oraimo OIM-812A User manual

ICE MAKER
OIM-812A
User Manual
[email protected]
us.oraimo.com
Scan to Visit Our Website

CONTENTS
1
IMPORTANT
SAFETY
INSTRUCTIONS
1-2
2
KNOWING
YOUR
ICE MAKER
3-6
3
USING
YOUR
ICE MAKER
7-9
4
CLEANING
AND
MAINTENANCE
10-12
5
TROUBLE-
SHOOTING
GUIDE
13-15
6
WARRANTY
AND
SERVICE
15
ICE MAKER

01
Ice Maker
READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFERENCE
Specications
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning the use of the appliance by person responsible for their safety.
Close supervision is necessary when any appliance is used by or near children. Children should be
supervised to ensure that they do not play with the appliance. Cleaning and user maintenance shall not
be done by children unless they are older than 8 and supervised. Keep the appliance and its cord out of
reach of children.
Use the appliance only for intended household purposes as described in this User Manual.
INTENDED USE
When using an electrical appliance, especially when children are present, basic safety
precautions should always be followed, including the following:
This appliance must be provided with correct voltage via a professionally installed power socket. Make sure
the voltage indicated on the label of the appliance is the same as your local supply.
ELECTRICITY SAFETY
DO NOT attempt to disassemble, repair, modify or replace any part of the appliance. No user serviceable
parts inside. All servicing should be performed by qualied personnel only.
Always place and use the appliance on a dry, stable and level surface with sufcient ventilation, away from
heat sources. Leave at least 6 inches of clearance on the sides and back for proper ventilation.
Always turn the appliance OFF and unplug it before cleaning, or whenever not in use.
Always turn the appliance OFF and unplug it before making any repairs or servicing to avoid electric shock
or UV radiation.
DO NOT sit on or place any object on top of the appliance.
DO NOT use with water that is micro-biologically unsafe or of unknown quality.
DO NOT use mechanical devices to defrost. Carry out self-cleaning cycle to remove any frozen parts.
If the appliance is stored in a cold environment, wait at least 3 hours for the appliance to warm to room
temperature before plugging it in.
Regarding the use of ammable blowing agent and refrigerant, dispose of the ice maker in accordance with
local regulations.
Use caution and handle with care when moving, handling and using the ice maker to avoid damaging to the
refrigerant tubing or increasing the risk of leakage.
Damaged parts (e.g., compressor, condenser, motor and copper pipe etc.,) shall be replaced with the same
one by authorized personnel to minimize the risk of possible ignition resulting from incorrect parts or
improper servicing.
This ice maker complies with the applicable terms in Code of Federal Regulations, including 21 CFR, Chapter 1.
DO NOT attempt to replace UV lamp by yourself. Have the lamp replaced by authorized personnel only.
RELATED TO USE
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
DO NOT touch or hold the mains plug with wet hands.
02
Ice Maker
Fill the water tank with fresh potable water or connect
with water ltration system to prolong the service life.
IMPORTANT SAFETY
INSTRUCTIONS
IMPORTANT SAFETY
INSTRUCTIONS
DO NOT tilt the ice maker. If tipped over, set it upright
on a at, level surface for at least 2 hours before use.
DO NOT operate the appliance with a damaged cord or plug or if the product malfunctions, is dropped or
damaged in any manner.
Always plug the appliance directly into a wall outlet / receptacle. Never use with an extension cord or
relocatable power tap (outlet / power strip).
DO NOT let cord hang over the edge of table or counter, or touch hot surfaces.
DO NOT immerse any part in water or any other liquid.
Model
Input
Rated Power
Ice Bin Capacity
Water Tank
Daily Production
Dimensions
OIM-812A
120V~ 60Hz
170W
3.3lbs./1.5kg
0.7Gal./2.6L
33lbs./15kg (at ambient temperature 70℉, water temperature 60℉)
19.0 x 9.7 x 16.7in

