smoke Alarm
Features
• UL217 Listed
• Sleek design
• Wall tamper
• Strong, reliable RF signal
• Low attery indication
Key Instructions
1. Read the “INSTALLING YOUR SMOKE ALARM” section:
• Install your Smoke Alarm.
2. Enroll the Smoke Alarm in a panel:
• Place panel in enrollment mode
• Press & hold TEST button until you hear the sounder beep.
• Panel will learn the Smoke Alarm.
3. Test the Smoke Alarm is enrolled in a panel:
• Press & hold TEST button until you hear the sounder beep.
• Panel will indicate a Smoke Test.
4. Read the “WEEKLY TESTING OF YOUR SMOKE ALARM” section:
• Test the functionality of the Smoke Alarm.
Operation
Situation
Sounder
LED
Wireless Signal to
Panel
Recovery
Actual smoke
Temporal 3
(Loud)
RED
(pulsing)
Wireless Smoke Alarm
Signal sent to panel
Silence an actual alarm with the
TEST button. Sensor will return
to alarm if smoke is still present.
Press & hold
Test utton
Temporal 3
(Loud)
RED
(pulsing)
Wireless Smoke Test
Signal sent to panel
Sens
or: estore by releasing the
test button
Removing
Sensor from
Mount
Temporal 3
(Loud)
Yellow
(steady)
Tamper/Trouble
signal to be sent to
panel.
Sensor: estore by remounting.
Low attery
Chirp
Yellow
/Red
(blink)
Hourly Check
Supervisories, every
h
our
Maintenance
Needed
Temporal 3
(Loud)
Yellow
(Pulsing)
Supervisories Not
Sent
eplace Unit
Attention
This manual should be read prior to use and retained for further information.
Page
2
of
6
3/23/15
24-Hour Tech Support Line: (715)808-0164
www.ResolutionProducts.com
Specifications
Approval: UL217 Single Station Smoke Alarm & Heat Alarm
Smoke Sensitivity: 1.31 – 2.28 %/ft
Heat Temperature: 135 to 140 F
Smoke Technology: Photoelectric
aHeat Alarm Point: 135 – 149 F (UL
Alarm Sound: Temporal Three
Replacement attery: Panasonic CR123A
Duracell DL123A
Temperature Range: 32 to 120 F (Long Term)
Humidity: 10 – 85% Relative Humidity
Housing dimensions: 4.7 inch diameter, 2.1 inch high
Frequency: 433.92 MHz
System Compatibility: RE6100 series panels with capacity of up to 96 zones
User's Manual: 47-0001-08 Rev A
Design & Manufacture: Resolution Products, Inc.
1402 Heggen Street
Hudson, WI 54016

