Optical Systems Design OSD2512 User manual

Quick Start Guide
OSD2512
MANAGED 12 x 10/100/1000BASE-T (RJ45)
AND 2 x 1G (SFP) ETHERNET SWITCH

OPTICAL SYSTEMS DESIGN
DOC ID: 10116701
OSD2512 QUICK START GUIDE
PAGE 3
INDEX 1
1 INTRODUCTION ...................................................................................................................... 4
2 INSTALLATION........................................................................................................................ 4
3 OSD2512 FRONT AND REAR PANELS................................................................................. 5
3.1 FRONT PANEL ....................................................................................................................... 5
3.2 REAR P ANEL ............................................................................................................................ 5
4 POWER SUPPLY CONNECTIONS ........................................................................................ 6
5 LED INDICATORS ................................................................................................................... 7
6 FITTING SFP CONNECTORS ................................................................................................ 8
7 CLI OVERVIEW ....................................................................................................................... 9
7.1 C ONNECT TO CLI ...................................................................................................................... 9
7.2 CLI COMMAND FOR IP C ONFIGURATION ................................................................................. 10
8 GUI OVERVIEW ..................................................................................................................... 11
8.1 D EFAULT S ETTING ................................................................................................................... 11
8.2 L OG INTO THE S WITCH ............................................................................................................ 11
8.3 IP C ONFIGURATION ................................................................................................................. 11
8.4 U SERS A UTHENTICATION ........................................................................................................ 12
8.5 S AVE C ONFIGURATION TO S TART - UP ...................................................................................... 13
9 WARRANTY ............................................................................................................................ 14
9.1 WARRANTY PERIOD.......................................................................................................... 14
9.2 REPAIRS................................................................................................................................ 14
9.2.1 WARRANTY REPAIRS.................................................................................................... 14
9.2.2 OUT-OF-WARRANTY REPAIRS.................................................................................... 14
9.2.3 SITE REPAIRS .................................................................................................................. 14
9.2.4 EXCLUSIONS ................................................................................................................... 14
FIGURE 1: FRONT PANEL.................................................................................................................... 5
FIGURE 2: REAR PANEL ...................................................................................................................... 5
FIGURE 3: POWER CONNECTION...................................................................................................... 6
FIGURE 4: FITTING/REMOVING SFP CONNECTORS ..................................................................... 8
TABLE 1: DC POWER CONNECTION................................................................................................. 6
TABLE 2: LED FUNCTION ................................................................................................................... 7

OPTICAL SYSTEMS DESIGN
DOC ID: 10116701
OSD2512 QUICK START GUIDE
PAGE 4
1INTRODUCTION
Thank you for choosing the OSD2512 14-Port Gigabit Managed Ethernet Switch. This Quick Start
Guide is designed to guide you through the installation and basic software function.
2INSTALLATION
ELECTROMAGNETIC COMPATIBILITY
WARNING: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
OPTICAL OUTPUT OPERATION
WARNING: Laser Safety: Class 1 Laser Product (SFP) per IEC 60825-1:2014 standard.
Class 1
The OSD2512 is a Class 1 laser product.
PRECAUTIONS
▲ All service personnel should be provided training as to the hazards of direct viewing of laser
radiation and of the precautionary measures during servicing of equipment
▲ Areas where laser products are installed should be restricted in access to trained service
personnel only and appropriate warning signs posted in the work area.
▲ All laser apertures should be covered by protective covers when not connected to optical
fibers. Never leave outputs uncovered.
▲ Laser equipment should be positioned above or below eye level where possible. Apertures
should be positioned away from personnel.
▲ Protective eyewear should be worn in the vicinity of laser equipment.

