Orlaco WISR User manual

WISR
Installation manual
No. IM0973670 A 02
Art. No: 0300100
02/2019
English
Art. No. 0300100

2
Supported tablet
with
PhotonView App
WISR router
Camera EMOS Ethernet
Installation manual
IM0973670 A 02
Preface
Only connect this product to a SELV (Separated or Safety
Extra-Low Voltage) or a double insulated power source.
Ensure that a fuse 2A T has been installed in the power
line of the WISR
Before you start using this equipment, please read this manual
carefully and follow all instructions. This installation manual
describes the functions of the equipment, outlines the
connection options and explains how to put the equipment into
operation. We recommend that you keep this manual in a safe
place for reference purposes.
If you have any questions or issues concerning the operation
of this equipment, consult the relevant section in the manual or
contact the Orlaco Products BV Service department.
All data subject to change without notice. All dimensions are
for commercial purpose only. The Orlaco products comply with
the latest CE, ADR, EMC and mirror-directive regulations, where
applicable. All products are manufactured in accordance with
the ISO 9001 quality management system, IATF 16949 quality
automotive, ISO 14001 environmental management systems,
where applicable.
Safety
In order to guarantee safe operation, these safety
instructions must be read before you start using this
equipment.
• Do not open the enclosure. This can cause damage, short-
circuiting or electrical shocks.
• Do not expose the equipment to extreme temperatures, this can
cause deformation of the enclosure or damage to internal
components.
• Repairs may only be undertaken by Orlaco.
• The equipment must be assembled as shown in this manual.
• If there have been alterations or changes to this equipment that
have not been specifically approved by Orlaco, use of this
equipment is not permitted.
• Warning! RF radiation. This device is using Radio Frequency
(RF) signals to established a wireless video link. Keep a
minimum separation distance of 0.2m between the WISR and
the human body to comply with the regulation regarding human
exposure to RF radiation.
WISR, Art. No. 0300100
Available documentation
https://www.orlaco.com/downloads
User manual: UM0972260 WISR
Data sheet:
DS0963570-0300100 WISR
DS0961110-0186000 Camera EMOS Ethernet
Package
- WISR router
- Power cable 2m
WISR system

3
Installation manual
IM0973670 A 02
Contents Page
1. Introduction 3
2. Configuration 5
3. Operation 5
4. Assembly/Installation 5
4.1. Options 5
4.2. Connections 5
4.3. The photonView app 5
5. Dimensions 6
6. Technical specifications 6
7. Electrical connections 7
8. Maintenance and cleaning 8
9. FCC Statement 8
10. IC Statement 8
11. Disposal 9
12. General terms and conditions 9
13. Release notes 10
1. Introduction
The WISR sytem provides a Wi-Fi®connection within a view
system. The WISR router is both a receiver and a transmitter.
This document describes WISR system installation.
List of abbreviations
IP(-address) Internet Protocol (Address). Unique address inside a network.
MAC (-address) Media Access Control Address. Worldwide unique address for Ethernet devices.
ROI Region Of Interest. Used to specify resolution or crops of the video image.
WISR Wireless Sender Reciever.
IMPORTANT
Avoid mounting the WISR with connectors faced up.
Preferably mounting the WISR with connectors facing down.

4
Installation manual
IM0973670 A 02
Application possibilities of the WISR system, figure. 1.
WISR router
Wi-Fi®
WISR router local (Truck cabin)
Wi-Fi
WISR router remote (Trailer)
Wi-Fi®
®
Camera EMOS EthernetCamera EMOS Ethernet
Power
Power
Power
Power
Power
Power
Power
Power
Power
Tablet
Tablet
Extension
cable
Extension
cable
Extension
cable
2 camera system
4 camera system

