OSP 74123LT User manual

74123LT / 74613LT / 7361MLT / 74603LT
ECO LEATHER MANAGER’S CHAIR
OPERATING INSTRUCTIONS
1
2
FEATURES
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift lever (1).
To lower seat height sit on chair and lift lever (1).
NOTE: It is normal for chair to slightly lower under
body weight.
• LOCKING TILT ADJUSTMENT
For individual comfort, this chair has been equipped with
an adjustment that will allow the user to change the tension
of the tilting feature. Turn knob (2) clockwise to increase
tension and counter-clockwise to decrease or ease the
tension. To lock return chair to the upright position and push
lever (1) in. To unlock pull lever (1) out.
NOTE: Be careful not to loosen the back tilt adjustment knob
completely.
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and
knobs are securely tightened.
3. Check that all bolts screws and knobs are tight every
three months or as needed.
4. Do not overturn back tilt knob when decreasing
tension.
5. Dispose of packing material properly. Do not use
plastic cover as head covering. It may cause
suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.
OSP FUrNITUrE rECEPTION SErIES LIMITED WArrANTY
OSP Furniture Reception Series are warranted* from date of purchase against failure due to material and workmanship as follows:
• 5 years on structural integrity of frame.
• 3 years on upholstery fabric against wear and deterioration (except leather).
• Leather is not warranted against routine scratching and scufng, as leather is subject to minor blemishes in use.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs. or
less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other
event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or
consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a two
year warranty on all parts applies. Fabric and foam is warranted for one year. This warranty gives you specic legal rights, and you may also have other rights
which vary from state to state.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts
are damaged or missing. Our Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail
parts@officestar.net, by Fax [phone], or toll free parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00
p.m. Pacific Time.

74123LT / 74613LT / 7361MLT / 74603LT
ECO LEATHER MANAGER’S CHAIR
ASSEMBLY INSTrUCTIONS
© Ofce Star Products January 2012
1
2
3
4
5
8
10
6L
6R
Remove all parts from carton, separate by part numbers indicated on parts list, and verify part quantities.
STEP 1 Insert ve Casters (2) into Base (1), push hard until you feel or hear the Caster (2) snap into place. Insert Pneumatic
Cylinder (3) into Base (1).
STEP 3 Attach Seat Plate (4) to Chair Body (5) with the arrow towards the front of the chair, using two Flat Washers (7) and two Long Screws (9) for front
holes and two Flat Washers (8) and two Short Screws (8) for rear holes. FULLY TIGHTEN ALL SCREWS USING ALLEN WRENCH (11).
STEP 2 Attach Arms (6L & 6R) to Chair Body (5) using two Arm Screws (10) for each Arm (6). FULLY TIGHTEN ALL SCREWS USING
ALLEN WRENCH (11).
STEP 4 Place the assembled seat on top of Pneumatic Cylinder (3) and apply downward pressure.
ATTENTION: MAKE SUrE ALL SCrEWS ArE FULLY TIGHTENED BEFOrE USING CHAIr.
PA R T QTY
1. Base .......................1
2. Casters .....................5
3. Pneumatic Cylinder ............1
4. Seat Plate ...................1
5. Chair Body ...................1
6. Arms (6R & 6L) ...............2
7. Flat Washers .................2
8. Short Screws .................2
9. Long Screws .................2
10. Arm Screws .................4
11. Allen Wrench (not shown) ......2
7
9