Optiview HDB3MVF User manual

904-805-1581
HDB3MVF/HDB2MVF
HD IR Waterproof Fixed Network Camera
（With Integrated Bracket）
User’s Manual

2
Version 3.5.0

i
Welcome
Thank you for purchasing our network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

ii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1. This series product cannot support these
two modes at the same time.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.

iii
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name
Amount
Network Camera Unit
1
Quick Start Guide
1
Installation Accessories Bag
1
12V to 24V Conversion Cable
(For AC 24V series product only)
1
CD
1

iv
Table of Contents
1General Introduction ..................................................................................................................1
1.1 Overview........................................................................................................................1
1.2 Features.........................................................................................................................1
1.3 Specifications................................................................................................................2
1.3.1 Performance...........................................................................................................2
1.3.2 Factory Default Setup...........................................................................................4
2Structure ....................................................................................................................................13
2.1 Multiple-function Combination Cable ......................................................................13
2.2 Framework and Dimension.......................................................................................14
2.3 Bidirectional talk..........................................................................................................15
2.3.1 Device-end to PC-end........................................................................................15
2.3.2 PC-end to the Device-end..................................................................................15
2.4 Alarm Setup.................................................................................................................15
3Installation..................................................................................................................................17
3.1 Device Installation ......................................................................................................17
3.2 SD Card Installation ...................................................................................................18
3.3 Lens Adjustment.........................................................................................................19
3.4 Bracket Adjustment....................................................................................................19
3.5 OSD Buttons (For Motorized Zoom Lens Series Product Only) .........................20
4Quick Configuration Tool.........................................................................................................22
4.1 Overview......................................................................................................................22
4.2 Operation .....................................................................................................................22
5Web Operation..........................................................................................................................25

v
5.1 Network Connection...................................................................................................25
5.2 Login and Logout........................................................................................................25
6FAQ ............................................................................................................................................28
Appendix Toxic or Hazardous Materials or Elements ...............................................................29

1
1General Introduction
1.1 Overview
This series network camera integrates the traditional camera and network video technology. It adopts
audio and video data collection, transmission together. It can connect to the network directly without
any auxiliary device.
This series network camera product uses standard H.264 video compression technology and G.711a
audio compression technology, which maximally guarantee the audio and video quality.
It supports the IR night vision function. In the night environments, the device can use the IR light to
highlight the object which is suitable for the surveillance function in the low illumination environments.
The built-in protection enclosure and waterproof design conforms to the IP 66 level. It has the sound
waterproof function suitable for use in the outdoor environments.
It supports real-time monitor and listening at the same time. It supports analog video output and dual-
way bidirectional talk.
It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Due to its multiple functions and various uses, this series
network camera is widely used in many environments such office, bank, road monitor and etc.
1.2 Features
User
Management
Different user rights for each group, one user belongs to one group.
The user right shall not exceed the group right.
Storage
Function
Support central server backup function in accordance with your configuration and
setup in alarm or schedule setting
Support record via Web and the recorded file are storage in the client-end PC.
Support built-in SD card.
Do not support local SD card hot swap storage function. Support short-time
storage when encounter disconnection.
Support network storage function such as FTP.
Alarm
Function
Real-time respond to external on-off alarm input, and video detect as user pre-
defined activation setup and generate corresponding message in screen and
audio prompt(allow user to pre-record audio file)
Real-time video detect: motion detect, camera masking.
Network
Monitor
Network camera supports one-channel audio/video data transmit to network
terminal and then decode. Delay is within 270ms (network bandwidth support
needed)
Max supports 20 connections.
Adopt the following audio and video transmission protocol: HTTP, TCP, UDP,
MULTICAST, RTP/RTCP, RTSP and etc.
Support web access.
Network
Management
Realize network camera configuration and management via Ethernet.
Support device management via web or client-end.
Power
External power adapter DC12V/AC 24V. You can select according to your actual
environments. Please note system can not support these two types of power
supplying at the same time.
Assistant
Function
Log function
Support system resource information and running status real-time display.