Page
3
of
6
3/23/15
24-Hour Tech Support Line: (715)808-0164
www.ResolutionProducts.com
INSTALLING YOUR SMOKE ALARM
RE612 Smoke Alarm is made to be mounted on the ceiling or on the wall if necessary.
Read “LOCATIONS TO INSTALL YOUR SMOKE ALARM” A D “LOCATIONS NOT TO INSTALL YOUR SMOKE ALARM” sections in the Manual first, then decide where to install a Smoke Alarm.
Please follow these steps to install your s oke alar :
1.
At the place where you are going to install your Smoke Alarm, draw a vertical line six inches long.
2.
Remove the mounting bracket from your unit by rotating it counter-clockwise.
3.
Place the bracket so that the two longest hold slots are aligned on the line. In each of the keyhole slots, draw a mark to locate a mounting plug and screw.
4.
Remove the bracket.
5.
Using 3/16-inch (5 mm) drill bit, drill two holes at the marks and insert plastic wall plugs. Place the Smoke Alarm in a location where it cannot get any dust on it when you drill holes for
mounting.
6.
Using the two screws and plastic wall plugs (all supplied), attach the bracket to the wall.
7.
Line up the slot of the bracket and the Smoke Alarm. Push the alarm onto the mounting bracket and turn it clockwise to fix it into place. Pull outward on the Smoke Alarm to make sure
it is securely attached to the mounting bracket.
Figure: Removable mounting bracket
CAUTION
: This Smoke Alarm comes with battery cover latches that will prevent the Smoke Alarm from closing if the battery is not installed. This tells you that the smoke alarm will not work until a
battery is properly installed.
NOTE
: The alarm horn will beep once after the detector is installed with a battery and mounted on the bracket (2 – 4 seconds). This means the Smoke Alarm is working normally and also indicates
that the battery is positioned properly. Once the smoke alarm is mounted press the test button, holding it down for about 3 seconds until the horn sounds. The horn should sound a loud pulsating
alarm. This means the unit is working properly.
REGULAR MAINTENACE
Your Smoke Alarm is designed to be as maintenance-free as possible. To keep your Smoke Alarm in good working condition, you must test the unit weekly, as described in section “WEEKLY TESTI G OF
YOUR SMOKE ALARM”
Open the cover and vacuu the dust off the alar 's sensing cha ber at least once a onth.
Remove the battery before cleaning. To clean the Smoke Alarm, use the soft brush attachment to your vacuum. Carefully remove any dust on the Smoke Alarm components, especially on the
openings of the sensing chamber. Replace the battery after cleaning. Test the Smoke Alarm to make sure the battery is working correctly. ever use water or cleaners as they may damage the unit.
Figure: Removable cover of smoke chamber
NOTE
: If nuisance alarms keep coming from the unit, you should check whether the Smoke Alarm’s location is adequate. Refer to “LOCATIONS TO INSTALL YOUR SMOKE ALARM” to move your
Smoke Alarm if it is not located properly.
WEEKLY TESTING OF YOUR SMOKE ALARM
Test the Smoke Alarm weekly by pushing firmly on the test button with your finger for around 4 seconds until the horn sounds, the sound pattern is 3 beeps, pause, and then 3 beeps with the red LED
flashing continuously and rapidly. If the Smoke Alarm beeps three times and the yellow LED flashes three times in 43 seconds, it indicates the Smoke Alarm is not working properly, and it needs to be
repaired or serviced.
This is the only way to ake sure that the S oke Alar unit is working properly. If the unit fails to test properly, have it repaired or replaced i ediately.
If you suspect that your Smoke Alarm does not go into alarm, test it by pressing the test button with your finger to ensure if it works properly.
WARNING
: ever use an open flame of any kind to test your Smoke Alarm. You may set fire or damage the Smoke Alarm, as well as your home. The built-in test switch accurately tests the Smoke
Alarm unit's operation as required by UL217.
WARNING
: When you are not testing the unit and the alarm horn sounds this means the Smoke Alarm has sensed smoke or combustion particles in the air. Be certain that the alarm horn is a warning
