Orion AVM-57188BTG User manual

DVD/VCD/CD/WMA/MP3 PLAYER WITH FM/MW RECEIVER
INSTRUCTION MANUAL
PLEASE READ THIS MANUAL BEFORE USING THE EQUIPMENT.
BUILT-IN NAVIGATION SYSTEM
PTY
REL
DN
UP
VOL
TA AF OPEN
IR
SRC
MUTE
BAND/
POWER
AV IN
MIC
DISP
NAV
AVM-57188BTG

Thank you for buying this product, please read through these operating
instructions, so you will know how to operate your model properly.
After you have finished reading the instructions, put them away in a safe
place for future reference .
CONTENTS
Note:
Due to continuous product improvement, specifications and design are
subject to change without prior notice.
PRECAUTIONS
FRONT PANEL
REMOTE CONTROL
RADIO OPERATION
DVD/VCD/CD OPERATION
SYSTEM SETUP
1
3
6
10
14
19
22
MP3 OPERATION 26
BASIC OPERATION 13
SYSTEM MENU
CABLE CONNECTION
ACCESSORIES
INSTALLATION 28
30
32
TROUBLE SHOOTING
SPECIFICATION
30
31
NAVIGATION OPERATION
27
BLUETOOTH OPERATION 16
DVB-T OPERATION 18

PRECAUTIONS
1
PRECAUTIONS
1. Be sure to connect the color coded leads according to the diagram.
Incorrect connections may cause the unit to malfunction or damage the vehicles
electrical system.
2. Be sure to connect the speaker (-) leads to the speaker (-) terminal.
Never connect the left and right channel speaker cables each other or to the vehicle body.
3.Make sure all the connections are completely correct before turning on your unit.
4. When replacing the fuse(s), the replacement must be of the same amperage as shown
on the fuse holder.
5. Do not block vents or radiator panels.
Doing so many cause heat to build up inside and may result in fire.
6 After completing the installation and beginning to play the unit
(including replacing the battery),
please press RESET button on the front panel with pointed object
(such as ballpoint pen) to set the unit to initial status.
Replaclng the Fuse
Make sure the amperage matches the specified value when replacing the fuses.
If the fuse is blown, check the power connection and replace with a new one.
If the same problem occurs, lt would be subjected to the malfunction in-house.
In such cases, please consult the nearest service dealer.
WARNING:
Never use the fuse with the rated amperage more than that supplied to your unit,
other wise lt will damage the unit.
IMPORTANT:
Please adjust screen to make the touching effect function best when you initiate
the unit for the first time.
For the details, please refer to the operation at Page 8.

This unit can play the following discs only:
Type of disc
VCD
12cm
MP3
12cm
CD 12cm
NOTE: The unit is compatible with VCD1.0/2.0/3.0 version and DVCD disc.
F
12cm
DVD
Label on the disc Recorded material Size of disc
Do not attempt to modify the
unit, modifying the unit may
cause an accident.
Stop the vehicle before carrying
out any operation that could
interfere with your driving.
Do not work in extremely high or
low temperature. Be sure the
temperature inside the vehicle
is between +60 C and -10 C
before turning on your unit .
To enjoy optimum sound and
images while playing, handle the
discs as follows:
Handle the disc by its edge to
keep the disc clean, and do not
touch the surface.
Do not use your disc with paste
residue or ink attached.
Do not use disc with labels or
stickers attached, which may leave
a sticky residue while beginning to
peel off.
(Shown as the picture)
Clean the discs with an optio-
nal cleaning cloth. Wipe each disc
from the center out.
(Shown as the picture)
Sound and moving
pictures
Sound and moving
pictures
Sound only
Sound only
2
PRECAUTIONS
PRECAUTIONS

MENU
TILT
FRONT PANEL
FRONT PANEL
3
20
23
21
24
22
25
PTY
REL
DN
UP
VOL
TA AF OPEN
IR
SRC
MUTE
BAND/
POWER
AV IN
MIC
DISP
NAV
3
6
15
16
17
14
13
12
4
5
78 9 10 11 12
1819
26