2
Day/Night mode auto switch.
Built-in IR light. Support IR night vision.
Support picture parameter setup such as electronic shutter and gain setup.
Backlight compensation: screen auto split to realize backlight compensation to
adjust the bright.
Support video watermark function to avoid vicious video modification.
The enclosure conforms to the IP 66 protection. Has the waterproof function.
1.3 Specifications
1.3.1 Performance
Please refer to the following sheet for network camera performance specification.
Model
Parameter
HDB3MVF
HDB2MVF
System
Main
Processor
TI Davinci high performance DSP
OS
Embedded LINUX
System
Resources
Support real-time network, local record, and remote operation at the same
time.
User
Interface
Remote operation interface such as WEB, Hybrid NDVR, CMS Client
System
Status
SD card status, bit stream statistics, log, and software version.
Video Parameter
Image
Sensor
1/2.8-inch CMOS
1/3-inch CMOS
Pixel
2096(H)x1561(V)
1920(H)*1080(V)
Day/Night
Mode
Support day/night mode switch and IR-CUT at the same time. (The lens has
built-in IR-CUT mechanical component.).
Auto
Aperture
DC drive
Gain Control
Fixed/Auto
White
Balance
Auto
BLC
On/Off
Exposure
Mode
Manual/Auto
PAL: It ranges from 1/3 to 1/10000
NTSC: It ranges from 1/4 to 1/10000
Video
Compressio
n Standard
H.264/ H.264B/MJPEG
Video Frame
Rate
PAL:
Main stream
3M(1~20fps)/1080P/720P(1 ~
25fps)
Extra stream
D1/CIF(1 ~ 25fps)
PAL:
Main stream:
1080P(1920×1080)/ 720P(1280×720)/
D1(704×576)/ CIF(352×288)
Extra stream:
1080P/720P(1 ~ 25/30fps)
NTSC:
Main stream
3M(1~20fps)/1080P/720P(1 ~
30fps)
Extra stream
D1/CIF(1 ~ 30fps)
NTSC:
Main stream:
1080P(1920×1080)/720P(1 ~ 25/30fps)
Extra stream:
D1/CIF(1 ~ 25/30fps)
Video Bit
Rate
H.264: 32Kbps-8192Kbps.
MJPEG: 32K ~ 24576Kbps
Support customized setup.
H.264: 32K ~ 8192Kbps, MJPEG: 32K ~
20480Kbps,
Support customized setup.
Video Flip
Support mirror.

3
Support flip function.
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy
Mask
Supports max 4 privacy mask zones
Video Setup
Support parameter setup such as bright, contrast.
Video
Information
Channel title, time title, motion detect, camera masking.
Lens
Motorized zoom 3.3-
12[email protected]
Motorized zoom 3.3-12[email protected]
Lens
Interface
Φ14 interface. Lens is the default accessories
Audio
Audio Input
1-channel. RCA
Audio
Output
1-channel. RCA
Bidirectional
Talk Input
Reuse the first audio input channel
Audio Bit
Rate
16kbps 16BIT
Audio
Compressio
n Standard
G.711a/G.711u/PCM
Video
Motion
Detect
396 (18*22) detection zones；sensitivity level ranges from 1 to 6 (The 6th
level has the highest sensitivity)
Activation event: alarm device, audio/video storage, image snapshot, log,
email function and etc.
Alarm Input
2-channel input，1-channel output
Record and Backup
Record
Priority
Manual>External alarm >Video detect>Schedule
Local
Storage
Support Micro SD card storage
Storage
Managemen
t
Support display local storage status
Network
Wire
Network
1-channel wire Ethernet port, 10/100 Base-T Ethernet
Network
Protocol
Standard HTTP, TCP/IP, ARP, IGMP, ICMP, RTSP, RTP,UDP, RTCP,
SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour, SNMP.
Remote
Operation
Monitor, PTZ control, system setup, file download, log information,
maintenance , upgrade and etc.
AUX
Interface
Video
Output
1-channel analog video output，BNC port.
Restore
Default
Setup
Reset button
Power
DC12V(AC24 optional), PoE(802.3af)
General
Parameter
Power
Consumptio
n
8W MAX (10W MAX when ICR switch)
Working
Temperature
-10℃~+60℃
Working
Humidify
10%~90%
Dimensions(
mm)
φ104*306.7