of a possible serious situation, which requires your immediate attention.
•
The alarm could be caused by a nuisance situation. Cooking smoke or a dusty furnace, sometimes called “friendly fires” can cause the alarm to sound. If this happens, open a window or
fan the air to remove the smoke or dust. The alarm will turn off as soon as the air is completely clear.
•
NOTE
: Do not disconnect the power or remove the battery from the Smoke Alarm. This will remove your protection from fires.
Page
4
of
6
3/23/15
24-Hour Tech Support Line: (715)808-0164
www.ResolutionProducts.com
If the alar horn begins to beep once in 43 seconds with the yellow LED blinking at the sa e rate, this signal eans that the S oke Alar 's battery is weak. Replace with a new battery
i ediately.
•
Keep fresh batteries on hand for this purpose. Replacement batteries can be purchased at a local hardware store.
•
NOTE
: Use only the replace ent batteries listed below.
◦
Panasonic CR123A 3V
◦
Duracell DL123A 3V
WARNING
: Do not use any other kind of battery. This Smoke Alarm may not operate properly with another kind of battery.
LOCATIONS TO INSTALL YOUR SMOKE ALARMS
Smoke Alarms should be installed in accordance with the FPA Standard 72 ( ational Fire Protection Association, Battery March Park, Quincy, MA 02169). For complete coverage in residential units,
Smoke Alarms should be installed in all rooms, halls, storage areas, basements, and attics in each family living unit. Minimum coverage is one alarm on each floor and one in each sleeping area.
USEFUL TIPS FOR YOU:
• Install a smoke alarm in the hallway outside every separate bedroom area, as shown in Figure 1.
• Two Smoke Alarms are required in homes with two bedroom areas, as shown in Figure 2.
Figure 1: Locations for placing Figure 2: Locations for placing
Smoke Alarms for single residence Smoke Alarms for single-floor residence
with only one sleeping area. with more than one sleeping area.
• Install a smoke alarm on every floor of a multi-floor home or apartment, as shown in Figure 3.
Figure 3: Locations for placing
Smoke Alarms for a multi-floor residence
• Install a minimum of two Smoke Alarms in any household.
• Install a Smoke Alarm inside every bedroom.
• Install Smoke Alarms at both ends of a bedroom hallway if the hallway is more than 40 feet (12 meters) long.
• Install a Smoke Alarm inside every room where one sleeps with the door partly or completely closed, since smoke could be blocked by the closed door and a hallway alarm may not wake
up the sleeper if the door is closed.
• Install basement Smoke Alarms at the bottom of the basement stairwell.
• Install second floor Smoke Alarms at the top of the first-to-second floor stairwell.
Be sure no door or other obstruction blocks the path of s oke to the S oke Alar .
• Install additional Smoke Alarms in your living room, dining room, family room, attic, utility and storage rooms.
• Install Smoke Alarms as close to the center of the ceiling as possible. If this is not practical, put the Smoke Alarm on the ceiling, no closer than 4 inches (10 cm) from any wall or corner,
as shown in Figure 4.
• If ceiling mounting is not possible and wall mounting is permitted by your local and state codes, put wall-mounted Smoke Alarms between 4 and 6 inches (10 – 15 cm) from the ceiling,
also see Figure 4.
• If some of your rooms have sloped, peaked, or gabled ceilings, try to mount Smoke Alarms 3 feet (0.9 meter) measured horizontally from the highest point to the ceiling as shown in
Figure 5.
• On ceilings with exposed joists or beams, Smoke Alarms shall be mounted on the bottom of the joists or beams as shown in Figure 6.
Figure 4: Recommended best and Figure 5: Recommended locations Figure 6: Recommended locations
acceptable locations to mount to mount Smoke Alarms in rooms on ceilings with exposed joists or beams.
Smoke Alarms. with sloped, gabled, or peaked ceilings.
NOTE:
Specific requirements for Smoke Alarm installation vary from state to state and from region to region. Check with your local Fire Department for current requirements in your area.