4
FRONT PANEL
1. MIC
2. TA
Press this buttonto turn on/off TA function.
3. PTY
Press this buttonto select oneof the
program type inRDS mode.
4. REL
Press this buttonto open thefront panel.
5. VOL
Adjust thevolume by turningthe knob
clockwise or counterclockwise.Press
this button brieflyto display themenu.
You can choose one of the following
settings:
L-front/R-front/L-rear/R-rearsubwoof/
Bass / Middle/ Treble/ TILT/ Volume.
Rotate the buttonto adjust tothe setting.
6/7.
In radio mode,press one ofthese buttons
to seek astation manually.
Hold down oneof the buttonsto seek
a station automatically.
In DVD/USB/CARD modepress the
buttons to selectthe previous ornext file.
Hold down thebutton for 2sto fast
forward or fastbackward.
8. BAND/ >II
In radio mode,press this buttonto select
the bands.
In play mode,press this buttonto
pause or resumeplayback.
9. SRC/NAV
Press this buttonto select oneof the
sources.
Press and holdthis button toenter
navigation mode.
10.POWER/MUTE
Press the buttonto turn onthe unit, press
and hold thebutton to turnoff the unit.
When the unitis switched on,press the
button to shutoff the sound output.
Press it againto resume thesound level.
11. AV IN
Connect theAV cable (supplied) to the
external AV device, then press the SRC
button to switchto AV1 mode.
12.SD slot
Insert an SD/MMC card, the unit will play
the files from SD/MMC card automatically.
NOTE: Once the SD/MMC card could not
eject after pressing, just pull it out manually.
13. USB port
Insert USB device, the unit will play the files
from USB automatically.
14.IR WINDOW
15.
Press the button to eject a disc when it is
loaded into the unit.
16. OPEN
Press to open or close the TFT display.
17. DISP/AF
Hold down the button to display the current
time, sources of front and rear displays and
medias (Disc, USB, SD) available.
Press this button to turn on/off TAfunction.
18. DISC Loading Slot
19. LCD display
20.Anti-theft led indicator
It will flash when the detachable control
panel is removed.
21. RESET
Using a sharp object such as a pencil to
reset the unit.
22. TFT display
23/24. TILT /
Press button to adjust the angle of
TFT display.
25. MENU
In DVD mode, press the button to display
the DVD SETUP menu. Hold down the
button to display the SYSTEM SETUP menu.
In other modes, press the button to display
the SYSTEM SETUP menu.
26. GPS SD card slot
Press and hold it to
force ejecting a disc when the system is
accidentally frozen.
/
/

5
SYSTEM MENU
The users can perform operation by touching screen directly.
1. LIGHT MODE
Touch this button to select day/night
light mode
2. Source
To display the SOURCE SETUP page
3.station preset button
to display the preset station list
(long touch to save the current
frequency into the station )
4.BAND
to switch bands.
5.LOC
to select local stations or distant station
6.EQ
to select a preset equalizer mode.
7.LOUD
to switch LOUD control function on/off
8.Page1
to enter RDS mode
9.SEEK-/SEEK+
Short press the buttons to seek a station
automatically.
Long press to seek a station manually.
10.AMS
to browse preset stations;
to search and store stations automatically
(long touch)
RADIO OPERATION RDS OPERATION
1.TA
to turn on /off TAfunction
2.AF
to turn on /off AF function
3.PTY
to switch program type
4.Page2
to switch to radio operation page.
5.SEEK-/SEEK+
to seek a station automatically.
to seek a station manually(long touch).
EON(Enhanced Other Networks)
ON:active the EON function,the unit
keep receive track of additional altern-
ate frequencies to the AF list. If the
station being received does not broad-
cast the traffic information ,the receiver
automatically tunes in the related sta-
tion that broadcasts the traffic informa-
tion when it occurs
OFF:deactive the EON function
REG(Regional)
ON:active the REG function,the unit
automatically keeps receiving the related
RDS station.
OFF:deactive the REG function
Page1
Display status of the disc
1
6
7
4
5
9
10
8
3
2
EON:OFF REG:OFF
PTY:NONE
RT:
PS:
PTY:
65.00MHz
TA AF PTY Page2
Seek- Seek+
1
2
3
4
5
1: 65.00M 2: 67.10M
4: 72.50M
3: 70.40M
6: 65.00M
5: 74.00M
65.00MHz
P1 MONO
P1 MONO