5
203,7
Units in mm
178,8
30
38
37
42,9
12
42,9
Installation manual
IM0973670 A 02
2. Conguration
To create a Wi-Fi®connection, there must always be a
WISR router in the system. In a 2 camera system, one
WISR router is connected with the tablet. For the 4 camera
system a second WISR router set communicates with the
other WISR router within a work zone. Figure 1 shows two
systems using one or two WISRs.
To connect two cameras with the WISR, an extension cable
must be used; This cable must be ordered separately, check
with Orlaco.
Cable Uni Ethernet
1m; Art. No. 0321000 9m; Art. No. 0321060
2m; Art. No. 0321010 11m; Art. No. 0321070
3m; Art. No. 0321020 16m; Art. No. 0321080
5m; Art. No. 0321030 21m; Art. No. 0321090
7,5m; Art. No. 0321040 40m; Art. No. 0321100
8m; Art. No. 0321050
Optionally, a holder for the tablet is available. See figure 2.
Tablet holder 8.5” to 11.125”. Article No. 2015880.
See Data sheet: DS0963137.
IMPORTANT:
Tablet charging adapter is not included
3. Operation
The WISR works together with the Android app ‘Photon-
View’. WISR firmware can be updated via Wi-Fi®with the
tablet (Android Photon View app) with a Wi-Fi®connection.
(Check with Orlaco to receive the software).
The Wi-Fi®antenna has an omnidirectional orientation.
Typically the system will cover 20m. The maximum range is
30m, measured under optimal conditions in the open field.
Local interference metal objects and weather conditions
can cause the maximum range to decrease.
4. Assembly / Installation
4.1 Options
The WISR system can be mounted in various ways.
Depending on the use, there are various mounting options
for the WISR system.
IMPORTANT
Avoid mounting the WISR with connectors
faced up. Preferably mounting the WISR
with connectors facing down.
Figure 2
IMPORTANT
The best reception of the
signal on the tablet can
be obtained by placing the tablet
and the WISR so that there is as
little as possible metal between
them.

6
Installation manual
IM0973670 A 02
4.2 Connections
Connecting the WISR system is easy. Connect the tablet to
the WISR router and the Cameras using the PhotonView
app. The detailed user instructions are listed in the User
Manual UM0972260.
Connect the camera video cables to the 4p connections on
the WISR router and the power cable with the 8p connector
on the WISR router for the supply voltage.
4.3 The photonView app
The detailed user instructions are listed in the User Manual
UM0972260.
5. Dimensions
See figure 3.
6. Technical specications
General
Description: Wireless Send Receive (WISR).
Software: The WISR works together with the Android app
‘PhotonView’.
Weight: 0,30kg.
Video encoding system: RTP/AVB, MJPEG, H.264.
Operating temperature: -40ºC to +85ºC.
Radio
Firmware: The WISR firmware can be updated via Wi-Fi®
with the tablet (Android Photon View app).
Antenna type: Internal antenna with MIMO technics.
Antenna orientation: Omnidirectional.
Frequency range: Ch. 36 ~ 48 (5170-5250 MHz) and
Ch. 149 ~ 165 (5735-5835 MHz). Depending on national
requirements.
Max. Transmitting power: 1-30 dBm E.I.R.P. Depending on
national requirements.
Maximum range: 30m open field. Local interference, metal
object and weather conditions will shorten the maximum
distance.
Electrical
Rated voltage range: 9-32V/DC.
Rated power: 5W max.
Switch Inputs: 4 Camera selection inputs plus Handbrake
and Tacho inputs 0-30V, 0-8V (low) / 8-30V (high).
Power cable: 2m m8F M12 (Art. No. 1001878).
Figure 3
Units in mm
Power
Connector
8p male Video 1, 2
Connector 4p female
Power cable 2m m8F M12
Art. no. 1001878
130,3
Power Video 1 Video 2
139
101,6
Power Video 1 Video 2
76,3
∅7,4 2x
Protection cap
Article no: XXXXXXX
Serial no. XXXXXXX
RATED VOLTAGE
9 - 32 Vdc
FCC ID: XXX-XXX
IC ID: XXXXXA-XXX
Made in the Netherlands
RATED POWER
MAX 5W
IP69K
10RXX/XX*XXXX
TDK: PR1A91DA1
42,4
139
42,4
Power Video 1 Video 2
Article no: XXXXXXX
Serial no. XXXXXXX
RATED VOLTAGE
12/24 Vdc
FCC ID: XXX-XXX
IC ID: XXXXXA-XXX
Made in the Netherlands
RATED POWER
MAX 5W
IP69K
10RXX/XX*XXXX
TDK: PR1U91DA1