Page
5
of
6
3/23/15
24-Hour Tech Support Line: (715)808-0164
www.ResolutionProducts.com
LOCATIONS NOT TO INSTALL YOUR SMOKE ALARMS
uisance alarms take place when smoke alarms are installed where they will not work properly. To avoid nuisance alarms, do not install smoke alarms in the following situations:
IMPORTANT: For any reason, do not disable the unit to avoid nuisance alarms.
• Combustion particles are the by-products of something that is burning. Thus, in or near areas where combustion particles are present you do not install smoke alarms to avoid nuisance
alarms, such as kitchens with few windows or poor ventilation, garages where there may be vehicle exhaust, near furnaces, hot water, and space heaters.
• Do not install smoke alarms less than 20 feet (6 meters) away from places where combustion particles are normally present, like kitchens. If a 20-foot distance is not possible, e.g. in a
mobile home, try to install the alarm as far away from the combustion particles as possible, preferably on the wall. To prevent nuisance alarms, provide good ventilation in such places.
• In air streams near kitchens. Air currents can draw cooking smoke into the sensing chamber of a smoke alarm near the kitchen.
• In damp or very humid areas or near bathrooms with showers. Moisture in humid air can enter the sensing chamber and then turn in droplets upon cooling which can cause nuisance
alarms. Install smoke alarms at least 10 feet (3 meters) away from bathrooms.
• In very cold or very hot areas including unheated buildings or outdoor rooms. If the temperature goes above or below the operating range of smoke alarms it will not work properly. The
temperature range for your smoke alarm is 0°C (32°F) ~ 49°C (120°F).
• In very dusty, dirty, or greasy areas. Do not install a smoke alarm directly over the stove or range. Keep laundry room smoke alarms free of dust or lint.
• ear fresh air vents or very drafty areas like air conditioners, heaters, fans, fresh air vents and drafts which can drive smoke away from smoke alarms.
• In insect-infested areas. If insects enter an alarm's sensing chamber they may cause a nuisance alarm. Where bugs are a problem get rid of them before putting up an alarm.
• ear fluorescent lights as electrical “noise” from fluorescent lights may cause nuisance alarms. Install smoke alarms at least 5 feet (1.5 meters) from such lights.
• In “dead air” spaces. “Dead air spaces my prevent smoke from reaching the smoke alarm.
Avoiding Dead Air Spaces
“Dead air” spaces may prevent smoke from reaching the Smoke Alarm. To avoid dead air spaces, follow the installation recommendations below.
On ceilings, install Smoke Alarms as close to the center of the ceiling as possible. If this is not possible, install the Smoke Alarm at least 4 inches (100 mm) from the wall or corner.
For wall ounting (if allowed by building codes), the top edge of Smoke Alarms should be placed between 4 and 12 inches (100 and 300 mm) from the wall/ceiling line, below typical
“dead air” spaces.
On a peaked, gabled, or cathedral ceiling, install the first Smoke Alarm within 3 feet (0.9 meters) of the peak of the ceiling, measured horizontally. Additional Smoke Alarms may be
required depending on the length, angle, ect of the ceilings slope. Refer to FPA 72 for details on requirements for sloped peaked ceilings.
WARNING
: ever remove the battery from the Smoke Alarm to stop a nuisance alarm. Open a window or fan the air around the Smoke Alarm to get rid of the smoke. The alarm will turn itself
off when the smoke is gone. If nuisance alarms persist, attempt to clean the Smoke Alarm as described in the User's Manual.
WARNING:
Do not stand close to the Smoke Alarm when the alarm is sounding. The alarm is loud in order to wake you in an emergency. Too much exposure to the horn at close range may be
harmful to your hearing.
LIMITATIONS OF SMOKE ALARMS
Smoke Alarms have played a key role in reducing deaths resulting from home fires worldwide. However, like any warning device, Smoke Alarms can only work if they are properly located, installed,
and maintained, and if smoke reaches them. They are not foolproof.
• S oke Alar s ay not waken all individuals. Current studies have shown smoke alarms may not awaken all sleeping individuals, and that it is the responsibility of individuals in the
household that are capable of assisting others to provide assistance to those who may not be awakened by the alarm sound, or to those who may be incapable of safely evacuating the
area unassisted.
• S oke Alar s cannot work without power. Battery operated units cannot work if the batteries are missing, disconnected or dead, if the wrong type of batteries are used, or if the
batteries are not installed correctly. AC units cannot work if the AC power is cut off for any reason (open fuse or circuit breaker, failure along a power line or a power station, electrical
fire that burns the electrical wires, ect.). If you are concerned about the limitations of battery or AC power, install both types of units.
• S oke Alar s cannon detect fires if the s oke does not reach the . Smoke from fires in chimneys or walls, on roofs, or on the other side of closed doors may not reach the sensing
chamber and set off the alarm. That is why one unit should be installed inside each bedroom or sleeping area. Especially if bedroom or sleeping area doors are closed at night and the in
the hallway between them.
• S oke Alar s ay not detect fire on another floor or area of the ho e. For example, a stand-alone unit on the second floor may not detect smoke from a basement fire until the fire