PAUSE STOP PREV NEXT SETUP
PLAY
SYSTEM MENU
6
SETUP OPERATION
TOUCH ON THE TOP LEFT POSITION
TO ENTER SOURCE INTERFACE.
The unit will return to previous mode
display screen if any operation is not
perform in 5 seconds.
1. Front
To display the front source selection screen.
Touch the item to select source displayed
on the unit screen.
2.Rear
To display the rear source selection screen.
In DVD mode, the touching screen displays
as following after touch at random position.
NOTE: Touching the left middle position
twice to display the TITLE MENU selection
screen, touching the right middle position
twice to display the ROOT MENU selection
screen, touching the right top position to
display the number keyboard.
You can select chapter(track) by pressing
the touchable screen or the RC.
4
1
2 5
3 1
2
4
5
6
3
Front Rear Audio Video SYS Exit
Front Rear Audio Video SYS Exit
12:20:25
Front:Disc
Drive:Disc
1.PLAY
To start the playback.
2.PAUSE
To pause the playback.
3.STOP
To stop playing, touch twice to stop
5.PREV/NEXT
To select previous/next chapter or tracks.
completely.
4.SETUP
To display the DVD SETUP screen.
MULTI-- PLAYER OPERATION
Front Rear Audio Video SYS Exit

Front Rear Audio Video SYS Exit
Bright
HUE
Contrast
Sharp
Bright 30
Volume
L-front
R-front
Volume:19
Front Rear Audio Video SYS Exit
7
SYSTEM MENU
3.Audio
Touch on theAUDIO button and the
screen will display as following:
In this menu, there are items of Volume,
L-front,R-fornt, L-rear, R-rear, Subwoof,
Bass, Middle and Treble can be adjusted.
Touch on the button to adjust each
item and touch on button to turn
pages and select the item listed above.
4.Video
Press on the VIDEO button and the
screen will display as following:
In this menu, there are items of Bright,
Hue, Contrast, Sharp can be adjusted.
Touch on the item that need adjusted
then touch on the button to adjust.
5.SYSTEM
To display the system setup screen.
Refer to SYSTEM SETUP OPERATION.
6.EXIT
To return to current source screen.
Key Beep
Turn on/off the sound guide function
ON: Activate the sound guide mode
OFF: Deactivate the sound guide mode.
The sound guide beep will be OFF
when any button on the unit is pressed.
Local Area
Touch the provided option to change
the radio frequency for different country.
SYSTEM SETUP OPERATION
Clock Sys
Set the time display mode(12H/24H)
Touch the provided option to adjust the
bass freq, middle freq, treble freq.
Touch the provided option to change the
subwoof freq ,the bass and middle quality
factor.
Front Rear Audio Video SYS Exit
Clock Sys
Key Beep
Local Area
Front Rear Audio Video SYS Exit
Bass freq
Middle freq
Treble freq
Front Rear Audio Video SYS Exit
Subwoof freq
BassQ factor
MidQ factor

Front Rear Audio Video SYS Exit
8
SYSTEM MENU
Night Lum (dimmer)
The function to select the backlight
brightness.(normal status's 20%,40%,
60%,80% )
Clock Adjust
adjust the time by touch
To select item your want to set
(hour, minute, second)
to change the display number
Touch Adjust
when the display position on the screen
and the touch position on the touch
panel not match, or using the product
at first time, the adjustment becomes
necessary.
Accurately touch the X mark provided
in the screen for more than 2 seconds
until the adjust succeed is displayed.
Clock Adjust
Night Lum
Touch Adjust
X < - press it
SW CONTROL
The function to select the steer wheel
control. Refer to next page.
GPS Mix SW
ON:the navigation guidance does not
interrupt the head unit
OFF: the navigation guidance interrupts
the head unit. Audio of the head unit is
muted at this time.
GPS Mix SW
SW Control
GPS Volume
GPS Volume
The function to sets the volume level
of the outputs sound through the
navigation source.
(High/Mid/Low)
Front Rear Audio Video SYS Exit