7
Installation manual
IM0973670 A 02
Mechanical
Housing: Automotive thermoplastic polymer (33% glass
filled).
Ingress protection: IP67 according to IEC 60529, IP69K
according to DIN 40050-9.
Certication
Quality & environment: Unit manufactured by Orlaco in the
Netherlands; ISO 9001, ISO14001, IATF 16949.
Approvals: CE, FCC. UN Regulation No. 10.
7. Electrical connections
See figure 4.
130,3 139
42,4
Power Video 1 Video 2
139
Units in mm
101,6
Power Video 1 Video 2
Power Video 1 Video 2
Electrical connections WISR
Power socket
Pin Cable wire color Function
1 = Red = Power
2 = White = 0V
3 = Blue = CAM 1
4 = Brown = CAM 2
5 = White/Yellow = CAM 3
6 = Green = CAM 4
7 = Grey = Aux 1
8 = Yellow = Aux 2
Video 1, 2 sockets
Pin Function
1 = Tx Data +
3 = Tx Data -
2 = Recv Data +
4 = Recv Data -
5
6
7
1
4
3
2
8
Power
Connector 8p male
Video 1, 2
Connector 4p female
Power Video 1 Video 2
Power cable 2m m8F M12
Art. no. 1001878
76,3
∅7,4 2x
1
43
2
Front side Female
M12 Connector D-Coded
Front side
Male Connector
Protection cap
Article no: XXXXXXX
Serial no. XXXXXXX
RATED VOLTAGE
9 - 32 Vdc
FCC ID: XXX-XXX
IC ID: XXXXXA-XXX
Made in the Netherlands
RATED POWER
MAX 5W
IP69K
10RXX/XX*XXXX
TDK: PR1U91DA1
Article no: XXXXXXX
Serial no. XXXXXXX
RATED VOLTAGE
12/24 Vdc
FCC ID: XXX-XXX
IC ID: XXXXXA-XXX
Made in the Netherlands
RATED POWER
MAX 5W
IP69K
10RXX/XX*XXXX
TDK: PR1U91DA1
1
43
2
Figure 4
Units in mm
Power
Connector
8p male Video 1, 2
Connector 4p female
Power cable 2m m8F M12
Art. no. 1001878
130,3
Power Video 1 Video 2
139
101,6
Power Video 1 Video 2
76,3
∅7,4 2x
Protection cap
Article no: XXXXXXX
Serial no. XXXXXXX
RATED VOLTAGE
9 - 32 Vdc
FCC ID: XXX-XXX
IC ID: XXXXXA-XXX
Made in the Netherlands
RATED POWER
MAX 5W
IP69K
10RXX/XX*XXXX
TDK: PR1A91DA1
42,4
139
42,4
Power Video 1 Video 2
Article no: XXXXXXX
Serial no. XXXXXXX
RATED VOLTAGE
12/24 Vdc
FCC ID: XXX-XXX
IC ID: XXXXXA-XXX
Made in the Netherlands
RATED POWER
MAX 5W
IP69K
10RXX/XX*XXXX
TDK: PR1U91DA1
Units in mm
Power
Connector
8p male Video 1, 2
Connector 4p female
Power cable 2m m8F M12
Art. no. 1001878
130,3
Power Video 1 Video 2
139
101,6
Power Video 1 Video 2
76,3
∅7,4 2x
Protection cap
Article no: XXXXXXX
Serial no. XXXXXXX
RATED VOLTAGE
9 - 32 Vdc
FCC ID: XXX-XXX
IC ID: XXXXXA-XXX
Made in the Netherlands
RATED POWER
MAX 5W
IP69K
10RXX/XX*XXXX
TDK: PR1A91DA1
42,4
139
42,4
Power Video 1 Video 2
Article no: XXXXXXX
Serial no. XXXXXXX
RATED VOLTAGE
12/24 Vdc
FCC ID: XXX-XXX
IC ID: XXXXXA-XXX
Made in the Netherlands
RATED POWER
MAX 5W
IP69K
10RXX/XX*XXXX
TDK: PR1U91DA1