OPTICAL SYSTEMS DESIGN
DOC ID: 10116701
OSD2512 QUICK START GUIDE
PAGE 5
3OSD2512 FRONT AND REAR PANELS
3.1 FRONT PANEL
FIGURE 1: FRONT PANEL
1. Board Status LED
2. USB Console Port
3. View LED Mode Button
4. View Mode LEDs Indicators
5. Copper Port Status LEDs
6. RJ45 Copper Ports
7. SFP Fiber LED
8. SFP Fiber Ports
9. SFP Fiber LED
10. Reset Button
3.2 REAR PANEL
FIGURE 2: REAR PANEL
11. Earth
12. Power 1 LED
13. Dual Redundant Power Input
14. Power 2 LED
1 2 3 4 5 6 7 8 9 10
11 12 13 14

OPTICAL SYSTEMS DESIGN
DOC ID: 10116701
OSD2512 QUICK START GUIDE
PAGE 6
4Power Supply Connections
Connect the dual redundant power to the 4-way terminal block located on the rear of the unit.
The OSD2512 requires external +10 to +36V
DC
@ 40VA Max power.
FIGURE 3: POWER CONNECTION
TABLE 1: DC POWER CONNECTION
External Power Pin Specification
Pin 1, Pin 3 0V (Ground Isolated)
Pin 2, Pin 4 +10 to +36V
DC
@ 40VA max

OPTICAL SYSTEMS DESIGN
DOC ID: 10116701
OSD2512 QUICK START GUIDE
PAGE 7
5LED Indicators
TABLE 2: LED FUNCTION
Function
Board Status LED
• Green – Normal status
• Red Blinking – Internal Warning
View Mode LED
Indicators
Controlled y View LED Mode Button. Pressing the Mode utton
cycles
the Copper Port Status LED indication.
Speed Mode  Duplex Mode  Status Mode  Reserved .
Copper Port
Status LED
The
Copper
Port Status LED will indicate
different information.
Speed Mode:
• Green – 1G ps
• Yellow – 100MBps
• Off – No Connection
• Blinking - Traffic
Duplex Mode:
• Green – Full Duplex
• Yellow – Half Duplex
• Off – No Connection
• Blinking - Traffic
Status Mode:
• Green – Connection good
• Off – No Connection
Fi er Port Status
LED
• Green – 1G ps
• Off – No Connection
• Blinking - Traffic

OPTICAL SYSTEMS DESIGN
DOC ID: 10116701
OSD2512 QUICK START GUIDE
PAGE 8
6Fitting SFP Connectors
Care should be taken when inserting/removing the SFP connectors from the SFP port as SFP modules
are Electrostatic (ES) sensitive and Electrostatic Discharge (ESD) precautions should be taken when
installing. Ensure that the SFP is fully engaged and latched into position.
Inserting SFP – Ensure that the SFP lever is in the locked position and insert into appropriate SFP
port. Gently push the SFP until it locks into place. Remove plastic/rubber dust cap and fit appropriate
fiber cable.
Removing SFP – Remove fiber connector. Pull the SFP lever down to unlock SFP from housing.
Using the lever, gently pull the SFP out.
Fiber SFP
FIGURE 4: FITTING/REMOVING SFP CONNECTORS
Inserting
SFP
Removing
SFP
1
2

OPTICAL SYSTEMS DESIGN
DOC ID: 10116701
OSD2512 QUICK START GUIDE
PAGE 9
7CLI OVERVIEW
7.1 CONNECT TO CLI
The Silicon Laboratories CP210x VCP Drivers is needed to be installed on the PC before connecting
the switch.

OPTICAL SYSTEMS DESIGN
DOC ID: 10116701
OSD2512 QUICK START GUIDE
PAGE 10
1. Connect the Console Port on UUT to PC with USB cable (Type A to Type B).
2. Using HyperTerminal to set up the following parameters.
•Baud Rate: 115200
•Data Bits: 8
•Parity: None
•Stop Bits: 1
•Flow Control: None
3. Check the link by pressing <ENTER>. The line should jump to the next line.
4. Using the Username and password to login the switch
•Default Username: admin
•Default Password: (None)
7.2 CLI COMMAND FOR IP CONFIGURATION
•show ip interface brief:Display the current IP address and subnet mask.
•configure terminal -> interface vlan 1 -> ip address <IP address> <subnet mask>: Setup the
switch IP address.
•copy running-config startup- config: Save the current configuration to start-up configuration.
PS: All configuration changes must be saved otherwise all the changes will be lost after
rebooting!

