Optoma BT16063 User manual

Optoma remote control operating manual
Product Name: Remoter
Model: BT16063
SAFETY
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device has been tested and found to comply with the limits for a Class B digital device pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This device generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television reception, which can be
determined by turning the device off and on is encouraged to try to correct the interference by one or
more of the following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the device and receiver.
. Connect the device into an outlet on a circuit different from that to which the receiver is connected.
. Consult the dealer or an experienced radio/television technician for help.
Declaration of Conformity for EU countries
. EMC Directive 2014/30/EU (including amendments)
. Low Voltage Directive 2014/35/EU
. RED Directive 2014/53/EU (if product has RF function)
WEEE
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure
utmost protection of the global environment, please recycle it.

INTRODUCTION
IR Remote control

INTRODUCTION
BT Remote control

INTRODUCTION

Pairing your BT remote control with the projector
Press the [HOME] and [BACK] buttons simultaneously for 2 seconds. The status LED on the BT remote
control will flash, indicating the device is in pairing mode.
The pairing process will take approximately 20 seconds. If the pairing is successful, the status LED on the
BT remote control will turn solid blue. Otherwise, the status LED on the BT remote control will turn solid
red. If the BT remote control is left idle for 10 minutes, it will automatically enter Sleep mode and the
Bluetooth is disconnected.
Note:
. The actual remote control may vary depending on the region.
. Some keys may have no function for models that do not support these features.
. Before using the remote control for the first time, remove the transparent insulation tape..

SETUP AND INSTALLATION
Remote setup
Installing / replacing the battery
1. Use a coin to turn the battery cover counterclockwise until the cover opens.
2. Install new battery into the compartment.
Remove the old battery and install new one (CR2032). Ensure that the side with a “+” is facing up.
3. Put the cover back. Then use a coin to turn the battery cover clockwise to lock it in place.

CAUTION:
To ensure safe operation, please observe the following precautions:
. Use CR2032 type battery.
. Avoid contact with water or liquid.
. Do not expose the remote control to moisture or heat.
. Do not drop the remote control.
. If the battery has leaked in the remote control, carefully wipe the case clean and install new battery.
. Risk of an explosion if battery is replaced by an incorrect type.
. Dispose of used battery according to the instructions.
Effective range
Infra-Red (IR) remote control sensor is located on the rear of the projector. Ensure to hold the remote
control at an
angle within 30° (horizontally) or 20° (vertically) perpendicular to the projector’s IR remote control sensor
to function
correctly. The distance between the remote control and the sensor should not be longer than 7 meters
(~22 feet).
You can also operate the remote control by pointing it to the projected image.
Note: When pointing the remote control directly (0 degrees angle) on the IR sensor, the distance between
the remote control and the sensor should not be longer than 10 meters (~32 feet).
. Make sure that there are no obstacles between the remote control and the IR sensor on the projector
that might obstruct the infra-red beam.
. Make sure the IR transmitter of the remote control is not being shined by sunlight or fluorescent lamps
directly.
. Please keep the remote controller away from fluorescent lamps for over 2 meters or the remote
controller might become malfunction.
. If the remote control is close to Inverter-Type fluorescent lamps, it might become ineffective from time
to time.
. If the remote control and the projector are within a very short distance, the remote control might
become ineffective.
. When you aim at the screen, the effective distance is less than 7 meters from the remote control to the
screen and reflecting the IR beams back to the projector. However, the effective range might change
according to screens.

Optoma global offices
For service or support, please contact your local office.
USA
47697 Westinghouse Drive, 888-289-6786
Fremont, CA 94539, USA 510-897-8601
www.optomausa.com [e-mail]
Canada
47697 Westinghouse Drive, 888-289-6786
Fremont, CA 94539, USA 510-897-8601
www.optomausa.com [e-mail]
Latin America
47697 Westinghouse Drive, 888-289-6786
Fremont, CA 94539, USA 510-897-8601
www.optomausa.com [e-mail]
Europe
Unit 1, Network 41, Bourne End Mills,
Hemel Hempstead, Herts,
HP1 2UJ, United Kingdom [phone]
www.optoma.eu [phone]
Service Tel : [phone] [e-mail]
Benelux BV
Randstad 22-123 [phone]
1316 BW Almere [phone]

The Netherlands
www.optoma.nl
France
Batiment E [phone]
81-83 avenue Edouard Vaillant [phone]
92100 Boulogne Billancourt, France [e-mail]
Spain
C/ José Hierro,36 Of. 1C [phone]
28522 Rivas VaciaMadrid, [phone]
Spain
Deutschland
Wiesenstrasse 21 W [phone]
D40549 Düsseldorf, [phone]
Germany [e-mail]
Scandinavia
Lerpeveien 25 [phone]
3040 Drammen [phone]
Norway [e-mail]
PO.BOX 9515
3038 Drammen
Norway
Korea
WOOMI TECH.CO.,LTD. +82+2+34430004
4F, Minu Bldg.33-14, Kangnam-Ku, +82+2+34430005
Seoul,135-815, KOREA
korea.optoma.com
Japan
東京都足立区綾瀬3-25-18
株式会社オーエス[e-mail]
コンタクトセンター:0120-380-495 www.os-worldwide.com
Taiwan
12F., No.213, Sec. 3, Beixin Rd., [phone]
Xindian Dist., New Taipei City 231, [phone]
Taiwan, R.O.C. [e-mail]
www.optoma.com.tw asia.optoma.com
Hong Kong
Unit A, 27/F Dragon Centre,
79 Wing Hong Street, [phone]
Cheung Sha Wan, [phone]
Kowloon, Hong Kong www.optoma.com.hk
China
5F, No. 1205, Kaixuan Rd., [phone]
Changning District [phone]
Shanghai, 200052, China www.optoma.com.cn