spreads. This may not give you enough time to escape safely. That is why recommended minimum protection is at least one unit in every sleeping area, and every bedroom on every
level of your home. Even with a unit on every floor, stand-alone units may not provide as much protection as interconnected units, especially if the fire starts in a remote area. Some
safety experts recommend installing interconnected AC powered units with battery back-up or professional fire detection systems, so if one unit senses smoke, all units alarm.
Interconnected units may provide earlier warning than stand-alone units since all units alarm when one detects smoke.
• S oke Alar s ay not be heard. Though the alarm horn in this unit meets or exceeds current standards, it may not be heard if:
1. The unit is located outside a closed or partially closed door.
2. Residents recently consumed alcohol or drugs.
3. The alarm is drowned out by noise from stereo, TV, traffic, air conditioners or other appliances.
4. Residents are hearing impaired or sound sleepers. Special purpose units, like those with visual and audible alarms, should be installed for hearing impaired residents.
• S oke Alar s ay not have ti e to alar before the fire itself causes da age, injury, or death, since s oke fro so e fires ay not reach the unit i ediately. Exa ples of
this include persons s oking in bed, children playing with atches, or fires caused by violent explosions resulting fro escaping gas.
• S oke Alar s are not foolproof. Like any electronic device, Smoke Alarms are made of components that can wear out or fail at any time. You must test the unit weekly to ensure your
continued protection. Smoke Alarms cannot prevent or extinguish fires. They are not a substitute for property or life insurance.
• S oke Alar s have a li ited life. The unit should be replaced immediately if it is not operating properly. You should always replace a Smoke Alarm after 10 years from date of
purchase. Write the purchase date on the back of the unit.
• S oke Alar trans itter li itations. Radio signals transmitted by this smoke alarm may be blocked or reflected by metal objects. Adjacent devices or systems using radio signals may
interfere with the operation of this alarm. Test the system weekly to ensure signals are transmitted and received properly.
TIPS TO ENHANCE YOUR PROTECTION FROM FIRES
Putting up smoke alarms is only one step in protecting your family from fires. You must also reduce the chances that fires will start in your home. You must also increase your chances of escaping
safely if one does start. To have a good fire safety program you must apply the following tips to enhance your family's protection from fires.
• Install Smoke Alarms properly. Carefully follow all the instructions in this manual. Keep your smoke alarm clean, and test them every week.
• Remember that Smoke Alarms that do not work will not alert you. Replace your Smoke Alarms immediately if they are not working properly.
• Follow fire safety rules, and prevent hazardous situations:
◦
Use smoking materials properly. ever smoke in bed.
◦
Keep matches and cigarette lighters away from children.
◦
Store flammable materials in proper containers. ever use them near open flame or sparks.
◦
Keep electrical appliances in good condition. Do not overload electrical circuits.
◦
Keep stoves, fireplaces, chimneys, and barbecue grills grease free. Make sure they are properly installed and away from any combustible materials.
◦
Keep portable heaters and open flames such as candles away from combustible materials.
◦
Do not allow rubbish to accumulate.
◦
Keep a supply of extra batteries on hand for your battery powered Smoke Alarms.
• Develop a family escape plan and practice it with your entire family. Be sure to include small children in your practice.
• Draw a floor plan of your home, and find two ways to exit from each room. There should be one way to get out of each bedroom without opening the door.
• Explain to children what the Smoke Alarm's alarm signal means. Teach them that they must be prepared to leave the home by themselves if necessary. Show them how to check to see if
doors are hot before opening them. Show them how to stay close to the floor and crawl if necessary. Show them how to use alternate exit if the door is hot and should not be opened.
• Decide on a meeting place which has a safe distance from your house. Make sure that all your children understand that they should go and wait for you there if there is a fire.
• Hold fire drills at least every 6 months to make sure that everyone, even small children, knows what to do to escape safely.
• Know where to go to call the Fire Department from outside your home.
Page
6
of
6
3/23/15
24-Hour Tech Support Line: (715)808-0164
www.ResolutionProducts.com
• Provide emergency equipment, such as fire extinguishers, and teach your family to use this equipment properly.
TIPS TO FACE A FIRE IN YOUR HOME
If you have made a family escape plan and practiced it with your family, you have increased their chances of escaping safely. Go over the following rules with your children each time you have fire
drills. This will help everyone remember them in case of a real fire emergency.
• Don't panic and stay calm. Your safe escape may depend on thinking clearly and remembering what you have practiced.
• Get out of the house as quickly as possible. Follow a planned escape route. Do not stop to collect anything or to get dressed.
