Orion SC122 User manual

NIGHT VISION
8 INFRA-RED
LEDS FOR NIGHT
TIME OPERATION
STYLISH
MODERN DESIGN
LOW PROFILE MONITOR
WITH ILLUMINATED
TOUCH BUTTONS
INTERCOM
FOR TWO WAY AUDIO
COMMUNICATION
18cm
COLOUR
LCD SCREEN
CLEAR COLOUR VIDEO FROM
HIGH QUALITY CAMERA
18
cm
INSTRUCTIONS FOR USE
ImpORTaNT! pLeaSe ReaD TheSe INSTRucTIONS caRefuLLy.
VIDEO DOOR PHONE
18cm LcD mONITOR Sc122
PROFESSIONAL
SURVEILLANCE SYSTEM

PROFESSIONAL
SURVEILLANCE SYSTEM
2VIDEO DOOR PHONE 18cm LcD mONITOR Sc122
MOUNTING SCREWS,
PLUGS & BRACKETS
OUTDOOR
CAMERA
18cm LCD
MONITOR
USER MANUAL
4 x DeTeRReNT
STIckeRS
CONTENTS:
1IDEntIfIcatIOn
15m
EXTENSION
CABLE
LOW VOLTAGE
POWER
SUPPLY
1 Microphone
2 18cm (7”) LCD colour display screen
3 Settings menu button
4Adjustment control buttons
5
6 Door bell chime selection button
7 Mute button
8Unlock button, to unlock door strike if
connected (door strike not included)
9Intercom/monitor button, to communicate
with the outdoor camera
10 Microphone
11 Camera with infra-red LED
12 Door bell button
13 Speaker
12 13 12 11103 4 5 6 7 8 9
Customer Service Phone: [phone] (Monday to Friday 8.30am – 5.30pm EST)
Email: [email protected]
For further information visit www.orionlive.com.au
PLEASE CONTACT IF YOU HAVE ANY
CONCERNS OR PROBLEMS WITH THIS PRODUCT
IMPORTANT BEFORE RETURNING THIS
PRODUCT TO THE RETAILER

PROFESSIONAL
SURVEILLANCE SYSTEM
3
VIDEO DOOR PHONE 18cm LcD mONITOR Sc122
2cOnnEctIOnS
3accESSOrIES
14 Connection of the video monitor
15 Power supply connection
16 Connection of the outdoor camera
17 Connection for door strike (not included)
15 metre extension cable
Protective film
Power supply Mounting screws,
plugs and brackets
14
15
16 17

PROFESSIONAL
SURVEILLANCE SYSTEM
4VIDEO DOOR PHONE 18cm LcD mONITOR Sc122
4SyStEm cOnnEctIOn
5InStaLLatIOn Of mOnItOr
Depend on
user’s height
Positioning
›BEFORE INSTALLATION CHECK THE UNIT FUNCTIONALITY
1. Select a suitable installation point
2. Install the bracket
a: Drill holes in the wall and insert plugs.
b: Tighten the screws.
3. Run the extension cable through the bracket hole and connect the
wires to video monitor according to wiring diagram.
4. Connect the power supply to the video monitor.
5. Insert the bracket to the slots on the rear panel of video monitor.
White (Audio)
Red (VDD)
Black (GND)
Yellow (Video)
1
23 4 5
1. Connect the 15 metre connection cable as
supplied, to the back of the monitor and
camera unit.
2. Connect the power supply to the back of
the monitor and plug into 240V AC 50Hz
power point.
Note: During pre-installation check feedback
interference noise that might be generated due
to the close proximity of the monitor and the
camera, this phenomenon is normal.
Yellow (Video) Black (GND) Red (VDD) White (Audio)
Cable colour wiring
diagram based on cables
supplied with this unit.
Power supply to video monitor
Video monitor to outdoor camera
3. Once you assured that the system operates
correctly, plan the monitor and camera
installation points within 15 metres.
Lay the extension cable out between the
desired locations for the outdoor camera and
video monitor. If you are not comfortable
doing this you may need the services of an
electrician or licenced cabler.