4
Weight
1250g（Excluding box）
Installation
Bracket is included in the accessories bag.
IR Distance
20~30m
Protection
Level
IP66
1.3.2 Factory Default Setup
Please refer to the following sheet for factory default setup information.
Setup
Item
Default Setup
HDB3MVF
HDB2MVF
Camera
Conditions
Brightness
50
Contrast
50
Saturation
50
Sharpness
50
Gain Adjust
0-50
Exposure Mode
Auto
Auto Iris
On
Scene Mode
Auto
Day/night Mode
Auto
BLC
Off
Mirror
Off
Flip
Off
Video
Video bit stream
Main
Stre
am
Bit
stream
type
General
Encode
mode
H.264
Resolut
ion
3.0M(2048*1536)
1080P（1920*1080）
Frame
Rate
（FPS
）
PAL:25
NTSC:30
Bit
Rate
Type
VBR/CBR
Recom
mende
d Bit
3584-8192 Kb/S
Bit
Rate
8192
I
Frame
50
Water
mark
Enable
Water
mark
charact
DigitalCCTV

5
Setup
Item
Default Setup
HDB3MVF
HDB2MVF
er
Sub
Stre
am
Enable
Enable
Bit
stream
type
General
Encod
e
mode
H.264
Resolu
tion
D1/CIF(1 ~ 25/30fps)
Frame
Rate
（FPS
）
PAL:25
NTSC:30
Bit
Rate
Type
VBR/CBR
Recom
mende
d Bit
192-1024Kb/S
Bit
Rate
1024
I
Frame
50
Snapshot
Snaps
hot
Type
General
Image
Size
3M(2048*1536)
1080P（1920*1080）
Qualit
y
5
Interva
l
1s
Video
Overlay
Privac
y
Mask
Disable
Chann
el Title
Enable
Time
Title
Enable
Path
Snapsh
ot Path
C:\PictureDownload
Record
Path
C:\RecordDownload
Audio
Main
Stream
Enable
Enable
Encode
Mode
G.711A

6
Setup
Item
Default Setup
HDB3MVF
HDB2MVF
Sub
Stream
Enable
Disable
Encode
Mode
G.711A
Network
TCP/IP
Host
Name
IPC
Ethern
et Card
Wire(Default)
Mode
Static
Mac
Addres
s
Device MAC address when it is shipped out of the factory
IP
Version
IPV4/IPV6
IP
Addres
s
192.168.1.108
Subnet
Mask
255.255.255.0
Default
Gatew
ay
192.168.1.1
Preferr
ed
DNS
8.8.8.8
Alterna
te DNS
8.8.8.8
Enable
ARP/Pi
ng set
device
IP
addres
s
service
Enable
Connecti
on
Max
Conne
ction
10
TCP
Port
37777
UDP
Port
37778
HTTP
Port
80
RTSP
Port
554
HTTPS
Port
443
PPPoE
Enable
Disable

7
Setup
Item
Default Setup
HDB3MVF
HDB2MVF
Userna
me
none
Passw
ord
N/A
DDNS
Server
Type
Disable，CN99 DDNS
Server
IP
none
Server
Port
80
Domai
n
Name
none
User
none
Passw
ord
****
Update
Period
10 minutes
IP Filter
Trusted
sites
Disable
SMTP(E
mail)
SMTP
Server
none
Port
25
Anony
mity
Disable
User
Name
anonymity
Passw
ord
****
Sender
none
Authen
tication
(Encry
ption
mode)
N/A
Title
(Subjec
t)
IPC Message
Attach
ment
N/A
Mail
Receiv
er
0 seconds
Email
Disable，interval=60 minutes

8
Setup
Item
Default Setup
HDB3MVF
HDB2MVF
Test
UPnP
Enable
UPnP
Disable
SNMP
SNMP
v1
Disable
SNMP
v2
Disable
SNMP
v3
Disable
SNMP
Port
161
Read
Comm
unity
public
Write
Comm
unity
private
Trap
Addres
s
N/A
Trap
Port
162
Bonjour
Enable
Enable
Server
Name
MAC
Multicast
Multica
st
Addres
s
239.255.42.42
Port
36666
QoS
Real-
time
Monitor
0
Comm
and
0
Event
Video detect
Motion
Detect
Enable
Disable
Anti-
dither
5 seconds
Sensiti
vity
3
Record
Chann
el
Enable
Record
Delay
10 seconds
Relay
out
Enable