8
Installation manual
IM0973670 A 02
8. Maintenance and cleaning
Clean this product with a damp cloth. Do not use aggressive chemicals or abrasive cleaning agents.
9. FCC Statement
§15.21
Any changes or modifications not expressly approved by the party responsible for compliance could void
the users authority to operate this equipment.
Either (§15.105) class B device
The equipment has been tested and found comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause inter-
ference harmful to radio communications.
There is no guarantee, however, that interference will not occure in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can be determined by tuning
the equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
> Reorient or relocate the receiving antenna.
> Increase the separation between the equipment and receiver.
> Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
> consult the dealer or an experienced radio or TV technician for help.
10. IC Statement
(English) This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired operation of
the device
(Français) Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2)l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
(English) Caution: Exposure to Radio Frequency Radiation.
To comply with RSS 102 RF exposure compliance requirements, for mobile configurations, a separation
distance of at least 20 cm must be maintained between the antenna of this device and all persons. This
device must not be co-located or operating in conjunction with any other antenna or transmitter.

9
Installation manual
IM0973670 A 02
(Français) Pour se conformer aux exigences de conformité CNR 102 RF exposition, pour des configura-
tions mobiles, une distance de séparation d’au moins 20 cm doit être maintenue entre l’antenne de cet
appareil et toutes les personnes. Cet appareil ne doit pas être colocalisés ou fonctionnant en conjonction
avec une autre antenne ou transmetteur.
11. Disposal
Disassembly, removal and disposal. Local regulations for dealing with waste must be followed when
disposing of disassembled components or entire units.
12. General terms and conditions
Orlaco Products BV is not liable for damage resulting from inadequate servicing, incorrect usage or altera-
tions made to the equipment without informing the manufacturer in writing.
This installation manual has been made available by Orlaco Products BV. All rights reserved. No part of
this manual may be reproduced and/or made public in printed form, in photocopy form or on microfilm,
or in any other way, without the prior written permission of Orlaco. This also applies to the associated
drawings and figures.
Orlaco reserves the right to make changes to components at any time without informing customers
beforehand or directly. All dimensions given are for commercial purposes.
For information regarding repairs that is not covered in this manual, please contact the Orlaco Products
BV service department.
This manual has been prepared with all due care and attention. However, Orlaco Products BV cannot be
held responsible for any errors in this manual or any consequences thereof.
For additional technical information please contact the Orlaco Products BV Service department.
13. Release notes
Version A 01 First issue February 2019.
Version A 02 FCC statement changed, September 2019.

www.orlaco.com
ORLACO
Orlaco is a Manufacturing company that specializes in making cameras and
monitor systems for commercial vehicles, fork-lift trucks, cranes, off shore
and maritime.
Our objective is to design and produce camera systems for the professional
market that improve the drivers’ view and increase operating efficiency.
At our facility in Barneveld we locate our design, manufacturing, ware-
housing and service department.
Vision is our mission®. Orlaco therefore deploys the development, manu-
facture, supply and service of camera and display systems that will improve
safety and efficiency of all vehicles, machinery and vessels.
Our systems give the end user a view on each blind spot and will create
comfort and improved working conditions. Our active approach will support
market demands and innovations and will lead to enthusiastic ambassadors
in the market; our customers.
For more information: www.orlaco.com