04
Ice Maker
FRONT
Inlet Pipe
(9.8ft. / 3m)
Ice Scoop
02
KNOWING
YOUR
ICE MAKER
This ice maker may have been tilted or placed upside down during transportation.
Please set it upright for at least 2 hours before initial use to allow the refrigerant
uid to settle.
2h
Ice Bin
Control Panel
& Display
Water Tank
MAX Fill Line
Front Door
(with Transparent Window)
Ice Full Sensor
Water Filter
Water Level
Detector
REAR
Water Inlet
(for Automatic Rell)
Power Cord
Drain Plug
Drainpipe
(for water line)
Drainpipe
(for water tank)

05
Ice Maker
Control Buttons
06
Ice Maker
LED Display
Preset/Current
Time Setting
Self-cleaningON/Standby Time Adjustment
Ice Bin Full
Indicator stays solid on
when ice bin is full.
Remove ice in time.
Add Water
Indicator stays solid on
when tank is lack of water.
Add water in time.
Defrosting
Indicator stays solid on
during auto defrosting
(30-45mins). The buttons
are not responsive during
defrosting. Once completed,
the ice making cycle
will start automatically.
Current Time
(AM 12:00~11:59/
PM 12:00~11:59)
Preset Time 1
(AM 12:00~11:59)
Preset Time 2
(PM 12:00~11:59)
• Press to start
making ice or turn the
unit off (standby
mode).
• stays solid on
during ice making
cycle.
• Preset time setting
is available under
both ice making and
standby mode. When
pressing or
under standby mode,
the display will turn
off if no other
operation is done in
1min.
Hold 3 Sec
• Hold for 3s to start or
cancel self-cleaning cycle.
• For each cleaning
cycle, the ice maker
auto cleans for the rst
3mins ( stays on).
After 3mins, will ash
quickly for 5mins to
conrm whether to
deep clean the unit. If
yes, press to
conrm. If no opera-
tions is done in 5mins,
the cleaning cycle will
stop automatically.
• Once cleaning is
done or cancelled, the
ice maker will enter
standby mode.
• After continuous
running for 100 hours,
will ash slowly for
30s to remind you to
clean the ice maker.
Hold for 3s to start
cleaning.
Hol d 3 Sec
Hol d 3 Sec
Hol d 3 Sec
• Press to enter
Current/Preset 1/
Preset 2 time setting.
With the time ash-
ing, press to
adjust the specic
time in 5s.
• The preset time is
the time that the ice
making cycle starts.
To cancel preset time
setting, hold for
3s.
• If power is
disconnected, the
current time will be
remembered for 90
days.
• After entering
preset/
current time setting,
press to adjust the
time period, hour or
minute.
• During preset time
setting, press until ----
displayed to cancel.
• If power is discon-
nected, the preset
time will always be
remembered.
Hol d 3 Sec

03
USING YOUR
ICE MAKER
08
Ice Maker
Scoop Ice Out
The ice maker will start to produce ice in 15 minutes. Scoop
the ice cubes out once made.
Put in use or store in freezer to avoid melting.
* If the ice bin is placed back in 5mins, the ice maker will continue making ice.
Start Making Ice
Plug into a properly installed grounded outlet, then press
button to start ice making cycle. It will keep making ice until
the ice bin is full.
Add Water Manually
Open the front door and pull the ice bin out. Fill the water
tank with potable water below MAX line. Place the ice bin
back and close the door.
* Recommended water type: distilled or demineralized water (hardness
< 12 grains per gallon) at 40~82°F.
Getting Started
Make sure the drain plug is rmly inserted before use.
The ice maker will stop making ice when the ice bin has been pulled out for more
than 5mins. Once pulled out, remember to place it back within 5 mins to
continue the ice making cycle.
Locate and Clean
Locate upright on a at, level surface with at least 6 inches
of clearance on the sides and back. Clean the tank, ice bin
and ice scoop, then settle for at least 2 hours before rst
use.
6 inch
6 inch