9
SYSTEM MENU
SW Control
To set 8 short-cut bottons for the
steering wheel remote control.
There are 12 buttons for selection in
each item: POWER, MODE, STOP,
PREV, NEXT, VOL+,VOL-,
Please refer to the following sequential
order to
Note:
1.The group-setting can be erased by
press
The screen will display NO KEY if there
is no set for the system.
MUTE, EJ,
PAGE UP, PAGE DOWN and MENU.
finish the setting:
1. Touch on NO KEY position on the screen;
2. Press one button on the SW control;
3. The function list jumps out on the screen;
4. Touch one of the functions as the
wanted function for the pointed button
on SW control;
ing and holding the selected group.
2. If there is already a set item, press the
corresponding button on the SW control
and the screen will display: set in X.
3. Each function can be selected into one
or more than one button of the 8 buttons
on the SW control while one button can
only be pointed as one function.
1. NO KEY
2. NO KEY
3. NO KEY
Front Rear Audio Video SYS Exit
SW CONTROL INSTALLATION
Before installing the SW control,
please make sure all the wires are
in good condition.
For installation, please refer to the
illustrations below:
Key1
Key2
GND CAR AUDIO
SWC1, orange
SWC2, brown
GND, black
SWC
SW remote control CAR AUDIO
SWC(IR), Blue/yellow
B+
GND
Key1
GND
Key2
IR
Please consult the professional
technicians for advice if the unit can
not work as expected.
in case of connecting to the SWC
(steering wheel control):
in case of connecting to the SW
remote control:
X XX
X

NAV
PTY AF TA
IR-SW
ST
REMOTE CONTROL Installing the battery
Slide the tray out on the back of the
remote control and insert the battery
with the plus (+)and minus(-)poles
pointing in the proper direction.
Use and care of the remote control
Point the remote control in the direction
of the front panel to operate to use it.
Notes:
Using batteries improperly can cause
them to explode. Take note of the follo-
wing points:
* Keep the battery out of the reach of
children. Should the battery be swallo-
wed, immediately consult a doctor.
* Use one CR2025(3V)lithium battery.
* Remove the battery if the remote con-
trol is not to be used for a month or
longer.
* Do not short-circuit, disassemble or
heat batteries.
* Do not dispose of batteries into fire or
flames.
* Dispose of spent batteries properly.
* Do not let the remote control fall onto
the floor, where it may become jam-
med under the brake or accelerator
pedals.
1.PWR/ 2. EQ
3. ANGLE/AMS 4. SUB-T/LOC
5. PROG/A-B 6. OSD/*
7. GOTO/# 8. MENU
9.
10. RPT/NAV
11. 12. ZOOM/AF
13.
[ / ][ / ][ / / / ]/ENTER
/PTY
SRC 14. VOL-/SEL/VOL+
15. 16. LOUD
17. 0-9 Number button
18. CLEAR 19.
20. TITLE 21.
22. BAND/P/N 23. SETUP
24. AUDIO/ST 25. RDM/TA
10
REMOTE CONTROL

