Orro Simple Multiway User manual

Standard Switch Orro Switch
This installation guide is to be used only if
you are installing 1 Orro Switch where the
light(s) is controlled by 2 switches.
Simple Multiway Installation Guide

2
Need Help?
We're ready to assist you.
Installation FAQ:
General support:
Urgent issues:
Support hours:
getorro.com/setupfaq
[email protected]
[phone]
Weekdays 7am-7pm (PST)
Weekends 10am-6pm (PST)

1
Before We Start
3
Check Compatibility
7
Prepare for Install
11
Identify Wires
16
Install Orro
23
Set Up Orro
Troubleshooting
33
41

2
Before We Start

3
Installing Orro is a straightforward process but requires
handling high voltage wiring. Please be careful.
Hire a professional if you are not comfortable with the
installation or if you do not have the proper tools available.
Start the install during daylight or have a flashlight ready.
Switch installation requires your lights to be o.
Your rst time installing Orro may take up to 45 min.
You’ll get faster after each installation.
Be Safe
45
min

4
What’s in the Box
4x Wire Connectors 2x Mounting Screws
2x Plate Screws
6x Wire Labels
1x Orro Switch1x Faceplate & Mount 4x Extension Wires

5
Tools Needed
Power tools are not recommended.
Phillips
Screwdriver
Flathead
Screwdriver
Pliers
(recommended)

6
Check Compatibility

7
Maximum Load
Calculate the Total Load of your current light setup:
Identify your bulb type:
LED CFL Incandescent Halogen
Number of bulbs
controlled by switch
Wattage of
single bulb
x
[ [] ] =Total Load
LED MagLowV
CFL Incandescent
*360W max load if switch
is located in a wall box
with more than one switch
(multi-gang box)
ElecLowV
Halogen Fluorescent
150WMax Load
Bulb Type
300W 500W* 5A
Total Load must be less than Max Load (based on bulb type):
Example: [ 4 LED bulbs ] x [ 10 watts ] = 40 watts total load
Common bulb types:
(often plastic)
(often glass)
1
2
3

8
120V/60 Hz power is standard in residential homes in USA and Canada.
Orro does not rely on WiFi to make lighting decisions. However, the
switch must be connected to WiFi for setup, enabling certain features,
and getting updates.
120V/60 Hz Power Required
WiFi Required for Setup

9
Orro Switch must be installed in the location where
the switch is connected to the bulb.
If you are unsure which switch is connected to the bulb, please choose
one switch to replace. If the incorrect switch is selected, you will just
need to try again and replace the other switch.
If you are unsure, hire an electrician
to complete installation.
Multiway Switch Diagram
Install Orro Switch here
TRAVELLER WIRES
BULBPOWER

10
Prepare for Install

11
Where is my circuit breaker?
Breakers may be found in a garage, hallway, or basement. If you can’t
nd the specic breaker, turn o the master breaker. If you are installing
your switch in a multi-switch gang box, turn o breakers for all switches.
Turn O Power
1
Turn o the circuit breaker for
the light switch you’re replacing.
Check the power is OFF by toggling
your light switch on and o.
Your lights should NOT turn on.

12
Remove Faceplate
2
• Unscrew or pop o the existing faceplate.
• If there is dried paint connecting the plate
to the wall, use a box cutter to remove the
faceplate cleanly.
Remove the screws from the top and bottom
of the switch.
Unscrew Switch
3

13
Pull switch out as far as possible so that you can clearly
see all the wires in the switch box
Pull Switch Out of the Wall
4
Do NOT detach any wires!
*

14
Take a photo showing the existing wire connections
from the wall to the back of your switch. This will be
useful if you ever need to re-attach your old switch.
Take a Photo
5

15
Identify Wires

16
Having trouble nding neutral wires? Call us: [phone]
Identify Neutral Wire(s)
1
Neutral wire
(white)
• A neutral wire is required for the Orro Switch to work.
• Neutral wires are often white and can be found as a
single wire or bundle of wires..
• They may or may not be connected to your switch.

17
Label Neutral Wire(s)
2
Use the included sticker to label neutral wire(s).
Label neutral wire(s) coming out of the wall.
Label the wire beyond the wire nuts

18
Label Ground Wire
3
• Ground wires are often green or bare copper and can be
found either as a single wire or bundle. Label these wires.
• This wire may or may not be connected to the switch. Label
all ground wire(s) coming out of the wall.
Note: Your switch
wire terminal
positions may
not match this
illustration exactly
(Back of switch)
GROUND