Connect with Water Supply
System
Connect the other end with water
supply system. A 1/4'' connector may
be required.
* It is recommended to connect with
water ltration system to avoid blockage
by scale or mineral build-up.
Automatic Relling
To add water automatically, connect the included hose to the water supply system as
instructed. An adapter (not included) may be required as per the type of water supply
system in your home.
To avoid overow of water, do not add water manually when the ice maker is already
connected to the water supply system.
Insert the Hose
Fully insert the included hose into the
water inlet till the end is reached.
To remove, hold against the gray ring
and pull out.
1 2
Remove
1
2
Insert
1/4'' Adapter
(Not Included)
04
CLEANING AND
MAINTENANCE
09
Ice Maker
•
•

Self-Cleaning
To keep your nugget ice tasting fresh, we recommend that you carry out
self-cleaning at least once every 1 to 2 weeks.
Fill the tank with water below MAX line or
connect with water supply system.
Hold for 3s to start a self-cleaning cycle.
The ice maker auto cleans for the rst 3mins
(stays on). After 3mins, will ash
quickly for 5mins to conrm whether to
deep clean the unit. If yes, press
to conrm. If no operations is done in
5mins, the cleaning cycle will stop automatically.
Once completed, will turn off.
Unhook the drainpipe and lay down to
a sink.
* To resume ice making, press again.
3s
11
Ice Maker
12
Ice Maker
Regular Cleaning Removal of Scale
/Mineral Build-up
04
Hol d 3 Sec
Hol d 3 Sec
Ho ld 3 Sec
Hol d 3 Sec
Hol d 3 Sec
Hol d 3 Sec
To remove the fallen dirt or bers,
we recommend cleaning the ice
bin and water tank once a week.
Unplug before cleaning.
Unplug and take out the ice
bin. Remove the water lter
on the right corner of the tank.
Fill the water tank with warm
water (around 90°F) below
MAX line.
Add in distilled white vinegar
or ice maker cleaner. Set aside
for at least 18 hours.
Drain the mixture and continue
running 3 cleaning cycles with
fresh water for each rinse.
1
Rinse clean the ice bin and
water lter with diluted
detergent and warm water.
2
Clean the water tank with
diluted detergent, warm
water and a soft cloth. Add
water to rinse and drain out
the water.
3
Gently wipe the exterior with
a soft, damp cloth.
4
1
2
3
4
For scale or mineral build-up,
follow the directions to deep
clean periodically or when
needed. Do not clean with
solvents or chemicals.
When not in use for an extended period of time, drain the water tank and clean as
instructed. Cover and store in a cool, dry location away from direct sunlight.
18H
Hold for 3s to start
self-cleaning cycle. If
ashes, press to continue.
Repeat for at least 3 cleaning
cycles.
Hol d 3 Sec
Hol d 3 Sec

TROUBLESHOOTING GUIDE
The troubleshooting guide addresses the most common problems. If problems persist,
feel free to contact the Customer Support at [e-mail]
solid on
• Lack of water. Fill water up to the MAX
level and place the ice bin back within
5 mins, ice making cycle will restart
automatically.
• Disassemble the water lter. Check and
clean when necessary.
• Check if the water level detector is
blocked. Clear and restart.
• Scale blocked in internal pipes. Descale
as instructed.
PROBLEM SOLUTION
solid on
• Ice bin full. Remove ice and place the ice
bin back within 5 mins, ice making cycle
will restart automatically.
• Ice full sensor damaged. Contact
Customer Support for help.
• Dirt on ice full sensor. Wipe clean with a
soft, damp cloth.
13
Ice Maker
14
Ice Maker
The ice maker does not
work or stops making
ice suddenly
Noise during ice making
• Make sure the ice maker is placed
upright on a at, level surface with at
least 6 inches of clearance on the sides
and back.
• Check if the fan at the back is blocked
by any foreign objects.
• Carry out a self-cleaning cycle to
remove any frozen parts.
• During a freezing cycle, it is normal to hear
the ice scrapping, the fan moving air and the
water pump circulating water.
Water leaks
• Check if the hose is fully inserted into the
water inlet till the end is reached.
• Unplug the hose and check if the inserted
end is intact and at. Cut for a new at end
when necessary.
• Wrap the connection part with PTFE thread
seal tape for a tight connection.
Ice making cycle is
normal but no ice is
being formed
• Ice making capacity goes down as the
environmental temperatures go up, and will
be severely reduced at temperatures over 90°F.
• A restricted drain or standing water in the
water tank. Check the drainpipe for kinks.
• Check if lights up. stays solid on
during ice making cycle.
• Check if the tank is lack of water.
Fill with water and place the ice bin back
within 5 mins, ice making cycle will restart
automatically.
• The ice maker will stop making ice when the
ice bin has been pulled out for more than
5mins. Once pulled out, remember to place
it back within 5 mins to continue the ice
making cycle.
• Hold for 3s to carry out a
self-cleaning cycle.
• Disassemble the lter at the bottom of
tank. Check and clean when necessary.
• Suggested ambient temperature: 50~ 90°F.
Suggested water temperature: 40~ 82°F.
Ice cubes easily melted
The ice bin is not refrigerated and the ice
cubes will melt if not used. Please put the
ice cubes in use or store in freezer once
made to avoid melting.
If no ice is produced for a long time,
will light up, indicating the ice assembly is
defrosting. Wait 30 to 45 minutes for the
ice maker to defrost and return to normal
automatically.
solid on
Ho ld 3 Sec

