Osaki Os Pro-3D Sigma User manual

Os Pro-3D Sigma

1-2
3-4
5
7
6
Industry Canada Notice
8
9-11
12-14
15-16
17-24
25
26
27
28

Keep Dry – Do not operate in a wet or moist condition.
1

Temperatures sufficiently high to cause burns may occur regardless of the control
setting. Do not use on an infant or invalid or on a sleeping or unconscious person.
Do not use on insensitive skin or on a person with poor blood circulation. Check the
skin in contact with the heated area of the appliance frequently to reduce the risk of
blistering.
Do Not Crush – Avoid sharp folds.
Do not use massager in close proximity to loose clothing or jewelry.
Keep long hair away from massager while in use.
2

3

4
Caution

5

6
This device complies with Industry Canada licence-exempt RSS standard(s).
1. Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
2.Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Avis d’Industrie Canada
Le présent appareil est conforme avux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence.
1. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
2.Cet appareil numérique ne dépasse pas les Rèlements sur l’interférence radio
par un appareil numérique de classe B stipulées dans les Rèlements sur
l’interférence redio d’industrie Canada.
Industry Canada Notice
Industry Canada Notice

7
8
8
Waist massage section
Bluetooth Music Speaker

8
63 9

9
54.3
34.3
51.6
23.2 20.1
22.8

10
Connect the electrical connector: B1(on the legrest) and B2(on the main unit).
AA
B1
B2
A2
A1
A2B1 B2 A1
Step 2: Install
on the legrest on the main unit

11
C
C
C C
on the legrest on the main unit

12
If an object is detected around the footrest, there will be the following caution!

13

14

1.When you encounter any problems and need to stop the massage immediately,
please press this button, and the massage chair will stop all actions.
2.User can adjust backrest recline by touching the icon.
3.User can adjust backrest incline by touching the icon.
4.User can adjust footrest incline by touching the icon.
5.User can adjust footrest recline by touching the icon.
6.The button for the footrest allows you to extend the length of the footrest.
7.The button for the footrest allows you to retract the length of the footrest.
15
1
4
5
2
3
7
6

AUTO
ON/OFF Button
Touch screen
(Main operation page)
Touch keys
16

Press this key to start the massage chair. Backrest and footrest of the massage
chair are automatically adjusted to the default angle. The remote control enters to
the main operation page.
Press this key again. Massage function stops. The massage mechanism, backrest
and footrest restore to its original position. The massage chair is turned off.
There are 7 massage functions available:
• Auto
• Manual
• Local
• Air Massage
• Avanced
• Settings
• Bluetooth button
Position: Press to adjust angles of the massage chair and zero gravity position.
Main operation page: Press to return to the main operation page.
Pause
Press this button to stop all the functions immediately.
Button light will be on when pause function is activated.
Please press again to cease pause function before using any other functions
AUTO: Press to start ‘Auto’
massage function (Press to start the auto massage program of Office PRO.).
3. The manual controller is described as follows
Main Operation Page
AUTO
Main operation page
Pause
AUTO
Position
17

1.Select 'Auto' function on the operation main page.
2.There are 15 massage modes to select from. After the selection, relevant massage
starts. The remote control enters to the adjustment page.
3. The adjustment page.
4.Body scanning will commence when the program is selected. ( Screen will show
scanning).
5.Please sit as far back in the seat as possible with your head on the pillow during
the scanning.
1 . 3D : Touch 3D to adjust 3D massage intensity ( 6 levels).
2 . Strength : Touch Strength to adjust Kneading strength ( 5 levels).
3 . Speed : Touch Speed to adjust Tapping speed ( 5 levels ).
4 . Intensity : Touch Intensity to adjust air massage intensity ( 5 levels ).
‘Auto’ Massage
Adjustment notes
18