PROFESSIONAL
SURVEILLANCE SYSTEM
5
VIDEO DOOR PHONE 18cm LcD mONITOR Sc122
6InStaLLatIOn Of OUtDOOr camEra
1. Select a suitable installation point. It is
recommended to mount the outdoor camera
under eave at height of 1.5-1.7m from the
ground.
2. Install the bracket.
a. Drill holes in the wall and insert plugs.
b. Tighten the screws.
3. Run the extension cable through the bracket
hole and protective film. Connect the wires
to outdoor camera according to wiring
diagram. Attach protective film to the rear
panel to protect wiring connection.
4. Insert the bracket to the slots on the rear
panel of outdoor camera.
5. Tighten the screw at the bottom of outdoor
camera to secure it to the bracket.
* Cable colour wiring diagram based on cables
supplied with this unit.
White (Audio)
Red (VDD)
Black (GND)
Yellow (Video)
Lock
About 65cm70°
50cm
Depend on
user’s height
2
3
1
4
5
When installing the
camera, ensure that it is
located in a dry place.
It is important that the
camera or the electronics
do not get wet.

PROFESSIONAL
SURVEILLANCE SYSTEM
6VIDEO DOOR PHONE 18cm LcD mONITOR Sc122
8OpEratIOn
›LCD DISPLAY SETTING
Press Home menu/settings button to go into
LCD display setting menu, to adjust LCD display
brightness, contrast, saturation and reset. Inside
the LCD display setting menu, press Home
menu/settings button to navigate to between
Brightness, Contrast, Saturation and Reset
options, then press or button to adjust
the setting.
›Brightness adjustments
The brightness is divided into different divisions,
press or to adjust the setting.
›Contrast adjustments
The contrast is divided into different divisions,
press or to adjust the setting.
›Saturation adjustment
The saturation is divided into different divisions,
press or to adjust the setting.
›Reset
Press the to reset to factory setting.
›Exit
Press or to exit LCD display
setting menu.
›INTERCOM
When the door bell button on outdoor camera
got pressed, the video monitor bell chime will
ring, activate the video monitor LCD screen
and display images from the outdoor camera
automatically.
Press intercom button to communicate with
the outdoor camera. When you have finished,
press intercom button again, the video
monitor LCD screen will switch off automatically.
›Monitoring
Press intercom button, the video monitor
LCD screen will display images from the outdoor
camera. Press intercom button again, the
video monitor LCD screen will switch off.
›Unlock
If electric door strike is installed, press
unlock button to unlock door strike.
›Door Bell Chime Setting
Press Door bell chime selection button to
select different door bell chime. There are
24 different door bell chimes.
›Ring Volume Adjustment
Press or button to adjust door bell
chime volume.
›Mute
Press mute button to go into mute mode.
In mute mode, when the door bell button on
door camera unit got pressed, the mute indicator
LED will flashes, no bell chime and the video
monitor LCD screen will just display images from
the door camera unit.
7fOr ExtEnDED WIrInG
For extended wiring, existing wiring or CAT5E/CAT6
cable can be used. For use of CAT5E/CAT6 cable,
pairing of wires is recommended for installation.
Ensure that you match up connections at each end
by following the conductor colouring.
Note: maximum distance for extended wiring, retrofit existing
wiring or CAT5E/CAT6 cable connection is 100 metre.

PROFESSIONAL
SURVEILLANCE SYSTEM
7
VIDEO DOOR PHONE 18cm LcD mONITOR Sc122
9SpEcIfIcatIOnS
10 WarnInG
›Do not drop, puncture, or violently shake the camera or monitor.
›Do not tug the power supply cord, use the plug to remove it from the wall.
›Do not press more than one button at the same time.
›Do not mount in position directly exposed to sun or rain. Avoid mounting near radio transmitting
devices, metal object or heat sources.
›Do not use camera or monitor when there is a storm or lightning in your area.
›Do not crush or damage the power cable.
›Do not cover the vents on the unit, leave adequate space for ventilation.
›Use the cameras and monitor with care, avoid unnecessary force or impact.
VIDEO MONITOR
Display 18cm Colour TFT-LCD Screen
Resolution 480 X 3 (RGB) X 234
Buttons Intercom/Monitor, Unlock, Ringtone, Volume,
Mute, Settings Menu, Adjustment Control
Adjustment Brightness/Contrast/Saturation/Volume
Ringtone 24 Selectable Ringtones
›GENERAL
Power Supply 15V DC 1A
Power
Consumption 10W (Max) including camera
Dimensions 215(H) X 195(W) X 75(D) mm
Weight 460g
Operation
Temperature -5 to 50ºC
Operating Humidity 10% ~ 85%
OUTDOOR CAMERA
Sensor 6mm CMOS Sensor
Resolution 420TVL
Lens 6mm
Viewing Angle 70°
›NIGHT VISION NIGHT VISION
Infrared Light 8 Infra red LEDs
Range Up to 1 metre
›GENERAL
Power Supply From Video Door Phone
Dimensions 170(H) x 95(W) x 52(D) mm
Weight 400g
Operation temperature -5 to 50ºC
Operating Humidity 10% ~ 85%

