Osram DALI EASY RMC User manual

OSRAM GmbH
Kunden Service Center
Customer-Service-Center (CSC)
Steinerne Furt 62
86167 Augsburg
Germany
Tel : [phone] - 200
(kostenpichtig / charges apply)
Fax.: [phone] - 202
www.osram.com
www.osram.de
40083210531524
4008321053152 Page 1 of 2
Remote control
Operating instructions
III 2009
DALI_EASY_RMC_ba0903en_we1.01.indd
DALI EASY RMC
ON
1 2 3 4
DIP
B
D
F
CA
E
F
Ch 1
Ch 2
Ch 4
Start
Time +
Stop Time -
Ch 3
Scene 2
Scene 1
Scene 3
On/Off
Dimming
Scene 4
Description Function and application
The DALI EASY RMC remote control in conjunction with an inf-
rared receiver is used for the adjustment and functional control
of the DALI EASY III and OT EASY 60 II control units.
Function
The remote control sends digital coded infrared signals to the
DALI EASY IR infrared receiver. The receiver converts the
digital coded infrared signals into the corresponding telegrams
and transmits them to the connected control units.
Design
The DALI EASY RMC remote control is made up of the follow-
ing components:
• Infrared transmitter (A)
• Display (B)
• Function buttons (C)
• Battery compartment (D)
• DIP switch (E)
• Housing (F)
Button functions
Button Function
CH 1...
CH 4 The luminaires of a group (channels 1...4) are switched on and off (short press) and their bright-
ness is changed (long press).
Start/
time + The sequence is started (short press) or the fade time is extended (long press).
Stop/time - The current sequence is stopped (short press) or
the fade time is shortened (long press).
Scene 1 to
Scene 4 The corresponding scene is called up (short press) or stored (long press).
On/Off
Dimming All luminaires are switched on and off (short press) and their brightness is changed (long press).
Displays
Display Meaning Description
Sequence The sequence mode was
started.
Hold The sequence mode or
daylight simulation was
stopped.
Scene 1…4 The scene was called up.
Daylight scene
1...4 The daylight simulation scene was called up.
Daylight
sequence
Daylight simulation was
started.
Learn
IR sequence
IR coding is transmitted.
Command is transmitted.
Function is disabled or not
available in the activated
operating mode.

Page 2 of 2
Operation Note
For the function of the DALI EASY III and OT EASY 60 II control
units, see the separate instructions.
DIP switch positions
The following settings can be made using the DIP switches (E):
DIP switch Function
1OFF IR coding 1 is active
1ON IR coding 2 is active
2OFF Scene storage is disabled
2ON Scene storage is enabled
3OFF Sequence mode is disabled
3ON Sequence mode is enabled
4OFF Daylight simulation is disabled
4ON Daylight simulation is enabled
3/4 ON/ON Learn mode for transmitting the
IR coding and resetting the con-
trol units to the factory settings
(RESET)
Setting the infrared coding / RESET
The two infrared codings make it possible to operate two
separate lighting control units in one room using a single remote
control without mutual interference. The control unit is returned
to the factory setting by means of a RESET or by changing the
infrared coding.
Disconnect control units whose infrared coding should not
be reset or adjusted from the mains supply or interrupt the
connection to the IR receiver.
Set the desired infrared coding via the DIP switch of the
remote control:
– DIP switch 1 = OFF:
infrared coding 1 is active
– DIP switch 1 = ON:
infrared coding 2 is active
Note the positions of DIP switches 3 and 4.
Set DIP switches 3 and 4 to ON.
Point the remote control to the infrared receiver and press
any button.
Conrmation:
„LS“ appears in the display and the luminaires ash.
– 1x for infrared coding 1
– 2x for infrared coding 2
 Set DIP switches 3 and 4 to the original positions, reconnect
all control units to the mains supply and reconnect the IR
receiver.
Appendix Technical data
Power supply 2 Micro AAA / LR03 batteries (alkaline)
Infrared signal Interference-immune 38 kHz Rmap pro-
tocol, digital coded. 2 OSRAM-specic
codings are selectable.
Range Approx. 10 – 15 m
Operating
temperature 0 °C ... +40 °C
Protection type IP 20
Dimensions
(L x W x H) 120 x 57 x 26 mm
Conformity with the relevant EU directives is
conrmed by the CE symbol.