OPTICAL SYSTEMS DESIGN
DOC ID: 10116701
OSD2512 QUICK START GUIDE
PAGE 11
8GUI Overview
8.1 DEFAULT SETTING
• IP Address: 192.168.0.99
• Subnet Mask: 255.255.255.0
• Gateway: 192.168.0.1
• User Name: admin
• Password: (None)
8.2 LOG INTO THE SWITCH
• Connect a switch port to a PC, Change the PC’s network IP address to connect to the switch
(i.e.: 192.168.0.2).
• In a web browser, enter the URL 192.168.0.99.
• Enter the username and password.
8.3 IP CONFIGURATION
In the treemap on the left, expand the Configuration -> System -> IP.
Enter the IPv4 address and Mask Length in the table.
Choose the management VLAN ID to access that IP in VLAN table if VLAN function is required.
If the multiple IP addresses are required, click Add Interface to add more IP interface.
Click Save to save the configuration.
Use new IP address to access the switch.
PS: All configuration changes must be saved otherwise all the changes will be lost after
rebooting!

OPTICAL SYSTEMS DESIGN
DOC ID: 10116701
OSD2512 QUICK START GUIDE
PAGE 12
8.4 USERS AUTHENTICATION
In the tree map on the left, expand the Configuration -> Security-> Switch-> Users
Click admin to change the current admin account setting.
If multiple users are required, click Add New User

OPTICAL SYSTEMS DESIGN
DOC ID: 10116701
OSD2512 QUICK START GUIDE
PAGE 13
PS: All configuration changes must be saved otherwise all the changes will be lost after
rebooting!
8.5 SAVE CONFIGURATION TO START-UP
In the treemap below, expand the Maintenance and expand Configuration, then select Save startup-
config
Click Save Configuration to save the configuration on start-up.

OPTICAL SYSTEMS DESIGN
DOC ID: 10116701
OSD2512 QUICK START GUIDE
PAGE 14
9WARRANTY
Thank you for purchasing equipment designed, manufactured and serviced by Optical Systems Design
(OSD). OSD warrants that at the time of shipment, its products are free from defects in material and
workmanship and conforms to specifications. Our Warranty conditions are outlined below:
9.1 WARRANTY PERIOD
For warranty period, please call your local OSD distributor.
9.2 REPAIRS
Optical Systems Design reserves the right to repair or replace faulty modules/units. Please obtain a
“Return Material Authorisation” (RMA) form and number before returning goods.
Goods must be returned in adequate packing material to Optical Systems Design, Warriewood or its
nominated authorised representative, for all repairs.
9.2.1 WARRANTY REPAIRS
Return shipments to OSD shall be at customer's expense and freight back to the customer will be at
OSD expense.
9.2.2 OUT-OF-WARRANTY REPAIRS
OSD reserves the right to repair or replace any faulty goods. Freight costs and insurance for both
journeys are met by the user. All equipment repaired by OSD will have a 3-Month Warranty from the
date of dispatch.
9.2.3 SITE REPAIRS
By agreement site repairs may be undertaken for which out of pocket, hotel and travel expenses will be
charged.
9.2.4 EXCLUSIONS
This warranty does not apply to defects caused by unauthorized modifications, misuse, abuse or
transport damage to the equipment. All modifications to OSD’s standard product will need written
authorization and will be charged at normal repair rates. All modifications are to be carried out by OSD
Technicians. Warranty is void if unauthorized removal and/or tampering with serial number and/or
repair labels is evident.

OPTICAL SYSTEMS DESIGN
DOC ID: 10116701
OSD2512 QUICK START GUIDE
PAGE 15

Optical Systems Design Pty. Ltd.
7/1 Vuko Pl. Warriewood 2102
P.O. Box 891 Mona Vale
N.S.W. Australia 2103
Telephone: [phone]
Facsimile: [phone]
Email: [email protected]m.au
Web Site: www.osd.com.au
OPTIC L
SYSTEMS
DESIGN
PTY LTD A.B.N. 83 003 020 504
Printed in Australia