1. POWER/
ress to mute the device.
Press it again to resume previous sound
level.
2. EQ/
Press to select the corresponding preset
modes to adjust the sound quality.
In bluetooth mode, press this button to
dial up a call or receiving a call.
3. ANGLE/AMS
In DVD mode, press to change the
viewing angle ;
4. SUB-T/LOC
In DVD playback mode, press to change
the subtitle language; In radio mode,
press to select strong or weak station
reception.
5. PROG/A-B
In playback mode, press to set the pro-
gram order to play; In mode,
press and hold to play the section of
selected chapter/track repeatedly .
6. OSD/*
In playback mode, press to display the
playback information;
Press the button to turn on the unit;
Press and hold to turn off the unit.
In power on,p
In radio mode, press to browse each
stored station .Long press to scan and
store station automatically.
In TV mode, long press the button to
scan and store channel automatically.
In other mode, press to display the
current time, the set source output
through the front and rear display, the
current available drive.(Disc/SD/USB);
In bluetooth mode, press to function as
* button on your mobile phone functions .
playback
7. GOTO/ #
In DVD mode, press the button and the
cursor button to select TITLE, CHAPTER,
REPEAT, TIME DIS P. Then
press ENTER button to set the value.
In VCD mode, press GOTO button and
cursor button to select TRACK, DISC
TIME, TRACK TIME,REPEAT, TIME
DISP. Then press ENTER button to set.
8. MENU
9. [ / ][ / ][ / / / ]/ENTER
10. RPT/NAV
In playback mode, press to select a repeat
mode.
Press and hold this button to start the
navigation mode.
AUDIO, SUBTITLE,ANGLE ,TT TIME,
CH TIME,
In CD/MP3 mode, press GOTO button
to select "Disc Go To:_ _ _", "Track Go
To _:_ _:_ _", Select Track:_ _:xx".
Then press 0-9 number buttons to set
the track you want.
In bluetooth mode, press this button to
function as # button on your mobile
phone functions .
In radio mode ,press the button and the
number button to set the frequency.
In TV mode ,press the button and the
number button to select a channel.
In playback mode ,to perform these
function as following: play fast reverse/
fast forward, find the beginning of prev-
ious chapter or track/find the beginning
of the next chapter or track
In raido (TV)mode,to search for a station
(channel),recall a prest station(channel)
In DVD setup, use the triangle buttons
to navigate file lists and the setup menus.
In DVD mode, press to return to the root
menu.
In radio mode, press this button to switch
between RDS and radio modes.
11
REMOTE CONTROL

11. /PTY
In radio mode, press to switch the RDS
program type.
In DVD/VCD mode, press to play slowly.
12. ZOOM/AF
In radio mode, press to function AF on/off.
In DVD/VCD mode, press to increase
or decrease the picture in size.
13. SRC
P
Press and hold this button to
14. VOL-/SEL/VOL+
Press VOL-/VOL+ to adjust volume.
15.
Press to eject a disc
16. LOUD/
Press this button to activate LOUD
function.
In bluetooth mode, press to hand up
your calling.
17. (0-9)NUMBER BUTTON
In radio(TV) mode,
In DVD/VCD/CD mode,press to select
any chapter or track directly.
In bluetooth mode ,press to input the
telephone number.
ress the button repeatedly to switch
sources.
change the IR to control front or rear
source.
Then press VOL+/- to adjust each item.
press the number
button to select a corresponding preset
station(channel)
Press SEL to select one of the control
item:L-front/R-front/L-rear/R-rear/Sub-
woof/Bass/Middle/Treble/Angle/Volume.
18. CLEAR
19.
Press to pause playing and press again
to resume playing.
20. TITLE
22. BAND/P/N
In radio mode,press to select bands.
In DVD/VCD mode,press P/N button to
select PAL AUTO or NTSC.
23. SETUP
In playback mode, short press to display
DVD setting, long press in DVD mode
and press in other modes will display
system settings.
24. AUDIO/ST
In DVD mode, press to change the audio
language.
In VCD mode ,press to change the channel
mode.
In FM mode, press to select stereo or mono
reception.
25. RDM/TA
In radio mode, press to function TA o/off.
In playback mode, press to play tracks in
a random order.
Press the button to clear the erroneous
number what you import.
In DVD mode, press the button to return
the title menu.
In VCD mode, press this button to turn
on/off PBC function.
21.
Press to stop playback.
12
REMOTE CONTROL