9
Setup
Item
Default Setup
HDB3MVF
HDB2MVF
Alarm
Delay
10 seconds
Send
Email
Disable
Snapsh
ot
Disable
Video
Masking
Enable
Disable
Record
Chann
el
Enable
Record
Delay
10 seconds
Relay
out
Enable
Record
Delay
10 seconds
Send
Email
Disable
Snapsh
ot
Disable
Alarm
Alarm
Activati
on
Enable
Disable
Relay
in
Alarm 1
Anti-
dither
0 seconds
Sensor
Type
NO
Record
Chann
el
Enable
Record
Delay
10 seconds
Relay
out
Enable
Alarm
Delay
10 seconds
Send
Email
Disable
Snapsh
ot
Disable
Relay output
1
Abnormity
No SD
Card
Enable
Disable
Relay
out
Enable
Relay
out
Delay
10 seconds

10
Setup
Item
Default Setup
HDB3MVF
HDB2MVF
Send
email
Disable
Capacit
y
Warning
Enable
Disable
Capacit
y Limit
10%
Relay
out
Enable
Relay
out
Delay
10 seconds
Send
Email
Disable
SD
Card
Error
Enable
Disable
Relay
out
Enable
Relay
out
Delay
10 seconds
Send
email
Disable
Disconn
ection
Enable
Disable
Record
Enable
Record
Delay
10 seconds
Relay
out
Enable
Relay
out
Delay
10 seconds
IP
Conflict
Enable
Disable
Record
Enable
Record
Delay
10 seconds
Relay
out
Enable
Relay
out
Delay
10 seconds
Storage
Storage
FTP
Enable
FTP
Disable
Server
IP
N/A
Port
21
Userna
me
anonymity
Passw
N/A

11
Setup
Item
Default Setup
HDB3MVF
HDB2MVF
ord
Remot
e path
share
Emerg
ency
(Local)
Disable
Record
Control
Pack
Duratio
n
8 minutes
Pre-
record
5 seconds
Disk
Full
Overwrite
Record
Mode
Auto
Record
Stream
Main stream
System
General
Local
Host
Device
No
Device MAC
Langua
ge
English
Video
Standa
rd
PAL
Date
and
time
Date
Format
Y-M-D
Time
Format
24H
Time
Zone
GMT+08:00
System
Time
Sync
DST
Disable
DST
Type
Week
Start
Time
00:00:00 of the first Sunday of the month
End
Time
00:00:00 of the second Monday of the month
NTP
Disable
NTP
Server
clock.isc.org
Port
37
Update
Period
10 minutes
Auto
Auto
Enable

12
Setup
Item
Default Setup
HDB3MVF
HDB2MVF
Maintena
nce
Reboot
Auto
Delete
Old
Files
Disable

13
2Structure
2.1 Multiple-function Combination Cable
You can refer to the following figure for multiple-function combination cable information. See Figure
2-1.
Figure 2-1
Please refer to the following sheet for detailed information.
SN
Port Name
Function
Connection
Note
1
DC 12V/AC
24V
Power input
port
/
Power port. Input DC 12V/AC 24V (Please
use the provided conversion cable)
2
Reset
Reset port
/
Hardware reset function. Press it for 3 to 5
seconds; system hardware can restore
default setup.
3
I/O
I/O port
/
Connect to I/O port.
4
LAN
Network port
Ethernet
port
Connect to standard Ethernet cable.
5
AUDIO IN
Audio input
port
RCA
Input audio signal. It can receive the analog
audio signal from the pickup.
6
AUDIO OUT
Audio output
port
RCA
Output audio signal to the devices such as
the sound box.
7
VIDEO OUT
Video output
port
BNC
Output analog video signal. It can connect to
the TV monitor to view the video.
Please refer to the follow sheet for detailed I/O port information.