• Feel the doors to see if they are hot. If they are not, open them carefully. Do not open a door if it is hot. Use an alternate escape route.
• Stay close to the floor. Smoke and hot gases rise.
• Cover your nose and mouth with a wet or damp cloth. Take a short, shallow breaths.
• Keep door and windows closed. Open them only if you have to in order to escape.
• Meet at your planned meeting place after leaving the house.
• Call the Fire Department as soon as possible from outside your house. Give the address and your name.
• ever go back inside a burning building. Contact your local Fire Department. They will give you more ideas about how to make your home safer from fires and how to plan your family's
escape.
AGENCY PLACEMENT RECOMMENDATIONS
NFPA 72 Chapter 29
S oke alar s should be installed in accordance with the NFPA Standard 72 (National Fire Protection Association, Battery arch Part, Quincy, MA 02269)
For your information, the ational Fire Alarm and Signaling Code, FPA 72 reads as follows.
“29.5.1* Required Detection.”
“29.5.1.1* Where required by other governing laws, codes, or standards for a specific type of occupancy, approved single and multiple-station smoke alarms shall be installed as follows:
(1)*In all sleeping rooms and guest rooms
(2)*Outside of each separate dwelling unit sleeping area, within 21 ft (6.4 m) of any door to a sleeping room, with the distance measured along a path of travel
(3) On every level of a dwelling unit, including basements
(4) On every level of a residential board and care occupancy (small facility), including basements and excluding crawl spaces and unfinished attics
(5)*In the living area(s) of a guest suite
(6) In the living area(s) of a residential board and care occupancy (small facility) “
(Reprinted with permission from FPA 72®, ational Fire Alarm & Signaling Code Copyright © 2013 ational Fire Protection Association, Quincy, MA 02269. This reprinted material is not the complete
and official position of the ational Fire Protection Association, on the referenced subject which is represented only by the standards in its entirety.) ( ational Fire Alarm & Signaling Code ® and FPA
72 ® are registered trademarks of the ational Fire Protection Association, Inc., Quincy, MA 02269.)
California State Fire Mar hal (CSFM)
As stated by the California State Fire Marshal “Early warning detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows: A Smoke
Alarm installed in each separate sleeping area (in the vicinity of, but outside of the bedrooms), and heat or smoke detectors in the living rooms, dining rooms, bedrooms, kitchens, hallways, attics,
furnace rooms, closets, utility and storage rooms, basements and attached garages”
NOTE
Specific requirements for Smoke Alarm installation vary from state to state and from region to region. Check with your local Fire Department for current requirements in your area.
SPECIAL COMPLIANCE CONSIDERATIONS
This smoke alarm is designed for use in a single residential unit only, which means it should be used inside a single family home or apartment. It is not meant to be used in common areas like lobbies,
hallways, or another apartment in a multi-family building, unless there are already working alarms in each family unit. Smoke alarms placed in common areas outside of the individual living unit,
such as on porches or in hallways, may not provide early warning to residents. In multi-family buildings each family living unit should setup its own smoke alarms.
This alarm is not meant to be used in non-residential buildings. Warehouses, industrial or commercial buildings, and special purpose non-residential buildings require special fire detection and alarm
systems. This smoke alarm alone is not a suitable substitute for complete fire detection systems for places where many people live or work, such as hotels or motels. The same is true of dormitories,
hospitals, nursing homes or group homes of any kind, even if they were once single family homes.
Refer to FPA 72 ( ational Fire Alarm and Signaling Code) and FPA 101 (Life Safety Code), local building codes or consult your Fire Department for detailed fire protection requirements in buildings
not defined as “households”.
NOTICES
Warranty
Resolution Products, Inc. will replace products that are defective in their first five (5) years.
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference that may be received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the Resolution Products, Inc. could void the user's authority to operate this equipment.
FCC ID: U5X-RE312
IC Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux C R d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1)l'appareil ne doit pas produire de brouillage, et
(2)l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
IC: 8310A-RE312
Manual: 47-0001-08 Rev A
Popular Smoke Alarm manuals by other brands

Jalo Helsinki
Jalo Helsinki Kupu Series Installation

Panasonic
Panasonic EBL512 Specification sheet

Bosch
Bosch F220 B6 manual

System Sensor
System Sensor B210LP Installation and maintenance instructions

System Sensor
System Sensor 2412 Installation and maintenance instructions

Hochiki
Hochiki SLR-24 installation instructions

Heatit
Heatit Z-SMOKE Installer manual

Securiton
Securiton ASD 532 maintenance

Deltronic Security
Deltronic Security Numens 205 Series user manual

System Sensor
System Sensor PERTRONIC Innovair flex D4120 Installation and maintenance instructions

Honeywell
Honeywell SS4-AS Installation guide and operating manual

mumbi
mumbi m-RMAG user manual