BASIC OPERATION
13
ROCK
POP CLASSIC
EQ OFF
Volume
Subwoof
Treble
L-front R-front L-rear R-rear
Bass
Middle
TILT
1.Reset the Unit
When operating the unit for the first
time or after replacing the car battery,
you must reset the unit.
Remove the guard against theft front panel
at first, then press RESET button
with a pointed object, (such as a
ball-point pen) to set the unit to initial
status.
This function can only be operated
by the head unit.
2.Turning the Unit On/Off
Press PWR button to turn on the unit.In
unit ON,when insert a disc,the unit will
automatically start playing.
Long pressing it to turn off the unit
completely.
Pressing PWR button on the head unit
also performs the same operation.
3.Volume Control
Press VOL+ button on the remote
control to increase the sound level and
press VOL- button on the remote
control to decrease the sound level.
Rotating VOL button on the head
unit or touching the VOL-/VOL+ on the
TFT panel also performs the same
operation.
4.Setting the Sound Characteristics
Repeatedly press SEL button to select
the desired mode in the following order:
Note:
* After selecting the desired mode,
you can adjust the current level by
pressing VOL buttons on the
remote control.
,
* If you don t adjust VOL button in 3
seconds after selecting the desired
mode, the unit will automatically
return to the current mode being
displayed.
5.Turning Loudness On/Off
Short press LOUD button on the remote
control to activate loud function.
Press it again to shut down LOUD
function.
6.EQ Setting
While listening to music, you can
select the corresponding preset
(popular/classic /rock) modes, you can
adjust the sound texture more precisely
by using EQ button on the remote control.
Repeatedly pressing EQ button to
choose the following modes in turn:

Page1
1: 65.00M 2: 67.10M
4: 72.50M
3: 70.40M
6: 65.00M
5: 74.00M
65.00MHz
P1 MONO
RADIO OPERATION
14
FM2
MW2 MW1
FM3
FM1
5.DX/LOC Selector
In radio mode, press LOC button on the
remote control to select strong or weak
station reception.
5.1 LOC
When LOC:ON displays on the touch screen,
only strong signal stations will be tuned.
5.2 DX
When LOC:OFF displays on the touch screen,
both strong and weak stations can be received.
Note:
* The initial mode is DX mode.
6.MO/ST Selector
In FM of radio mode, you can press ST
button on the remote control to select
Mono mode or Stereo mode.
1.Band Select
In radio mode, repeatedly press BAND
button on the remote control to select
a band in the following order:
Select radio mode
Press SRC buttonon the remotecontrol
or on thepanel to selectRADIO mode.
NOTE: Touch on left top area of the
screen to displaythe sources screen
then RADIO modecan be selected.
Note: Press BAND on the touch screen or
on the panel also performs the same
operation.
2. Tuning
2.1 Automatic Tuning
There are three ways to tune in a station
downwards automatically as below:
press button on the remote control;
press button on the panel;
touch on SEEK- button on the touch screen.
There are three ways to tune in a station
upwards automatically as below:
press button on the remote control;
press button on the panel;
touch on SEEK+ button on the touch screen.
2.1 Manual Tuning
There are three ways to tune in a station
downwards manually as below:
press and hold button on the remote
control;
press and hold button on the panel;
touch on SEEK- button on the touch screen.
There are three ways to tune in a station
upwards automatically as below:
press and hold button on the remote
control;
press and hold button on the panel;
touch and hold on SEEK+ button on the
touch screen.
4.Store stations
4.1 Auto store
It is a function for storing up to 6 stations.
Follow the two steps:
Select the desired band;
hold down AMS button,the stations with
good reception are stored automatically.
4.2 Manual store
To turn in a station to be stored in the preset
memory, press and hold any one of the preset
buttons (1-6) to store on.
*If a new station will be stored in a preset
memory which already has a station, the
current station will be cleared and replaced
by the new station.
3.Recalling a preset station
A total of 30 preset stations (18-FM,12-MW)
are available in memory.
Press / button on the remote control
to recall a preset station.
The display shows the preset number and
frequency of the stored station, touch one
of these to select a corresponding station
for listening.
Note: Press any one of the station preset
buttons on the remote control also selects
preset station.