PROFESSIONAL
SURVEILLANCE SYSTEM
Arlec guarantees this product in accordance with the Australian
Consumer Law.
Arlec also warrants to the original first purchaser of this product
(“you”) from a retailer that this product will be free of defects
in materials and workmanship for a period of 12 months from
the date of purchase; provided the product is not used other
than for the purpose, or in a manner not within the scope of the
recommendations and limitations, specified by Arlec, is new and
not damaged at the time of purchase, has not been subjected
to abuse, misuse, neglect or damage, has not been modified or
repaired without the approval of Arlec and has not been used for
commercial purposes (“Warranty”).
If you wish to claim on the Warranty, you must, at your own expense,
return the product, and provide proof of original purchase and your
name, address and telephone number, to Arlec at the address
below or the retailer from whom you originally purchased the
product within 12 months from the date of purchase.
Arlec will (or authorise the retailer to) assess any claim you may make
on the Warranty in the above manner and if, in Arlec’s reasonable
opinion, the Warranty applies, Arlec will at its own option and
expense (or authorise the retailer to) replace the product with the
12 Warranty
11 trOUBLESHOOtInG GUIDE
same or similar product or repair the product and return it to you
or refund the price you paid for the product. Arlec will bear its
own expenses of doing those things, and you must bear any other
expenses of claiming on the Warranty.
The Warranty is in addition to other rights and remedies you
may have under a law in relation to the product to which the
Warranty relates.
Our goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to
a major failure.
PROBLEM Possible Cause suggested Remedy
Monitor or door camera has
no power or not powering up
Power supply is loose or unplugged,
no power at socket outlet/power point
Check all cables and power supply connection.
Check power at socket outlet/power point.
No picture
Camera not connected Please check wiring connection, make sure all
wires are connected correctly.
Signal interference
Relocate camera and monitor, away from sun, rain,
radio transmitting devices, heat sources, metal objects
or major obstacles.
No power at monitor/camera or no power at
socket outlet/power point
Check all cables and power supply connection
Check power at socket outlet/power point.
Frozen white screen - Disconnect power to monitor, then reconnect.
When IR night vision is
activated, screen only
displays white
Infra-red LED light is reflected off from glass or
reflective objects that causing white light
Relocated camera away from windows, reflective and
glass objects, or remove obstacles.
When IR night vision is
activated, screen only
displays black and white
Infra-red LED light is activated This is normal, no action required.
Poor image quality
Signal interference
Relocate camera and monitor, away from sun, rain,
radio transmitting devices, heat sources, metal objects
or major obstacles.
Relocate camera and monitor to a different location.
LCD require adjustment Adjust brightness, contrast and saturation in
settings menu.
Audio interference Camera and monitor are too close
Camera has a high sensitivity microphone, keep the
door camera and monitor at least 5 metres apart, if the
camera must be within 5 metres of the monitor, reduce
the volume.
CPIN002634/2
Arlec Australia Pty. Ltd. ACN 009 322 105 (“Arlec”) gives the Warranty.
Arlec’s telephone number, address and email address are:
Customer Service: [phone]
Building 3, 31 – 41 Joseph Street, Blackburn North, Victoria, 3130
Blackburn North LPO, P.O. Box 1065, Blackburn North, 3130
Email: [email protected]
8VIDEO DOOR PHONE 18cm LcD mONITOR Sc122