Thanks for choosing Oraimo Ice Maker.
This product is covered with Oraimo product and labor warranty for 12 months from the date of its
original purchase.
The warranty will not apply in cases of:
- Misuse, dismantling, or repairs performed by unauthorized personnel.
- Any appliance that has been tampered with or used for commercial purpose.
- Use of force, natural hazards, damage caused by external influences.
- Damage caused by non-observance of the User Manual, e.g. connection to an unsuitable mains supply
or non-compliance with the instructions.
- Partially or completely dismantled appliances.
- Defects caused by or resulting from damages from shipping or alteration to the product or any of its parts
that have been performed by unauthorized personnel.
We can only provide after-sales service for products that are sold by Oraimo or Oraimo authorized retailers
and distributors. If you have purchased your appliance from a different place, please contact your seller for
return and warranty issues.
※Please have your order ID ready before contacting Customer Support.
WARRANTY AND SERVICE
15
Ice Maker
Warranty Certicate
[email protected]
us.oraimo.com
Scan to Visit Our Website
Made in China
This product is covered by a guarantee from the date of purchase. The warranty is valid only
when the warranty card is properly completed. Warranty is limited to the core product. Accesso-
ries included in the package are not covered. Please contact us if you have a question or experi-
ence a problem with the product, we promise we will give you a satised solution within 24 hours.
Order ID
Product Model
Problem Description
Customer's Name
Rev_1.0
Your new ice maker may make sounds
that are not familiar. Most of these sounds
are normal. Hard surfaces like the oor,
walls, and countertops can amplify these
sounds. The following describes the
sounds and the causes.
• WHIR - When the ice maker is turned on
for the rst time, you may notice the
condenser fan spinning.
• BUZZ - When the water pump turns on
for the rst time, it may be dry and
slightly noisy. Once lled with water, the
noise reduces signicantly.
• RATTLE - Rattling noises may be
produced from the ow of the
refrigerant. These noises should reduce
signicantly once the refrigerant system
has stabilized.
• GURGLE - When the refrigerant system
shuts off, there may be a brief gurgle as
the refrigerant stops owing.
• HUM - The compressor is a motor. It
produces a low toned humming sound
while it is running.
• CLICK - As nugget ice is produced, it
drops into the ice drawer. The rst
nuggets produced are the loudest, as
they impact the bottom of the ice bin.
As the bin lls, this noise reduces
signicantly.
• SQUEAK - When the ice maker is in
need of defrosting, it may start to
squeak as ice starts to build up around
the mechanisms. The defost cycle is
automatic, and may take 30-45 minutes.
During this time, the front button won't
respond. More frequent squeaking
usually requires white vinegar cleaning
to remove internal mineral scale buildup.
Normal ice making noise
Intertek
4008051
CM