RADIO OPERATION
15
Receiving Traffic information
1.Press the TA button to switch on TA
mode.
2.The unit search for traffic information
station automatically. When a traffic
information station is tuned in, the TP
mark display on touchable screen. If you
do not want to listen to the traffic information
being received, press TA button to skip that
traffic information message.
The TA function will remain in the ON
position. And the unit will be back to
previous mode.
3.Press it again to switch off TAmode.
RDS (RADIO DATA SYSTEM) OPERATION
The RDS allows you to receive a
variety of information such as traffic
information,station names,and to
automatically retune to a stronger
transmitter that is broadcasting the
same programme.
Tips
The RDS digital data includes the followings:
PI Programme Identification
PS Programme Service Name
AF List of Alternative Frequencies
TP Traffic Programme
TA Traffic Announcement
PTY Programme Type
EON Enhanced Other Networks
Turn on/off the AF function
* Press AF button to switch on/off AF
function
*The tuner will search for a station with
RDS information
* The tuner will retune frequencies when
ever the reception signals getting worse.
* Traffic information is heard only when
it is being broadcast.
In other mode, Traffic announcement
can interrupt the source sound output
when broadcast. After broadcasted ,the
unit will automatically return to the original
source play before the traffic information
broadcast began.
PTY(Programme Type)Tuning
The PTY function allows you to search
for stations with a particular Program
Type. Touching Page1 button on the radio
display screen to switch to the RDS screen.
-
1.Press PTY button on touchable screen
or on the remote control to select a prog
ramme type. After selecting the progra-
mme type for 3 seconds, the unit will
search for a station in the selected pro-
gramme type.
*If the PTY station is found,the tuner
will be stop searching.
*If the PTY station is not found, No Pty
will be display on the screen.
All types for your selection are listed in
table as below:
NEWS
CURRENT AFFAIR
INFORMATION
SPORTS
EDUCATION
DRAMA
CULTURE
SCIENCE
VARIED
ROCK MUSIC
M.O.R. MUSIC
LIGHT CLASSIC
SERIOUS CLASSIC
OTHER MUSIC
WEATHER
FINANCE
CHILDREN
SOCIAL AFFAIR
PHONE IN
TRAVEL
LEISURE
JAZZ MUSIC
COUNTRY
NATIONAL
OLDIES
FOLK
POP MUSIC RELIGION
DOCUMENTARY
TEST ALARM
An emergency broadcasting(ALARM)
will broadcast automatically and pro-
duce the beep sound when it is rec-
eived.the sound output through other
source will be muted.
EON:OFF REG:OFF
PTY:NONE
RT:
PS:
PTY:
65.00MHz
TA AF PTY Page2
Seek- Seek+
P1 MONO

BLUETOOTH OPERATION
16
Selecting BT mode
Selecting bluetooth device
by using mobile phone.
Input a pass code:1234.
The connection is done.
The screen display Connect.
CONNECTING
The unit is compatible with Bluetooth
international standard wireless
cummunication technology.
You can place a hands-free call by a
Bluetooth compatible with the mobile phone.
*When you place a call, speak loudly
and clearly.
*Shut the windows before calling.
*It is normal that some unnatural
voice may be heard during your calling
which may be caused by the conditions
of the signals or the one who use the
mobile phone.
*Due to some special mobile phone,
you may not be able to use a hands-free
phone.
HANDS-FREE PHONE
Press PAIR button on touchable
screen to turn on the pair function.
Searching for device by using
mobile phone.
*The Bluetooth setting is required for a
,
mobile phone. Read the Owner s Manual
of the mobile phone.
*After paired ,the unit can connect with
the mobile phone automatically. in valid
range
* If the mobile phone or the device is
disconnected with the unit accidentally,
the screen will display Disconnect, just
press LINK button on the screen to re-
connect(refer to Bluethooth setup ).
Hanging up a Call
Press button on the screen to fini-
shes the call.
2.Placing a call by history:
Press button to switch to PHONE
BOOK screen.you can place a call by
selecting a person from a list of received
calls, dialed calls or missed calls.
A maximum of 16 numbers can be sto-
red in each call history. A maximum of 4
numbers be display in each page, and
touching button to turn to next page.
Dialling a call
1.
screen
Input the number required by pressing
number button on the remote control or
on the screen then press button on
the screen to dial up.
The telephone number you dialed is
appeared on the

BLUETOOTH OPERATION
17
Receiving a Call
When a call is received, a received call
sound rings ,and the calling is announced
in the display. Press button on
the screen to starts the call.
*Press / button on the remote
control also perform dial(receiving)
a call or hang up a call function
*The incoming call will interrupt the
sound output through other source,
and switch to the hands-free phone
screen automatically when it is received.
After the call is over, the unit will be
back to previous mode.
* The hands-free phone sounds output
through the built-in speakers.
When calling, press button on the
screen to switch the mode to receive
a call by using mobile phone, and
press it again to return to hands-free
mode.
BLUETOOTH AUDIO FUNCTION
Refer to CONNECT to connect
bluetooth audio devices.
Refer to bluetooth setup(PAGE 7) for
operation
*video playback is not supported.
*using remote control also perform same
operation
The key of the remote control assigned
in Bluetooth audio function
Previous/next track
Stop playback
Play/pause
Audio information of a bluetooth
compatible mobile phone,portable
player,etc.,is by wireless controll-
able/playable from the unit.

0: 44.25 1: 55.75
2: 63.75
4: 44.25
3: 77.25
5: 115.25
PAL-BG
Ant-1 CH:0
44.25Mz
CH- CH+ AMS SYSSeek- Seek+
18
TV OPERATION
TV OPERATIONS
1. Select TVmode
Press SRC buttonon the remotecontrol
or on thepanel to selecta source ofTV.
NOTE: Touch on left top area of the
screen to displaythe sources screen
then TV mode can beselected.
2. Select achannel
Toselect a desiredchannel, the usercan
choose one ofthe following ways:
2.1. By Remote control
Press or onthe remote control
to select previousor next storedchannel.
2.2. By
Press(1-9) number buttondirectly
on the remotecontrol to selecta preset
channel.
Toselect more than10 channel number,
firstly press GOTO button on the remote
control, then pressthe corresponding
number buttons.
2.3. By Touch screen
Touchon the neededchannel number
on the screen.
Touchon CH-/CH+ buttonon the screen
to turn pagesto select theexact channel.
Remote control
3.Selecting TV system
Touchrepeatedly SECAM-DK buttonon
the screen ORpress on BAND/P/Nbutton
on the remotecontrol to switchTV system.
Note: When the TV channel picture
is being broadcast,touch on the
random area ofthe screen toreturn to
the TV mode menu.
4. Search a channel
4.1 Automatic Searching
There are three ways to search a channel
downwards automatically as below:
press button on the remote control;
press button on the panel;
touch on SEEK- button on the touch screen.
There are three ways to search a channel
upwards automatically as below:
press button on the remote control;
press button on the panel;
touch on SEEK+ button on the touch screen.
4.1 Manual Tuning
There are three ways to search a channel
downwards manually as below:
press and hold button on the remote
control;
press and hold button on the panel;
touch on SEEK- button on the touch screen.
There are three ways to search a channel
upwards automatically as below:
press and hold button on the remote
control;
press and hold button on the panel;
touch and hold on SEEK+ button on the
touch screen.
5.Store channels
5.1 Auto store
Press and hold AMS button on the remote
control OR on the touch screen for 2 seconds.
The unit will search for channels and store
them under preset numbers in order of
signal strength.
5.2 Manual store
Follow the two steps:
Find a channel you want to store;
Press a preset number button on the touch
screen, under which you want to store
the channel.
*If a new channel will be stored in a preset
memory which already has a station, the
current channel will be cleared and replaced
by the new channel.